linux-kernel - [RFC PATCH 0/2] RFC for Zynq QSPI controller driver

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [day] [month] [year] [list]

Message-ID: <1551337347-11035-1-git-send-email-naga.sureshkumar.relli@xilinx.com>
Date:   Thu, 28 Feb 2019 12:32:27 +0530
From:   Naga Sureshkumar Relli <naga.sureshkumar.relli@...inx.com>
To:     <broonie@...nel.org>, <bbrezillon@...nel.org>
CC:     <linux-spi@...r.kernel.org>, <dwmw2@...radead.org>,
        <marek.vasut@...il.com>, <richard@....at>,
        <linux-mtd@...ts.infradead.org>, <linux-kernel@...r.kernel.org>,
        <michal.simek@...inx.com>, <nagasuresh12@...il.com>,
        Naga Sureshkumar Relli <naga.sureshkumar.relli@...inx.com>
Subject: [RFC PATCH 0/2] RFC for Zynq QSPI controller driver

Xilinx Zynq uses a QSPI controller that implements all the functionality
required to support Quad SPI NOR flash devices.
This driver along with the SPI MEM and MTD layer is used to support
flash devices.

The flash device(s) can be connected in three configurations to this
controller:
1. Single - One flash device with 1 CS, 1 Clock and 4 IO lines.
2. Dual Parallel - Two flash devices connected with common CS and
   separate IO lines (resulting in 8 IO lines).
   In this configuration, the controller
   a) Duplicates commands, address etc. sent on both sets of 4 IO lines.
   b) Stripes data both transmitted and received i.e.
      4 bits of data is sent to the first flash and the other 4 bits
      to the second flash. Similarly read data is also consolidated.
   Due to this, TX and RX data handling in the driver need special
   handling for parallel mode.
3. Dual Stacked - Two flash devices connected with separate CS and
   4 common IO lines. This is largely similar to single, except for
   the slave selection logic.
The above configuration is conveyed to the QSPI driver through a
devicetree property(currently not implemented 2 & 3 mentioned above).

As per Boris suggestion We are currently not targetting for
dual stacked/dual parallel handling. looks like there are changes
needed in the framework to handle this. so this RFC is only for the
Single mode.

This is tested with current master branch of Linux.

Naga Sureshkumar Relli (2):
  dt-bindings: spi: Add device tree binding documentation for Zynq QSPI
    controller
  spi: spi-mem: Add support for Zynq QSPI controller

 .../devicetree/bindings/spi/spi-zynq-qspi.txt      |  25 +
 drivers/spi/Kconfig                                |   8 +
 drivers/spi/Makefile                               |   1 +
 drivers/spi/spi-zynq-qspi.c                        | 780 +++++++++++++++++++++
 4 files changed, 814 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt
 create mode 100644 drivers/spi/spi-zynq-qspi.c

-- 
2.7.4