| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAO=notw7qnRtZBmi-Ew7OCOjTSw5nz4kBRA+eeUB_KYyeAkHPQ@mail.gmail.com>
Date: Wed, 24 Apr 2019 07:16:17 -0700
From: Patrick Venture <venture@...gle.com>
To: Andrew Peng <pengms1@...ovo.com>
Cc: Benjamin Fair <benjaminfair@...gle.com>,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>,
linux-aspeed@...ts.ozlabs.org,
"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE"
<linux-arm-kernel@...ts.infradead.org>, devicetree@...r.kernel.org,
Andrew Jeffery <andrew@...id.au>,
Mark Rutland <mark.rutland@....com>,
Rob Herring <robh+dt@...nel.org>,
Lisa YJ19 Liu <liuyj19@...ovo.com>,
Duke KH Du <dukh@...ovo.com>,
Yonghui YH21 Liu <liuyh21@...ovo.com>,
Harry Sung1 <hsung1@...ovo.com>, Joel Stanley <joel@....id.au>,
OpenBMC Maillist <openbmc@...ts.ozlabs.org>
Subject: Re: [PATCH v3] ARM: dts: aspeed: Adding Lenovo Hr630 BMC
On Wed, Apr 24, 2019 at 5:29 AM Andrew Peng <pengms1@...ovo.com> wrote:
>
> Initial introduction of Lenovo Hr630 family equipped with
> Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
> with a ASPEED ast2500 BMC manufactured by Lenovo.
> Specifically, This adds the Hr630 platform device tree file
> used by the Hr630 BMC machines.
>
> This also adds an entry of Hr630 device tree file in Makefile
>
> Signed-off-by: Andrew Peng <pengms1@...ovo.com>
> Signed-off-by: Yonghui Liu <liuyh21@...ovo.com>
> Signed-off-by: Lisa Liu <liuyj19@...ovo.com>
> ---
> Changes in v3:
> - revise i2c switch aliases name.
> Changes in v2:
> - add i2c switch aliases name.
> - remove the unused eeprom device from DT file.
> - remove "Licensed under..." sentence.
>
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 886 ++++++++++++++++++++++++++
> 2 files changed, 888 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index f4f5aea..375e53b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1261,4 +1261,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-opp-witherspoon.dtb \
> aspeed-bmc-opp-zaius.dtb \
> aspeed-bmc-portwell-neptune.dtb \
> - aspeed-bmc-quanta-q71l.dtb
> + aspeed-bmc-quanta-q71l.dtb \
> + aspeed-bmc-lenovo-hr630.dtb
> diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> new file mode 100644
> index 0000000..5c45523
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> @@ -0,0 +1,886 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Device Tree file for Lenovo Hr630 platform
> + *
> + * Copyright (C) 2019-present Lenovo
> + */
> +
> +/dts-v1/;
> +
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "HR630 BMC";
> + compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
> +
> + aliases {
> + pca9545_i2c0 = &i2c_rbp;
> + pca9545_i2c1 = &i2c_fbp1;
> + pca9545_i2c2 = &i2c_fbp2;
> + pca9545_i2c3 = &i2c_fbp3;
> + };
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
> + };
> +
> + memory@...00000 {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + flash_memory: region@...00000 {
> + no-map;
> + reg = <0x98000000 0x00100000>; /* 1M */
> + };
> +
> + gfx_memory: framebuffer {
> + size = <0x01000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + heartbeat {
> + gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
> + };
> +
> + fault {
> + gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
> + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
> + <&adc 8>, <&adc 9>, <&adc 10>,
> + <&adc 12>, <&adc 13>, <&adc 14>;
> + };
> +
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout.dtsi"
> + };
> +};
> +
> +&lpc_ctrl {
> + status = "okay";
> + memory-region = <&flash_memory>;
> + flash = <&spi1>;
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart5 {
> + status = "okay";
> +};
> +
> +&vuart {
> + status = "okay";
> +};
> +
> +&ibt {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii1_default>;
> + use-ncsi;
> +};
> +
> +&mac1 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
> +};
> +
> +&adc {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> + /* temp1 inlet */
> + tmp75@4e {
> + compatible = "national,lm75";
> + reg = <0x4e>;
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> + /* temp2 outlet */
> + tmp75@4d {
> + compatible = "national,lm75";
> + reg = <0x4d>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> + /* Slot 0,
> + * Slot 1,
> + * Slot 2,
> + * Slot 3
> + */
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9545";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect; /* may use mux@70 next. */
It's fine to leave mux-idle-disconnect, however the two muxes you're
worried about aren't competing under the same bus. This one lives
under i2c6 and the other i2c7, so they shouldn't interfere with each
other. Does that make sense? I missed this before because the window
only let me see part of a thing so I didn't see both in the same view
until I opened the patch in patchworks.
> +
> + i2c_rbp: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c_fbp1: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c_fbp2: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c_fbp3: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + /* Slot 0,
> + * Slot 1,
> + * Slot 2,
> + * Slot 3
> + */
> + i2c-switch@76 {
> + compatible = "nxp,pca9546";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect; /* may use mux@76 next. */
> +
> + i2c_riser2: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c_pcie4: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c_riser1: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c_ocp: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c8 {
> + status = "okay";
> +
> + eeprom@57 {
> + compatible = "atmel,24c256";
> + reg = <0x57>;
> + pagesize = <16>;
> + };
> +};
> +
> +&i2c9 {
> + status = "okay";
> +};
> +
> +&i2c10 {
> + status = "okay";
> +};
> +
> +&i2c11 {
> + status = "okay";
> +};
> +
> +&i2c12 {
> + status = "okay";
> +};
> +
> +/*
> + * Enable port A as device (via the virtual hub) and port B as
> + * host by default on the eval board. This can be easily changed
> + * by replacing the override below with &ehci0 { ... } to enable
> + * host on both ports.
> + */
> +&vhub {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&uhci {
> + status = "okay";
> +};
> +
> +&gfx {
> + status = "okay";
> + memory-region = <&gfx_memory>;
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default
> + &pinctrl_pwm1_default
> + &pinctrl_pwm2_default
> + &pinctrl_pwm3_default
> + &pinctrl_pwm4_default
> + &pinctrl_pwm5_default
> + &pinctrl_pwm6_default>;
> +
> + fan@0 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x00>;
> + };
> +
> + fan@1 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x01>;
> + };
> +
> + fan@2 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x02>;
> + };
> +
> + fan@3 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x03>;
> + };
> +
> + fan@4 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> + };
> +
> + fan@5 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> + };
> +
> + fan@6 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> + };
> +
> + fan@7 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> + };
> +
> + fan@8 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> + };
> +
> + fan@9 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> + };
> +
> + fan@10 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> + };
> +
> + fan@11 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> + };
> +
> + fan@12 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> + };
> +
> + fan@13 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> + };
> +};
> +
> +&gpio {
> +
> + pin_gpio_a0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MAC1_INT_N";
> + };
> +
> + pin_gpio_a1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MEZZ_C_PRESENT_N";
> + };
> +
> + pin_gpio_a2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_PRST";
> + };
> +
> + pin_gpio_a3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_PRST";
> + };
> +
> + pin_gpio_b5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "IRQ_BMC_PCH_SMI_LPC_N";
> + };
> +
> + pin_gpio_f0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "IRQ_BMC_PCH_NMI_R";
> + };
> +
> + pin_gpio_f1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU1_DISABLE_COD_N";
> + };
> +
> + pin_gpio_f2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "SMB_LAN_ALERT_N_MEZZ";
> + };
> +
> + pin_gpio_f3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_BUS0_RST_OUT_N";
> + };
> +
> + pin_gpio_f4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "FM_SKT0_FAULT_LED";
> + };
> +
> + pin_gpio_f5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "FM_SKT1_FAULT_LED";
> + };
> +
> + pin_gpio_f6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_BMC_CPLD_NMI";
> + };
> +
> + pin_gpio_f7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_ALERT_N";
> + };
> +
> + pin_gpio_g0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU_ERR2_LVT3_N";
> + };
> +
> + pin_gpio_g1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU_MSMI_CATERR_LVT3_N";
> + };
> +
> + pin_gpio_g2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PCH_BMC_THERMTRIP_N";
> + };
> +
> + pin_gpio_g3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_I2C_BUS7_INT_N";
> + };
> +
> + pin_gpio_g4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "FAN_PWR_CTL_N";
> + };
> +
> + pin_gpio_g5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "NFC_FD_N";
> + };
> +
> + pin_gpio_g6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_NMI_EVENT_N";
> + };
> +
> + pin_gpio_g7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "RST_BMC_PCIE_I2CMUX_N";
> + };
> +
> + pin_gpio_h0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_EPOW_N_R";
> + };
> +
> + pin_gpio_h1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_EPOW_N_R";
> + };
> +
> + pin_gpio_h2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PSU1_FFS_N_R";
> + };
> +
> + pin_gpio_h3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PSU2_FFS_N_R";
> + };
> +
> + pin_gpio_h4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_THROTTLE_N_R";
> + };
> +
> + pin_gpio_h5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_THROTTLE_N_R";
> + };
> +
> + pin_gpio_h6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_SMB_RESET_N";
> + };
> +
> + pin_gpio_h7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_SMB_RESET_N";
> + };
> +
> + pin_gpio_i1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FP_PWR_BTN_N";
> + };
> +
> + pin_gpio_i2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BIOS_RCVR_N";
> + };
> +
> + pin_gpio_i3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_INTRUDED_COVER";
> + };
> +
> + pin_gpio_j2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_BIOS_UPDATE_N";
> + };
> +
> + pin_gpio_j3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "RST_BMC_HDD_I2CMUX_N";
> + };
> +
> + pin_gpio_q4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MEZZ_A_PRESENT_N";
> + };
> +
> + pin_gpio_q5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "VGA_FRONT_PRES_N";
> + };
> +
> + pin_gpio_q6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "I2C_RISER1_INT_N";
> + };
> +
> + pin_gpio_q7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "NCSI_CABLE_DET_N";
> + };
> +
> + pin_gpio_r0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FP_RST_BTN_N";
> + };
> +
> + pin_gpio_r2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG1_DETECT_N";
> + };
> +
> + pin_gpio_r3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG2_DETECT_N";
> + };
> +
> + pin_gpio_r4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG3_DETECT_N";
> + };
> +
> + pin_gpio_r5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "VIDEO_CABLE_DETECT_N";
> + };
> +
> + pin_gpio_s0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_PS_RAPIDON_WAKE_R_N";
> + };
> +
> + pin_gpio_s1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HOST_TPM_PP_BUF";
> + };
> +
> + pin_gpio_s2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_VGA_SW";
> + };
> +
> + pin_gpio_s3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_SML0_ALERT_MUX_N";
> + };
> +
> + pin_gpio_s4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
> + output;
> + line-name = "VBAT_EN_N";
> + };
> +
> + pin_gpio_s5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_4";
> + };
> +
> + pin_gpio_s6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PU_BMC_GPIOS6";
> + };
> +
> + pin_gpio_s7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "I2C_BUS7_RESET_N";
> + };
> +
> + pin_gpio_y0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_NCSI_MUX_CTL_S0";
> + };
> +
> + pin_gpio_y1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_NCSI_MUX_CTL_S1";
> + };
> +
> + pin_gpio_y2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "UID_ALERT_N";
> + };
> +
> + pin_gpio_z0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_RISER2_INT_N";
> + };
> +
> + pin_gpio_z2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_RISER2_RESET_N";
> + };
> +
> + pin_gpio_z3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "FM_BMC_PCH_SCI_LPC_N";
> + };
> +
> + pin_gpio_z4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_17";
> + };
> +
> + pin_gpio_z6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_20";
> + };
> +
> + pin_gpio_z7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_POST_CMPLT_N";
> + };
> +
> + pin_gpio_aa0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "HOST_BMC_USB_SEL";
> + };
> +
> + pin_gpio_aa1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_ALERT_N";
> + };
> +
> + pin_gpio_aa2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PVCCIN_CPU0_PWR_IN_ALERT_N";
> + };
> +
> + pin_gpio_aa3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PVCCIN_CPU1_PWR_IN_ALERT_N";
> + };
> +
> + pin_gpio_aa4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "USB_CABLE_DETECT_N";
> + };
> +
> + pin_gpio_aa5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_BUS1_RST_OUT_N";
> + };
> +
> + pin_gpio_aa6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_SMI_ACTIVE_N";
> + };
> +
> + pin_gpio_aa7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_BIOS_POST_CMPLT_N";
> + };
> +
> + pin_gpio_ab0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_TPM_MOD_PRES_N";
> + };
> +
> + pin_gpio_ab1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FORCE_NMI_SW_FPGA_N";
> + };
> +
> + pin_gpio_ab2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "1U_2U_PCBA_SEL_R";
> + };
> +
> + pin_gpio_ab3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "INTRUDED_PRES_N";
> + };
> +};
This is my last comment.
Thanks,
Patrick
> --
> 2.7.4
>
Powered by blists - more mailing lists