| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <703e82ad-5e1e-a03d-796c-dc1ddde7d2dc@baylibre.com>
Date: Tue, 19 Mar 2019 09:15:27 +0100
From: Neil Armstrong <narmstrong@...libre.com>
To: Chunfeng Yun <chunfeng.yun@...iatek.com>
Cc: gregkh@...uxfoundation.org, hminas@...opsys.com, balbi@...nel.org,
kishon@...com, linux-amlogic@...ts.infradead.org,
linux-usb@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue
Hi,
On 19/03/2019 02:57, Chunfeng Yun wrote:
> Hi Neil,
> On Mon, 2019-03-18 at 11:11 +0100, Neil Armstrong wrote:
>> Adds support for Amlogic G12A USB Control Glue HW.
>>
>> The Amlogic G12A SoC Family embeds 2 USB Controllers :
>> - a DWC3 IP configured as Host for USB2 and USB3
>> - a DWC2 IP configured as Peripheral USB2 Only
>>
>> A glue connects these both controllers to 2 USB2 PHYs, and optionnally
>> to an USB3+PCIE Combo PHY shared with the PCIE controller.
>>
>> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
>> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
>> setups the on-chip OTG mode selection for this PHY.
>>
>> This drivers supports the on-probe setup of the OTG mode, and manually
>> via a debugfs interface. The IRQ mode change detect is yet to be added
>> in a future patchset, mainly due to lack of hardware to validate on.
>>
>> Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
>> ---
>> drivers/usb/dwc3/Kconfig | 10 +
>> drivers/usb/dwc3/Makefile | 1 +
>> drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
>> 3 files changed, 613 insertions(+)
>> create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
>>
>> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
>> index 2b1494460d0c..d2ea9670563c 100644
>> --- a/drivers/usb/dwc3/Kconfig
>> +++ b/drivers/usb/dwc3/Kconfig
>> @@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
>> Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
>> Say 'Y' or 'M' here if you have one such device
>>
>> +config USB_DWC3_MESON_G12A
>> + tristate "Amlogic Meson G12A Platforms"
>> + depends on OF && COMMON_CLK
>> + depends on ARCH_MESON || COMPILE_TEST
>> + default USB_DWC3
>> + select USB_ROLE_SWITCH
>> + help
>> + Support USB2/3 functionality in Amlogic G12A platforms.
>> + Say 'Y' or 'M' if you have one such device.
>> +
>> config USB_DWC3_OF_SIMPLE
>> tristate "Generic OF Simple Glue Layer"
>> depends on OF && COMMON_CLK
>> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
>> index 6e3ef6144e5d..ae86da0dc5bd 100644
>> --- a/drivers/usb/dwc3/Makefile
>> +++ b/drivers/usb/dwc3/Makefile
>> @@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
>> obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
>> obj-$(CONFIG_USB_DWC3_HAPS) += dwc3-haps.o
>> obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
>> +obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
>> obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
>> obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
>> obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
>> diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
>> new file mode 100644
>> index 000000000000..9f4554e8e6e7
>> --- /dev/null
>> +++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
>> @@ -0,0 +1,602 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * USB Glue for Amlogic G12A SoCs
>> + *
>> + * Copyright (c) 2019 BayLibre, SAS
>> + * Author: Neil Armstrong <narmstrong@...libre.com>
>> + */
>> +
>> +/*
>> + * The USB is organized with a glue around the DWC3 Controller IP as :
>> + * - Control registers for each USB2 Ports
>> + * - Control registers for the USB PHY layer
>> + * - SuperSpeed PHY can be enabled only if port is used
>> + *
>> + * TOFIX:
>> + * - Add dynamic OTG switching with ID change interrupt
>> + */
>> +
[..]
>> +
>> + ret = of_platform_populate(np, NULL, NULL, dev);
>> + if (ret) {
>> + clk_disable_unprepare(priv->clk);
>> + clk_put(priv->clk);
> No need clk_put()
Exact
>> +
>> + goto err_phys_exit;
>> + }
>> +
>> + /* Setup OTG mode corresponding to the ID pin */
>> + if (priv->otg_mode == USB_DR_MODE_OTG) {
>> + /* TOFIX Handle ID mode toggling via IRQ */
>> + otg_id = dwc3_meson_g12a_get_id(priv);
>> + if (otg_id != priv->otg_phy_mode) {
>> + if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
>> + dev_warn(dev, "Failed to switch OTG mode\n");
>> + }
>> + }
>> +
>> + /* Setup role switcher */
>> + priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
>> + "snps,dwc3");
>> + priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
>> + priv->switch_desc.allow_userspace_control = true;
>> + priv->switch_desc.set = dwc3_meson_g12a_role_set;
>> + priv->switch_desc.get = dwc3_meson_g12a_role_get;
>> +
>> + priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
>> + if (IS_ERR(priv->role_switch))
>> + dev_warn(dev, "Unable to register Role Switch\n");
>> +
>> + pm_runtime_set_active(dev);
>> + pm_runtime_enable(dev);
>> + pm_runtime_get_sync(dev);
>> +
>> + return 0;
>> +
>> +err_phys_exit:
>> + for (i = 0 ; i < PHY_COUNT ; ++i)
>> + phy_exit(priv->phys[i]);
>> +
>> +err_phys_power:
>> + for (i = 0 ; i < PHY_COUNT ; ++i)
>> + phy_power_off(priv->phys[i]);
>> +
>> +err_phys_put:
>> + for (i = 0 ; i < PHY_COUNT ; ++i)
>> + phy_put(priv->phys[i]);
> you get phy by devm_phy_optional_get(), no need call phy_put(),
Indeed, also forgot these
>> +
>> + return ret;
>> +}
>> +
>> +static int dwc3_meson_g12a_remove(struct platform_device *pdev)
>> +{
>> + struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
>> + struct device *dev = &pdev->dev;
>> + int i;
>> +
>> + usb_role_switch_unregister(priv->role_switch);
>> +
>> + of_platform_depopulate(dev);
>> +
>> + for (i = 0 ; i < PHY_COUNT ; ++i) {
>> + phy_power_off(priv->phys[i]);
>> + phy_exit(priv->phys[i]);
>> + phy_put(priv->phys[i]);
> here, and remove others if have.
This is the last one I hope
>> + }
>> +
>> + pm_runtime_disable(dev);
>> + pm_runtime_put_noidle(dev);
>> + pm_runtime_set_suspended(dev);
>> +
>> + return 0;
>> +}
>> +
>> +static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
>> +{
>> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
>> +
>> + clk_disable(priv->clk);
>> +
>> + return 0;
>> +}
>> +
>> +static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
>> +{
>> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
>> +
>> + return clk_enable(priv->clk);
>> +}
>> +
>> +static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
>> +{
>> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
>> + int i;
>> +
>> + for (i = 0 ; i < PHY_COUNT ; ++i)
>> + phy_exit(priv->phys[i]);
>> +
>> + reset_control_assert(priv->reset);
>> +
>> + return 0;
>> +}
>> +
>> +static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
>> +{
>> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
>> + int i, ret;
>> +
>> + reset_control_deassert(priv->reset);
>> +
>> + dwc3_meson_g12a_usb_init(priv);
>> +
>> + /* Init PHYs */
>> + for (i = 0 ; i < PHY_COUNT ; ++i) {
>> + ret = phy_init(priv->phys[i]);
>> + if (ret)
>> + return ret;
>> + }
> Do you need power on phys?
Regulators can be tied to the PHYs, should I disable power on suspend aswell ?
>> +
>> + return 0;
>> +}
>> +
>> +static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
>> + SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
>> + SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
>> + dwc3_meson_g12a_runtime_resume, NULL)
>> +};
>> +
>> +static const struct of_device_id dwc3_meson_g12a_match[] = {
>> + { .compatible = "amlogic,meson-g12a-usb-ctrl" },
>> + { /* Sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
>> +
>> +static struct platform_driver dwc3_meson_g12a_driver = {
>> + .probe = dwc3_meson_g12a_probe,
>> + .remove = dwc3_meson_g12a_remove,
>> + .driver = {
>> + .name = "dwc3-meson-g12a",
>> + .of_match_table = dwc3_meson_g12a_match,
>> + .pm = &dwc3_meson_g12a_dev_pm_ops,
>> + },
>> +};
>> +
>> +module_platform_driver(dwc3_meson_g12a_driver);
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
>> +MODULE_AUTHOR("Neil Armstrong <narmstrong@...libre.com>");
>
>
Thanks,
Neil
Powered by blists - more mailing lists