[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <f8486dab-f95b-a4b1-36f2-89b98086d0cb@nvidia.com>
Date: Thu, 2 May 2019 14:36:10 +0100
From: Jon Hunter <jonathanh@...dia.com>
To: Sameer Pujar <spujar@...dia.com>, <vkoul@...nel.org>,
<dan.j.williams@...el.com>, <robh+dt@...nel.org>,
<mark.rutland@....com>
CC: <thierry.reding@...il.com>, <ldewangan@...dia.com>,
<dmaengine@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-tegra@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 0/6] Add support for Tegra186/Tegra194 and generic fixes
On 02/05/2019 13:55, Sameer Pujar wrote:
> Audio DMA(ADMA) interface is a gateway in the AHUB for facilitating DMA
> transfers between memory and all of its clients. Currently the driver
> supports Tegra210 based platforms. This series adds support for Tegra186
> and Tegra194 based platforms and fixes few functional issues.
>
> Patches in the series are classified into three categories,
> 1. Add support for Tegra186 and Tegra194
> 2. Add DMA pause/resume feature
> 3. Fixes common to differernt Tegra generations
>
> Below change log describes the patches in detail.
>
> Change log:
> =====================================
> v1
> ----
> The series can be classified into 3 categories,
> 1. Add support for Tegra186 and Tegra194
> [Patch 1/6] dmaengine: tegra210-adma: prepare for supporting newer
> Tegra chips
> * The support was there only for Tegra210
> * This is a preparation for adding support for newer Tegra chips
> * chip_data is enhanced to support differences between Tegra210 and
> Tegra186/Tegra194
> [Patch 2/6] Documentation: DT: Add compatibility binding for Tegra186
> * New compatibility string is required for driver to work for
> Tegra186 and Tegra194. Hence new compatibility is introduced.
> * Tegra194 can use the same compatibility as Tegra186
> [Patch 3/6] dmaengine: tegra210-adma: add support for Tegra186/
> Tegra194
> * Populates chip specific information for Tegra186
> * There is a difference in the way ADMA CH_CONFIG registers are
> encoded for Tegra210 and Tegra186. Added helper fucntions to
> support different versions of burst size configuration
>
> 2. Add DMA pause/resume feature
> [Patch 4/6] dmaengine: tegra210-adma: add pause/resume support
> * Adds support for ADMA pause/resume, otherwise audio loss was seen
> during continuous pause/resume of audio playback.
>
> 3. Fixes common to differernt Tegra generations
> [Patch 5/6] dmaengine: tegra210-dma: free dma controller in remove()
> * Fixes kernel panic observed during driver reload. DMA controller
> needs to be freed when driver is unloaded
> [Patch 6/6] dmaengine: tegra210-adma: restore channel status
> * Fixes resume across system suspend. If the channel state is not
> restored, the transfers won't resume from the state from where it
> was left during suspend entry. In this case, audio playback did
> not resume properly once system exited from low power state.
>
> ===============================
> Sameer Pujar (6):
> dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
> Documentation: DT: Add compatibility binding for Tegra186
> dmaengine: tegra210-adma: add support for Tegra186/Tegra194
> dmaengine: tegra210-adma: add pause/resume support
> dmaengine: tegra210-dma: free dma controller in remove()
> dmaengine: tegra210-adma: restore channel status
>
> .../bindings/dma/nvidia,tegra210-adma.txt | 4 +-
> drivers/dma/tegra210-adma.c | 232 +++++++++++++++++----
> 2 files changed, 193 insertions(+), 43 deletions(-)
>
Thanks!
For the series ...
Reviewed-by: Jon Hunter <jonathanh@...dia.com>
Cheers
Jon
--
nvpublic
Powered by blists - more mailing lists