[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20190312133452.GA210027@google.com>
Date: Tue, 12 Mar 2019 08:34:52 -0500
From: Bjorn Helgaas <helgaas@...nel.org>
To: "Z.q. Hou" <zhiqiang.hou@....com>
Cc: "linux-pci@...r.kernel.org" <linux-pci@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"robh+dt@...nel.org" <robh+dt@...nel.org>,
"mark.rutland@....com" <mark.rutland@....com>,
"l.subrahmanya@...iveil.co.in" <l.subrahmanya@...iveil.co.in>,
"shawnguo@...nel.org" <shawnguo@...nel.org>,
Leo Li <leoyang.li@....com>,
"lorenzo.pieralisi@....com" <lorenzo.pieralisi@....com>,
"catalin.marinas@....com" <catalin.marinas@....com>,
"will.deacon@....com" <will.deacon@....com>,
Mingkai Hu <mingkai.hu@....com>,
"M.h. Lian" <minghuan.lian@....com>,
Xiaowei Bao <xiaowei.bao@....com>
Subject: Re: [PATCHv4 26/28] PCI: mobiveil: ls_pcie_g4: add Workaround for
A-011451
On Tue, Mar 12, 2019 at 09:34:17AM +0000, Z.q. Hou wrote:
> Hi Bjorn,
>
> Thanks a lot for your comments!
>
> > -----Original Message-----
> > From: Bjorn Helgaas [mailto:helgaas@...nel.org]
> > Sent: 2019年3月12日 1:35
> > To: Z.q. Hou <zhiqiang.hou@....com>
> > Cc: linux-pci@...r.kernel.org; linux-arm-kernel@...ts.infradead.org;
> > devicetree@...r.kernel.org; linux-kernel@...r.kernel.org;
> > robh+dt@...nel.org; mark.rutland@....com; l.subrahmanya@...iveil.co.in;
> > shawnguo@...nel.org; Leo Li <leoyang.li@....com>;
> > lorenzo.pieralisi@....com; catalin.marinas@....com;
> > will.deacon@....com; Mingkai Hu <mingkai.hu@....com>; M.h. Lian
> > <minghuan.lian@....com>; Xiaowei Bao <xiaowei.bao@....com>
> > Subject: Re: [PATCHv4 26/28] PCI: mobiveil: ls_pcie_g4: add Workaround for
> > A-011451
> >
> > On Mon, Mar 11, 2019 at 09:33:32AM +0000, Z.q. Hou wrote:
> > > From: Hou Zhiqiang <Zhiqiang.Hou@....com>
> > >
> > > When LX2 PCIe controller is sending multiple split completions and ACK
> > > latency expires indicating that ACK should be send at priority.
> > > But because of large number of split completions and FC update DLLP,
> > > the controller does not give priority to ACK transmission. This
> > > results into ACK latency timer timeout error at the link partner and
> > > the pending TLPs are replayed by the link partner again.
> > >
> > > Workaround:
> > > 1. Reduce the ACK latency timeout value to a very small value.
> > > 2. Restrict the number of completions from the LX2 PCIe controller
> > > to 1, by changing the Max Read Request Size (MRRS) of link partner
> > > to the same value as Max Packet size (MPS).
> > >
> > > This patch implemented part 1, the part 2 can be set by kernel
> > > parameter 'pci=pcie_bus_perf'
> >
> > If I understand correctly, you're saying that LX2160A Rev1.0 will only work
> > correctly if you have this patch applied AND you boot with
> > "pci=pcie_bus_perf".
>
> Your understanding is correct.
>
> > That might be OK if these rev 1.0 parts are only used in the lab and are never
> > shipped to customers. But if these parts are ever shipped to customers, I
> > don't think it's acceptable for them to have to figure out that they must boot
> > with "pci=pcie_bus_perf". Yes, you can document that in release notes, but
> > it's still a poor user experience, and users will forget, and they will see
> > mysterious hard-to-debug issues.
Since you didn't respond here, I assume these rev 1.0 parts have been
or will be shipped to end users? Please confirm.
> > Maybe there's a way for you to automatically set that pcie_bus_perf mode?
> > With a dmesg note to indicate that you're overriding any mode the user may
> > have selected?
>
> Actually we don't have a way to set the pcie_bus_perf automatically
> under Linux, we give this parameter in kernel cmdline. Do you have
> any advice about how to set this parameter automatically under
> Linux?
The beauty of Linux being open-source is that if you need something
that doesn't exist, you are empowered to create it.
We do have one place already (cns3xxx_pcie_hw_init()) that explicitly
sets pcie_bus_config. You might be able to do something similar.
> > > This ERRATA is only for LX2160A Rev1.0, and it will be fixed in
> > > Rev2.0.
> > >
> > > Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@....com>
> > > ---
> > > V4:
> > > - no change
> > >
> > > .../pci/controller/mobiveil/pci-layerscape-gen4.c | 15 +++++++++++++++
> > > drivers/pci/controller/mobiveil/pcie-mobiveil.h | 4 ++++
> > > 2 files changed, 19 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/mobiveil/pci-layerscape-gen4.c
> > > b/drivers/pci/controller/mobiveil/pci-layerscape-gen4.c
> > > index d2c5dbbd5e3c..20ce146788ca 100644
> > > --- a/drivers/pci/controller/mobiveil/pci-layerscape-gen4.c
> > > +++ b/drivers/pci/controller/mobiveil/pci-layerscape-gen4.c
> > > @@ -82,12 +82,27 @@ static bool ls_pcie_g4_is_bridge(struct ls_pcie_g4
> > *pcie)
> > > return header_type == PCI_HEADER_TYPE_BRIDGE; }
> > >
> > > +static void workaround_A011451(struct ls_pcie_g4 *pcie) {
> > > + struct mobiveil_pcie *mv_pci = pcie->pci;
> > > + u32 val;
> > > +
> > > + /* Set ACK latency timeout */
> > > + val = csr_readl(mv_pci, GPEX_ACK_REPLAY_TO);
> > > + val &= ~(ACK_LAT_TO_VAL_MASK << ACK_LAT_TO_VAL_SHIFT);
> > > + val |= (4 << ACK_LAT_TO_VAL_SHIFT);
> > > + csr_writel(mv_pci, val, GPEX_ACK_REPLAY_TO); }
> > > +
> > > static int ls_pcie_g4_host_init(struct mobiveil_pcie *pci) {
> > > struct ls_pcie_g4 *pcie = to_ls_pcie_g4(pci);
> > >
> > > pcie->rev = csr_readb(pci, PCI_REVISION_ID);
> > >
> > > + if (pcie->rev == REV_1_0)
> > > + workaround_A011451(pcie);
> > > +
> > > return 0;
> > > }
> > >
> > > diff --git a/drivers/pci/controller/mobiveil/pcie-mobiveil.h
> > > b/drivers/pci/controller/mobiveil/pcie-mobiveil.h
> > > index ab43de5e4b2b..f0e2e4ae09b5 100644
> > > --- a/drivers/pci/controller/mobiveil/pcie-mobiveil.h
> > > +++ b/drivers/pci/controller/mobiveil/pcie-mobiveil.h
> > > @@ -85,6 +85,10 @@
> > > #define PAB_AXI_AMAP_PEX_WIN_H(win) PAB_REG_ADDR(0x0bac,
> > win)
> > > #define PAB_INTP_AXI_PIO_CLASS 0x474
> > >
> > > +#define GPEX_ACK_REPLAY_TO 0x438
> > > +#define ACK_LAT_TO_VAL_MASK 0x1fff
> > > +#define ACK_LAT_TO_VAL_SHIFT 0
> > > +
> > > #define PAB_PEX_AMAP_CTRL(win) PAB_REG_ADDR(0x4ba0,
> > win)
> > > #define AMAP_CTRL_EN_SHIFT 0
> > > #define AMAP_CTRL_TYPE_SHIFT 1
> > > --
> > > 2.17.1
> > >
>
> Thanks,
> Zhiqiang
Powered by blists - more mailing lists