linux-kernel - [PATCH 3/9] serial: core: add rs485-rts-delay-us devicetree property for RS485

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Message-ID: <20190220152731.4051-3-martin.kepplinger@ginzinger.com>
Date:   Wed, 20 Feb 2019 16:27:25 +0100
From:   Martin Kepplinger <martin.kepplinger@...zinger.com>
To:     <gregkh@...uxfoundation.org>, <robh+dt@...nel.org>,
        <mark.rutland@....com>, <jslaby@...e.com>, <corbet@....net>,
        <richard.genoud@...il.com>, <nicolas.ferre@...rochip.com>,
        <alexandre.belloni@...tlin.com>, <ludovic.desroches@...rochip.com>,
        <mcoquelin.stm32@...il.com>, <alexandre.torgue@...com>,
        <linux-serial@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-stm32@...md-mailman.stormreply.com>
CC:     <linux-kernel@...r.kernel.org>
Subject: [PATCH 3/9] serial: core: add rs485-rts-delay-us devicetree property for RS485

struct serial_rs485 now optionally holds the rts delay values in
microseconds. Users can set these delays in their devicetree descriptions,
so this adds the microseconds-option with the "rs485-rts-delay-us" boolean
property.

Signed-off-by: Martin Kepplinger <martin.kepplinger@...zinger.com>
---
 Documentation/devicetree/bindings/serial/rs485.txt |  1 +
 drivers/tty/serial/serial_core.c                   | 11 +++++++++++
 2 files changed, 12 insertions(+)

diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt
index b92592dff6dd..77396c62b383 100644
--- a/Documentation/devicetree/bindings/serial/rs485.txt
+++ b/Documentation/devicetree/bindings/serial/rs485.txt
@@ -12,6 +12,7 @@ Optional properties:
   * b is the delay between end of data sent and rts signal in milliseconds
       it corresponds to the delay after sending data and actual release of the line.
   If this property is not specified, <0 0> is assumed.
+- rs485-rts-delay-us: the same as rs485-rts-delay, but in microseconds.
 - rs485-rts-active-low: drive RTS low when sending (default is high).
 - linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485
   feature at boot time. It can be disabled later with proper ioctl.
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 556f50aa1b58..4fb265b2c0fe 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -3097,6 +3097,17 @@ void uart_get_rs485_mode(struct device *dev, struct serial_rs485 *rs485conf)
 		rs485conf->delay_rts_after_send = 0;
 	}
 
+	ret = device_property_read_u32_array(dev, "rs485-rts-delay-us",
+					     rs485_delay, 2);
+	if (!ret) {
+		rs485conf->delay_rts_before_send = rs485_delay[0];
+		rs485conf->delay_rts_after_send = rs485_delay[1];
+		rs485conf->flags |= SER_RS485_DELAY_IN_USEC;
+	} else {
+		rs485conf->delay_rts_before_send = 0;
+		rs485conf->delay_rts_after_send = 0;
+	}
+
 	/*
 	 * Clear full-duplex and enabled flags, set RTS polarity to active high
 	 * to get to a defined state with the following properties:
-- 
2.20.1


Download attachment "smime.p7s" of type "application/x-pkcs7-signature" (3616 bytes)