| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <f5c82536-0f88-b8a5-cc71-d0b4f7cbaf6e@ti.com>
Date: Tue, 26 Mar 2019 13:06:27 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: Neil Armstrong <narmstrong@...libre.com>,
<gregkh@...uxfoundation.org>, <hminas@...opsys.com>,
<balbi@...nel.org>
CC: <linux-amlogic@...ts.infradead.org>, <linux-usb@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>,
Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Subject: Re: [PATCH v5 6/8] phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo
PHY Driver
On 25/03/19 3:09 PM, Neil Armstrong wrote:
> This adds support for the shared USB3 + PCIE PHY found in the
> Amlogic G12A SoC Family.
>
> It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
> the board.
>
> Selection is done by the #phy-cells, making the mode static and exclusive.
>
> Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
merged 1,2, 5 and 6 patches of this series.
Thanks
Kishon
> ---
> drivers/phy/amlogic/Kconfig | 11 +
> drivers/phy/amlogic/Makefile | 1 +
> .../phy/amlogic/phy-meson-g12a-usb3-pcie.c | 413 ++++++++++++++++++
> 3 files changed, 425 insertions(+)
> create mode 100644 drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
>
> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> index 560ff0f1ed4c..4c08c1ccdd04 100644
> --- a/drivers/phy/amlogic/Kconfig
> +++ b/drivers/phy/amlogic/Kconfig
> @@ -47,3 +47,14 @@ config PHY_MESON_G12A_USB2
> Enable this to support the Meson USB2 PHYs found in Meson
> G12A SoCs.
> If unsure, say N.
> +
> +config PHY_MESON_G12A_USB3_PCIE
> + tristate "Meson G12A USB3+PCIE Combo PHY driver"
> + default ARCH_MESON
> + depends on OF && (ARCH_MESON || COMPILE_TEST)
> + select GENERIC_PHY
> + select REGMAP_MMIO
> + help
> + Enable this to support the Meson USB3 + PCIE Combo PHY found
> + in Meson G12A SoCs.
> + If unsure, say N.
> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> index 7d4d10f5a6b3..fdd008e1b19b 100644
> --- a/drivers/phy/amlogic/Makefile
> +++ b/drivers/phy/amlogic/Makefile
> @@ -2,3 +2,4 @@ obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
> obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o
> obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o
> obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o
> diff --git a/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
> new file mode 100644
> index 000000000000..6233a7979a93
> --- /dev/null
> +++ b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c
> @@ -0,0 +1,413 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Amlogic G12A USB3 + PCIE Combo PHY driver
> + *
> + * Copyright (C) 2017 Amlogic, Inc. All rights reserved
> + * Copyright (C) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@...libre.com>
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/bitops.h>
> +#include <linux/clk.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define PHY_R0 0x00
> + #define PHY_R0_PCIE_POWER_STATE GENMASK(4, 0)
> + #define PHY_R0_PCIE_USB3_SWITCH GENMASK(6, 5)
> +
> +#define PHY_R1 0x04
> + #define PHY_R1_PHY_TX1_TERM_OFFSET GENMASK(4, 0)
> + #define PHY_R1_PHY_TX0_TERM_OFFSET GENMASK(9, 5)
> + #define PHY_R1_PHY_RX1_EQ GENMASK(12, 10)
> + #define PHY_R1_PHY_RX0_EQ GENMASK(15, 13)
> + #define PHY_R1_PHY_LOS_LEVEL GENMASK(20, 16)
> + #define PHY_R1_PHY_LOS_BIAS GENMASK(23, 21)
> + #define PHY_R1_PHY_REF_CLKDIV2 BIT(24)
> + #define PHY_R1_PHY_MPLL_MULTIPLIER GENMASK(31, 25)
> +
> +#define PHY_R2 0x08
> + #define PHY_R2_PCS_TX_DEEMPH_GEN2_6DB GENMASK(5, 0)
> + #define PHY_R2_PCS_TX_DEEMPH_GEN2_3P5DB GENMASK(11, 6)
> + #define PHY_R2_PCS_TX_DEEMPH_GEN1 GENMASK(17, 12)
> + #define PHY_R2_PHY_TX_VBOOST_LVL GENMASK(20, 18)
> +
> +#define PHY_R4 0x10
> + #define PHY_R4_PHY_CR_WRITE BIT(0)
> + #define PHY_R4_PHY_CR_READ BIT(1)
> + #define PHY_R4_PHY_CR_DATA_IN GENMASK(17, 2)
> + #define PHY_R4_PHY_CR_CAP_DATA BIT(18)
> + #define PHY_R4_PHY_CR_CAP_ADDR BIT(19)
> +
> +#define PHY_R5 0x14
> + #define PHY_R5_PHY_CR_DATA_OUT GENMASK(15, 0)
> + #define PHY_R5_PHY_CR_ACK BIT(16)
> + #define PHY_R5_PHY_BS_OUT BIT(17)
> +
> +struct phy_g12a_usb3_pcie_priv {
> + struct regmap *regmap;
> + struct regmap *regmap_cr;
> + struct clk *clk_ref;
> + struct reset_control *reset;
> + struct phy *phy;
> + unsigned int mode;
> +};
> +
> +static const struct regmap_config phy_g12a_usb3_pcie_regmap_conf = {
> + .reg_bits = 8,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .max_register = PHY_R5,
> +};
> +
> +static int phy_g12a_usb3_pcie_cr_bus_addr(struct phy_g12a_usb3_pcie_priv *priv,
> + unsigned int addr)
> +{
> + unsigned int val, reg;
> + int ret;
> +
> + reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, addr);
> +
> + regmap_write(priv->regmap, PHY_R4, reg);
> + regmap_write(priv->regmap, PHY_R4, reg);
> +
> + regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_ADDR);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + (val & PHY_R5_PHY_CR_ACK),
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + regmap_write(priv->regmap, PHY_R4, reg);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + !(val & PHY_R5_PHY_CR_ACK),
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_cr_bus_read(void *context, unsigned int addr,
> + unsigned int *data)
> +{
> + struct phy_g12a_usb3_pcie_priv *priv = context;
> + unsigned int val;
> + int ret;
> +
> + ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr);
> + if (ret)
> + return ret;
> +
> + regmap_write(priv->regmap, PHY_R4, 0);
> + regmap_write(priv->regmap, PHY_R4, PHY_R4_PHY_CR_READ);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + (val & PHY_R5_PHY_CR_ACK),
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + *data = FIELD_GET(PHY_R5_PHY_CR_DATA_OUT, val);
> +
> + regmap_write(priv->regmap, PHY_R4, 0);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + !(val & PHY_R5_PHY_CR_ACK),
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_cr_bus_write(void *context, unsigned int addr,
> + unsigned int data)
> +{
> + struct phy_g12a_usb3_pcie_priv *priv = context;
> + unsigned int val, reg;
> + int ret;
> +
> + ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr);
> + if (ret)
> + return ret;
> +
> + reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, data);
> +
> + regmap_write(priv->regmap, PHY_R4, reg);
> + regmap_write(priv->regmap, PHY_R4, reg);
> +
> + regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_DATA);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + (val & PHY_R5_PHY_CR_ACK),
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + regmap_write(priv->regmap, PHY_R4, reg);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + (val & PHY_R5_PHY_CR_ACK) == 0,
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + regmap_write(priv->regmap, PHY_R4, reg);
> +
> + regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_WRITE);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + (val & PHY_R5_PHY_CR_ACK),
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + regmap_write(priv->regmap, PHY_R4, reg);
> +
> + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val,
> + (val & PHY_R5_PHY_CR_ACK) == 0,
> + 5, 1000);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static const struct regmap_config phy_g12a_usb3_pcie_cr_regmap_conf = {
> + .reg_bits = 16,
> + .val_bits = 16,
> + .reg_read = phy_g12a_usb3_pcie_cr_bus_read,
> + .reg_write = phy_g12a_usb3_pcie_cr_bus_write,
> + .max_register = 0xffff,
> + .fast_io = true,
> +};
> +
> +static int phy_g12a_usb3_init(struct phy *phy)
> +{
> + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
> + int data, ret;
> +
> + /* Switch PHY to USB3 */
> + /* TODO figure out how to handle when PCIe was set in the bootloader */
> + regmap_update_bits(priv->regmap, PHY_R0,
> + PHY_R0_PCIE_USB3_SWITCH,
> + PHY_R0_PCIE_USB3_SWITCH);
> +
> + /*
> + * WORKAROUND: There is SSPHY suspend bug due to
> + * which USB enumerates
> + * in HS mode instead of SS mode. Workaround it by asserting
> + * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus
> + * mode
> + */
> + ret = regmap_update_bits(priv->regmap_cr, 0x102d, BIT(7), BIT(7));
> + if (ret)
> + return ret;
> +
> + ret = regmap_update_bits(priv->regmap_cr, 0x1010, 0xff0, 20);
> + if (ret)
> + return ret;
> +
> + /*
> + * Fix RX Equalization setting as follows
> + * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0
> + * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1
> + * LANE0.RX_OVRD_IN_HI.RX_EQ set to 3
> + * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1
> + */
> + ret = regmap_read(priv->regmap_cr, 0x1006, &data);
> + if (ret)
> + return ret;
> +
> + data &= ~BIT(6);
> + data |= BIT(7);
> + data &= ~(0x7 << 8);
> + data |= (0x3 << 8);
> + data |= (1 << 11);
> + ret = regmap_write(priv->regmap_cr, 0x1006, data);
> + if (ret)
> + return ret;
> +
> + /*
> + * Set EQ and TX launch amplitudes as follows
> + * LANE0.TX_OVRD_DRV_LO.PREEMPH set to 22
> + * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 127
> + * LANE0.TX_OVRD_DRV_LO.EN set to 1.
> + */
> + ret = regmap_read(priv->regmap_cr, 0x1002, &data);
> + if (ret)
> + return ret;
> +
> + data &= ~0x3f80;
> + data |= (0x16 << 7);
> + data &= ~0x7f;
> + data |= (0x7f | BIT(14));
> + ret = regmap_write(priv->regmap_cr, 0x1002, data);
> + if (ret)
> + return ret;
> +
> + /* MPLL_LOOP_CTL.PROP_CNTRL = 8 */
> + ret = regmap_update_bits(priv->regmap_cr, 0x30, 0xf << 4, 8 << 4);
> + if (ret)
> + return ret;
> +
> + regmap_update_bits(priv->regmap, PHY_R2,
> + PHY_R2_PHY_TX_VBOOST_LVL,
> + FIELD_PREP(PHY_R2_PHY_TX_VBOOST_LVL, 0x4));
> +
> + regmap_update_bits(priv->regmap, PHY_R1,
> + PHY_R1_PHY_LOS_BIAS | PHY_R1_PHY_LOS_LEVEL,
> + FIELD_PREP(PHY_R1_PHY_LOS_BIAS, 4) |
> + FIELD_PREP(PHY_R1_PHY_LOS_LEVEL, 9));
> +
> + return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_init(struct phy *phy)
> +{
> + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
> + int ret;
> +
> + ret = reset_control_reset(priv->reset);
> + if (ret)
> + return ret;
> +
> + if (priv->mode == PHY_TYPE_USB3)
> + return phy_g12a_usb3_init(phy);
> +
> + /* Power UP PCIE */
> + /* TODO figure out when the bootloader has set USB3 mode before */
> + regmap_update_bits(priv->regmap, PHY_R0,
> + PHY_R0_PCIE_POWER_STATE,
> + FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c));
> +
> + return 0;
> +}
> +
> +static int phy_g12a_usb3_pcie_exit(struct phy *phy)
> +{
> + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy);
> +
> + return reset_control_reset(priv->reset);
> +}
> +
> +static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct phy_g12a_usb3_pcie_priv *priv = dev_get_drvdata(dev);
> + unsigned int mode;
> +
> + if (args->args_count < 1) {
> + dev_err(dev, "invalid number of arguments\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + mode = args->args[0];
> +
> + if (mode != PHY_TYPE_USB3 && mode != PHY_TYPE_PCIE) {
> + dev_err(dev, "invalid phy mode select argument\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + priv->mode = mode;
> +
> + return priv->phy;
> +}
> +
> +static const struct phy_ops phy_g12a_usb3_pcie_ops = {
> + .init = phy_g12a_usb3_pcie_init,
> + .exit = phy_g12a_usb3_pcie_exit,
> + .owner = THIS_MODULE,
> +};
> +
> +static int phy_g12a_usb3_pcie_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + struct phy_g12a_usb3_pcie_priv *priv;
> + struct resource *res;
> + struct phy_provider *phy_provider;
> + void __iomem *base;
> + int ret;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + priv->regmap = devm_regmap_init_mmio(dev, base,
> + &phy_g12a_usb3_pcie_regmap_conf);
> + if (IS_ERR(priv->regmap))
> + return PTR_ERR(priv->regmap);
> +
> + priv->regmap_cr = devm_regmap_init(dev, NULL, priv,
> + &phy_g12a_usb3_pcie_cr_regmap_conf);
> + if (IS_ERR(priv->regmap_cr))
> + return PTR_ERR(priv->regmap_cr);
> +
> + priv->clk_ref = devm_clk_get(dev, "ref_clk");
> + if (IS_ERR(priv->clk_ref))
> + return PTR_ERR(priv->clk_ref);
> +
> + ret = clk_prepare_enable(priv->clk_ref);
> + if (ret)
> + goto err_disable_clk_ref;
> +
> + priv->reset = devm_reset_control_array_get(dev, false, false);
> + if (IS_ERR(priv->reset))
> + return PTR_ERR(priv->reset);
> +
> + priv->phy = devm_phy_create(dev, np, &phy_g12a_usb3_pcie_ops);
> + if (IS_ERR(priv->phy)) {
> + ret = PTR_ERR(priv->phy);
> + if (ret != -EPROBE_DEFER)
> + dev_err(dev, "failed to create PHY\n");
> +
> + return ret;
> + }
> +
> + phy_set_drvdata(priv->phy, priv);
> + dev_set_drvdata(dev, priv);
> +
> + phy_provider = devm_of_phy_provider_register(dev,
> + phy_g12a_usb3_pcie_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +
> +err_disable_clk_ref:
> + clk_disable_unprepare(priv->clk_ref);
> +
> + return ret;
> +}
> +
> +static const struct of_device_id phy_g12a_usb3_pcie_of_match[] = {
> + { .compatible = "amlogic,g12a-usb3-pcie-phy", },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, phy_g12a_usb3_pcie_of_match);
> +
> +static struct platform_driver phy_g12a_usb3_pcie_driver = {
> + .probe = phy_g12a_usb3_pcie_probe,
> + .driver = {
> + .name = "phy-g12a-usb3-pcie",
> + .of_match_table = phy_g12a_usb3_pcie_of_match,
> + },
> +};
> +module_platform_driver(phy_g12a_usb3_pcie_driver);
> +
> +MODULE_AUTHOR("Neil Armstrong <narmstrong@...libre.com>");
> +MODULE_DESCRIPTION("Amlogic G12A USB3 + PCIE Combo PHY driver");
> +MODULE_LICENSE("GPL v2");
>
Powered by blists - more mailing lists