linux-kernel - Re: [RFC PATCH 2/2] mmc: sdhci: Quirk for AMD SDHC Device 0x7906

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <08c3dc49-f5cb-401d-b900-12879f469728@intel.com>
Date:   Thu, 2 May 2019 09:32:16 +0300
From:   Adrian Hunter <adrian.hunter@...el.com>
To:     Raul E Rangel <rrangel@...omium.org>, linux-mmc@...r.kernel.org,
        "Agrawal, Nitesh-kumar" <Nitesh-kumar.Agrawal@....com>
Cc:     djkurtz@...omium.org, linux-kernel@...r.kernel.org,
        Ulf Hansson <ulf.hansson@...aro.org>,
        Shyam Sundar S K <Shyam-sundar.S-k@....com>,
        "Sen, Pankaj" <Pankaj.Sen@....com>,
        "Shah, Nehal-bakulchandra" <Nehal-bakulchandra.Shah@....com>
Subject: Re: [RFC PATCH 2/2] mmc: sdhci: Quirk for AMD SDHC Device 0x7906

Cc: some AMD people

On 1/05/19 8:54 PM, Raul E Rangel wrote:
> AMD SDHC 0x7906 requires a hard reset to clear all internal state.
> Otherwise it can get into a bad state where the DATA lines are always
> read as zeros.
> 
> This change requires firmware that can transition the device into
> D3Cold for it to work correctly. If the firmware does not support
> transitioning to D3Cold then the power state transitions are a no-op.
> 
> Signed-off-by: Raul E Rangel <rrangel@...omium.org>
> ---
> 
>  drivers/mmc/host/sdhci-pci-core.c | 51 ++++++++++++++++++++++++++++++-
>  1 file changed, 50 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-core.c b/drivers/mmc/host/sdhci-pci-core.c
> index 99b0fec2836b..532fbcbd373b 100644
> --- a/drivers/mmc/host/sdhci-pci-core.c
> +++ b/drivers/mmc/host/sdhci-pci-core.c
> @@ -25,6 +25,7 @@
>  #include <linux/mmc/mmc.h>
>  #include <linux/scatterlist.h>
>  #include <linux/io.h>
> +#include <linux/iopoll.h>
>  #include <linux/gpio.h>
>  #include <linux/pm_runtime.h>
>  #include <linux/mmc/slot-gpio.h>
> @@ -1498,11 +1499,59 @@ static int amd_probe(struct sdhci_pci_chip *chip)
>  	return 0;
>  }
>  
> +static u32 sdhci_read_present_state(struct sdhci_host *host)
> +{
> +	return sdhci_readl(host, SDHCI_PRESENT_STATE);
> +}
> +
> +void amd_sdhci_reset(struct sdhci_host *host, u8 mask)
> +{
> +	struct sdhci_pci_slot *slot = sdhci_priv(host);
> +	struct pci_dev *pdev = slot->chip->pdev;
> +	u32 present_state;
> +
> +	/*
> +	 * SDHC 0x7906 requires a hard reset to clear all internal state.
> +	 * Otherwise it can get into a bad state where the DATA lines are always
> +	 * read as zeros.
> +	 */
> +	if (pdev->device == 0x7906 && (mask & SDHCI_RESET_ALL)) {
> +		pci_clear_master(pdev);
> +
> +		pci_save_state(pdev);
> +
> +		pci_set_power_state(pdev, PCI_D3cold);
> +		pr_debug("%s: power_state=%u\n", mmc_hostname(host->mmc),
> +			pdev->current_state);
> +		pci_set_power_state(pdev, PCI_D0);
> +
> +		pci_restore_state(pdev);
> +
> +		/*
> +		 * SDHCI_RESET_ALL says the card detect logic should not be
> +		 * reset, but since we need to reset the entire controller
> +		 * we should wait until the card detect logic has stabilized.
> +		 *
> +		 * This normally takes about 40ms.
> +		 */
> +		readx_poll_timeout(
> +			sdhci_read_present_state,
> +			host,
> +			present_state,
> +			present_state & SDHCI_CD_STABLE,
> +			10000,
> +			100000
> +		);
> +	}
> +
> +	return sdhci_reset(host, mask);
> +}
> +
>  static const struct sdhci_ops amd_sdhci_pci_ops = {
>  	.set_clock			= sdhci_set_clock,
>  	.enable_dma			= sdhci_pci_enable_dma,
>  	.set_bus_width			= sdhci_set_bus_width,
> -	.reset				= sdhci_reset,
> +	.reset				= amd_sdhci_reset,
>  	.set_uhs_signaling		= sdhci_set_uhs_signaling,
>  };
>  
>