| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAO=notySsUwTXuMfBjzo6evJyvAWMeCp1doyY2tyddFEp6i7yA@mail.gmail.com>
Date: Fri, 12 Apr 2019 16:30:27 -0700
From: Patrick Venture <venture@...gle.com>
To: Guenter Roeck <linux@...ck-us.net>
Cc: jdelvare@...e.com, corbet@....net,
Maxim Sloyko <maxims@...gle.com>, linux-hwmon@...r.kernel.org,
linux-doc@...r.kernel.org,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v3] hwmon: (pmbus/ir38064): Add driver for Infineon
IR38064 Voltage Regulator
On Fri, Apr 12, 2019 at 3:15 PM Guenter Roeck <linux@...ck-us.net> wrote:
>
> On 4/12/19 1:37 PM, Patrick Venture wrote:
> > From: Maxim Sloyko <maxims@...gle.com>
> >
> > Add the pmbus driver for the Infineon ir38064 voltage regulator.
> >
> > VOUT_MODE is not supported by the device. The driver fakes linear16
> > mode with exponent value -8.
> >
> > The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however
> > this driver does not enable them.
> >
>
> I meant to add this into the driver as comment (where people can see it
> going forward). Never mind, I'll apply the patch and add it myself.
Sorry, I definitely misunderstood your intent. Thanks for handling it.
>
> Guenter
>
> > Signed-off-by: Maxim Sloyko <maxims@...gle.com>
> > Signed-off-by: Patrick Venture <venture@...gle.com>
> > ---
> > v3:
> > - Updated commit message to indicate behaviors.
> > v2:
> > - Cleaned up weird tabbing behavior in doc.
> > v1:
> > - Initial patchset.
> > ---
> > Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++
> > drivers/hwmon/pmbus/Kconfig | 9 +++++
> > drivers/hwmon/pmbus/Makefile | 1 +
> > drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++
> > 4 files changed, 134 insertions(+)
> > create mode 100644 Documentation/hwmon/ir38064
> > create mode 100644 drivers/hwmon/pmbus/ir38064.c
> >
> > diff --git a/Documentation/hwmon/ir38064 b/Documentation/hwmon/ir38064
> > new file mode 100644
> > index 0000000000000..618779a329da0
> > --- /dev/null
> > +++ b/Documentation/hwmon/ir38064
> > @@ -0,0 +1,64 @@
> > +Kernel driver ir38064
> > +=====================
> > +
> > +Supported chips:
> > + * Infineon IR38064
> > + Prefix: 'ir38064'
> > + Addresses scanned: -
> > + Datasheet: Publicly available at the Infineon webiste
> > + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
> > +
> > +Datasheet is not publicly available.
> > +
> > +
> > +Authors:
> > + Maxim Sloyko <maxims@...gle.com>
> > + Patrick Venture <venture@...gle.com>
> > +
> > +Description
> > +-----------
> > +
> > +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter.
> > +
> > +Usage Notes
> > +-----------
> > +
> > +This driver does not probe for PMBus devices. You will have to instantiate
> > +devices explicitly.
> > +
> > +Sysfs attributes
> > +----------------
> > +
> > +curr1_label "iout1"
> > +curr1_input Measured output current
> > +curr1_crit Critical maximum current
> > +curr1_crit_alarm Current critical high alarm
> > +curr1_max Maximum current
> > +curr1_max_alarm Current high alarm
> > +
> > +in1_label "vin"
> > +in1_input Measured input voltage
> > +in1_crit Critical maximum input voltage
> > +in1_crit_alarm Input voltage critical high alarm
> > +in1_min Minimum input voltage
> > +in1_min_alarm Input voltage low alarm
> > +
> > +in2_label "vout1"
> > +in2_input Measured output voltage
> > +in2_lcrit Critical minimum output voltage
> > +in2_lcrit_alarm Output voltage critical low alarm
> > +in2_crit Critical maximum output voltage
> > +in2_crit_alarm Output voltage critical high alarm
> > +in2_max Maximum output voltage
> > +in2_max_alarm Output voltage high alarm
> > +in2_min Minimum output voltage
> > +in2_min_alarm Output voltage low alarm
> > +
> > +power1_label "pout1"
> > +power1_input Measured output power
> > +
> > +temp1_input Measured temperature
> > +temp1_crit Critical high temperature
> > +temp1_crit_alarm Chip temperature critical high alarm
> > +temp1_max Maximum temperature
> > +temp1_max_alarm Chip temperature high alarm
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 629cb45f8557a..de87abab990e5 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -54,6 +54,15 @@ config SENSORS_IR35221
> > This driver can also be built as a module. If so, the module will
> > be called ir35521.
> >
> > +config SENSORS_IR38064
> > + tristate "Infineon IR38064"
> > + help
> > + If you say yes here you get hardware monitoring support for Infineon
> > + IR38064.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called ir38064.
> > +
> > config SENSORS_LM25066
> > tristate "National Semiconductor LM25066 and compatibles"
> > help
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index ea0e39518c216..7d1fa6b3c8c93 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o
> > obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
> > obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
> > obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
> > +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o
> > obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
> > obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
> > obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
> > diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c
> > new file mode 100644
> > index 0000000000000..4b957ebb6fa71
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/ir38064.c
> > @@ -0,0 +1,60 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Hardware monitoring driver for Infineon IR38064
> > + *
> > + * Copyright (c) 2017 Google Inc
> > + *
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include "pmbus.h"
> > +
> > +static struct pmbus_driver_info ir38064_info = {
> > + .pages = 1,
> > + .format[PSC_VOLTAGE_IN] = linear,
> > + .format[PSC_VOLTAGE_OUT] = direct,
> > + .format[PSC_CURRENT_OUT] = linear,
> > + .format[PSC_POWER] = linear,
> > + .format[PSC_TEMPERATURE] = linear,
> > + .m[PSC_VOLTAGE_OUT] = 256,
> > + .b[PSC_VOLTAGE_OUT] = 0,
> > + .R[PSC_VOLTAGE_OUT] = 0,
> > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
> > + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
> > + | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
> > + | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT
> > + | PMBUS_HAVE_POUT,
> > +};
> > +
> > +static int ir38064_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + return pmbus_do_probe(client, id, &ir38064_info);
> > +}
> > +
> > +static const struct i2c_device_id ir38064_id[] = {
> > + {"ir38064", 0},
> > + {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, ir38064_id);
> > +
> > +/* This is the driver that will be inserted */
> > +static struct i2c_driver ir38064_driver = {
> > + .driver = {
> > + .name = "ir38064",
> > + },
> > + .probe = ir38064_probe,
> > + .remove = pmbus_do_remove,
> > + .id_table = ir38064_id,
> > +};
> > +
> > +module_i2c_driver(ir38064_driver);
> > +
> > +MODULE_AUTHOR("Maxim Sloyko <maxims@...gle.com>");
> > +MODULE_DESCRIPTION("PMBus driver for Infineon IR38064");
> > +MODULE_LICENSE("GPL");
> >
>
Powered by blists - more mailing lists