[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20190315170257.12847-3-dmurphy@ti.com>
Date: Fri, 15 Mar 2019 12:02:56 -0500
From: Dan Murphy <dmurphy@...com>
To: <wg@...ndegger.com>, <mkl@...gutronix.de>, <davem@...emloft.net>
CC: <linux-can@...r.kernel.org>, <netdev@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, Dan Murphy <dmurphy@...com>
Subject: [PATCH v10 3/4] dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver
DT binding documentation for TI TCAN4x5x driver.
Signed-off-by: Dan Murphy <dmurphy@...com>
---
v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/
v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/
v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/
v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/
v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/
.../devicetree/bindings/net/can/tcan4x5x.txt | 37 +++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt
diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
new file mode 100644
index 000000000000..c388f7d9feb1
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
@@ -0,0 +1,37 @@
+Texas Instruments TCAN4x5x CAN Controller
+================================================
+
+This file provides device node information for the TCAN4x5x interface contains.
+
+Required properties:
+ - compatible: "ti,tcan4x5x"
+ - reg: 0
+ - #address-cells: 1
+ - #size-cells: 0
+ - spi-max-frequency: Maximum frequency of the SPI bus the chip can
+ operate at should be less than or equal to 18 MHz.
+ - data-ready-gpios: Interrupt GPIO for data and error reporting.
+ - device-wake-gpios: Wake up GPIO to wake up the TCAN device.
+
+See Documentation/devicetree/bindings/net/can/m_can.txt for additional
+required property details.
+
+Optional properties:
+ - reset-gpios: Hardwired output GPIO. If not defined then software
+ reset.
+ - device-state-gpios: Input GPIO that indicates if the device is in
+ a sleep state or if the device is active.
+
+Example:
+tcan4x5x: tcan4x5x@0 {
+ compatible = "ti,tcan4x5x";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <10000000>;
+ bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>;
+ data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+};
--
2.20.1.390.gb5101f9297
Powered by blists - more mailing lists