Message-ID: <20190409220040.3sx456gefmjq3t3g@core.my.home>
Date:   Wed, 10 Apr 2019 00:00:40 +0200
From:   Ondřej Jirman <megous@...ous.com>
To:     Maxime Ripard <maxime.ripard@...tlin.com>
Cc:     Chen-Yu Tsai <wens@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        devicetree <devicetree@...r.kernel.org>,
        Stephen Boyd <sboyd@...nel.org>,
        Michael Turquette <mturquette@...libre.com>,
        linux-kernel <linux-kernel@...r.kernel.org>,
        Paul Kocialkowski <paul.kocialkowski@...tlin.com>,
        Chen-Yu Tsai <wens@...e.org>, Rob Herring <robh+dt@...nel.org>,
        Yong Deng <yong.deng@...ewell.com>,
        Mauro Carvalho Chehab <mchehab@...nel.org>,
        linux-clk <linux-clk@...r.kernel.org>,
        linux-arm-kernel <linux-arm-kernel@...ts.infradead.org>,
        Linux Media Mailing List <linux-media@...r.kernel.org>
Subject: Re: [PATCH 4/6] ARM: dts: sun8i: a83t: Add device node for CSI
 (Camera Sensor Interface)

On Tue, Apr 09, 2019 at 10:28:18AM +0200, Maxime Ripard wrote:
> On Tue, Apr 09, 2019 at 04:07:34PM +0800, Chen-Yu Tsai wrote:
> > On Tue, Apr 9, 2019 at 3:58 PM Maxime Ripard <maxime.ripard@...tlin.com> wrote:
> > > On Tue, Apr 09, 2019 at 12:57:42AM +0800, Chen-Yu Tsai wrote:
> > > > From: Chen-Yu Tsai <wens@...e.org>
> > > >
> > > > The A83T SoC has a camera sensor interface (known as CSI in Allwinner
> > > > lingo), which is similar to the one found on the A64 and H3. The only
> > > > difference seems to be that support of MIPI CSI through a connected
> > > > MIPI CSI-2 bridge.
> > > >
> > > > Add a device node for it, and pinctrl nodes for the commonly used MCLK
> > > > and 8-bit parallel interface. The property /omit-if-no-ref/ is added to
> > > > the pinctrl nodes to keep the device tree blob size down if they are
> > > > unused.
> > > >
> > > > Signed-off-by: Chen-Yu Tsai <wens@...e.org>
> > > > ---
> > > >  arch/arm/boot/dts/sun8i-a83t.dtsi | 31 +++++++++++++++++++++++++++++++
> > > >  1 file changed, 31 insertions(+)
> > > >
> > > > diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
> > > > index f739b88efb53..0c52f945fd5f 100644
> > > > --- a/arch/arm/boot/dts/sun8i-a83t.dtsi
> > > > +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
> > > > @@ -682,6 +682,20 @@
> > > >                       #interrupt-cells = <3>;
> > > >                       #gpio-cells = <3>;
> > > >
> > > > +                     /omit-if-no-ref/
> > > > +                     csi_8bit_parallel_pins: csi-8bit-parallel-pins {
> > > > +                             pins = "PE0", "PE2", "PE3", "PE6", "PE7",
> > > > +                                    "PE8", "PE9", "PE10", "PE11",
> > > > +                                    "PE12", "PE13";
> > > > +                             function = "csi";
> > > > +                     };
> > > > +
> > > > +                     /omit-if-no-ref/
> > > > +                     csi_mclk_pin: csi-mclk-pin {
> > > > +                             pins = "PE1";
> > > > +                             function = "csi";
> > > > +                     };
> > > > +
> > > >                       emac_rgmii_pins: emac-rgmii-pins {
> > > >                               pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
> > > >                                      "PD11", "PD12", "PD13", "PD14", "PD18",
> > > > @@ -994,6 +1008,23 @@
> > > >                       interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
> > > >               };
> > > >
> > > > +             csi: camera@...0000 {
> > > > +                     compatible = "allwinner,sun8i-a83t-csi";
> > > > +                     reg = <0x01cb0000 0x1000>;
> > > > +                     interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > > > +                     clocks = <&ccu CLK_BUS_CSI>,
> > > > +                              <&ccu CLK_CSI_SCLK>,
> > > > +                              <&ccu CLK_DRAM_CSI>;
> > > > +                     clock-names = "bus", "mod", "ram";
> > > > +                     resets = <&ccu RST_BUS_CSI>;
> > > > +                     status = "disabled";
> > > > +
> > > > +                     csi_in: port {
> > > > +                             #address-cells = <1>;
> > > > +                             #size-cells = <0>;
> > >
> > > If we expect a single enpoint, then we don't need the address-cells
> > > and size-cells properties.
> >
> > I wouldn't bet on anything. The way the Q8 tablets did front/back cameras
> > is kind of genius if not very hacky. They have two "identical" sensors
> > on the same I2C bus and CSI bus, with shared reset line but separate
> > shutdown lines. Since they are identical, they also have the same I2C
> > address. I haven't figured out how to model this in the device tree.
> >
> > The point is, it's perfectly possible to have two or more sensors use
> > the same controller, provided only one be active at a time.
> 
> Right, but I guess the common case would be to have a single sensor,
> where that wouldn't be needed.
> 
> In odd cases, we can always specify it in the DTS, and if it becomes
> common enough, we can move it to the DTSI.

I'm planning on having two sensors there, in a less arcane setup,
though - no shared resets, and different I2C addresses.

Anyway, I can confirm that CSI driver works fine on A83T with just
a DTSI patch, even without the clock patch in this series. I've been
running it for quite a while that way without any issues (different
camera chip than the ones being used by wens).

regards,
	o.

> Maxime
> 
> --
> Maxime Ripard, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com



> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@...ts.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Powered by blists - more mailing lists