| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1557036518-286348-1-git-send-email-pengms1@lenovo.com>
Date: Sun, 5 May 2019 14:08:38 +0800
From: Andrew Peng <pengms1@...ovo.com>
To: venture@...gle.com, benjaminfair@...gle.com,
linux-kernel@...r.kernel.org, linux-aspeed@...ts.ozlabs.org,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
andrew@...id.au, mark.rutland@....com, robh+dt@...nel.org
Cc: pengms1@...ovo.com, liuyj19@...ovo.com, dukh@...ovo.com,
liuyh21@...ovo.com, hsung1@...ovo.com, joel@....id.au,
openbmc@...ts.ozlabs.org
Subject: [PATCH v6] ARM: dts: aspeed: Adding Lenovo Hr630 BMC
Initial introduction of Lenovo Hr630 family equipped with
Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Lenovo.
Specifically, This adds the Hr630 platform device tree file
used by the Hr630 BMC machines.
This also adds an entry of Hr630 device tree file in Makefile
Signed-off-by: Andrew Peng <pengms1@...ovo.com>
Signed-off-by: Yonghui Liu <liuyh21@...ovo.com>
Signed-off-by: Lisa Liu <liuyj19@...ovo.com>
---
Changes in v6:
- add appropriate pinctrl property for uar1, uart2, uart3 and adc.
- remove vhub definition and comment.
- remove some GPIO definitions.
- revise Makefile according to sort alphabetically.
Changes in v5:
- revise pca9545 and pca9546 switch aliases name.
Changes in v4:
- add pca9546 switch aliases name.
Changes in v3:
- revise i2c switch aliases name.
Changes in v2:
- add i2c switch aliases name.
- remove the unused eeprom device from DT file.
- remove "Licensed under..." sentence.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 566 ++++++++++++++++++++++++++
2 files changed, 567 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aea..1276167 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1255,6 +1255,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-tiogapass.dtb \
aspeed-bmc-intel-s2600wf.dtb \
+ aspeed-bmc-lenovo-hr630.dtb \
aspeed-bmc-opp-lanyang.dtb \
aspeed-bmc-opp-palmetto.dtb \
aspeed-bmc-opp-romulus.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
new file mode 100644
index 0000000..d3695a3
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
@@ -0,0 +1,566 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for Lenovo Hr630 platform
+ *
+ * Copyright (C) 2019-present Lenovo
+ */
+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "HR630 BMC";
+ compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
+
+ aliases {
+ i2c14 = &i2c_rbp;
+ i2c15 = &i2c_fbp1;
+ i2c16 = &i2c_fbp2;
+ i2c17 = &i2c_fbp3;
+ i2c18 = &i2c_riser2;
+ i2c19 = &i2c_pcie4;
+ i2c20 = &i2c_riser1;
+ i2c21 = &i2c_ocp;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
+ };
+
+ memory@...00000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ flash_memory: region@...00000 {
+ no-map;
+ reg = <0x98000000 0x00100000>; /* 1M */
+ };
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ heartbeat {
+ gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
+ };
+
+ fault {
+ gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+ <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+ <&adc 8>, <&adc 9>, <&adc 10>,
+ <&adc 12>, <&adc 13>, <&adc 14>;
+ };
+
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout.dtsi"
+ };
+};
+
+&lpc_ctrl {
+ status = "okay";
+ memory-region = <&flash_memory>;
+ flash = <&spi1>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default>;
+};
+
+&uart2 {
+ /* Rear RS-232 connector */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd2_default
+ &pinctrl_rxd2_default
+ &pinctrl_nrts2_default
+ &pinctrl_ndtr2_default
+ &pinctrl_ndsr2_default
+ &pinctrl_ncts2_default
+ &pinctrl_ndcd2_default
+ &pinctrl_nri2_default>;
+};
+
+&uart3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd3_default
+ &pinctrl_rxd3_default>;
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&ibt {
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii1_default>;
+ use-ncsi;
+};
+
+&mac1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&adc {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default
+ &pinctrl_adc1_default
+ &pinctrl_adc2_default
+ &pinctrl_adc3_default
+ &pinctrl_adc4_default
+ &pinctrl_adc5_default
+ &pinctrl_adc6_default
+ &pinctrl_adc7_default
+ &pinctrl_adc8_default
+ &pinctrl_adc9_default
+ &pinctrl_adc10_default
+ &pinctrl_adc12_default
+ &pinctrl_adc13_default
+ &pinctrl_adc14_default>;
+};
+
+&i2c0 {
+ status = "okay";
+ /* temp1 inlet */
+ tmp75@4e {
+ compatible = "national,lm75";
+ reg = <0x4e>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ /* temp2 outlet */
+ tmp75@4d {
+ compatible = "national,lm75";
+ reg = <0x4d>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+ /* Slot 0,
+ * Slot 1,
+ * Slot 2,
+ * Slot 3
+ */
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9545";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect; /* may use mux@70 next. */
+
+ i2c_rbp: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c_fbp1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c_fbp2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c_fbp3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ /* Slot 0,
+ * Slot 1,
+ * Slot 2,
+ * Slot 3
+ */
+ i2c-switch@76 {
+ compatible = "nxp,pca9546";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect; /* may use mux@76 next. */
+
+ i2c_riser2: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c_pcie4: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c_riser1: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c_ocp: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ eeprom@57 {
+ compatible = "atmel,24c256";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c12 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&uhci {
+ status = "okay";
+};
+
+&gfx {
+ status = "okay";
+ memory-region = <&gfx_memory>;
+};
+
+&pwm_tacho {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default
+ &pinctrl_pwm1_default
+ &pinctrl_pwm2_default
+ &pinctrl_pwm3_default
+ &pinctrl_pwm4_default
+ &pinctrl_pwm5_default
+ &pinctrl_pwm6_default>;
+
+ fan@0 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+ };
+
+ fan@1 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+ };
+
+ fan@2 {
+ reg = <0x01>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+ };
+
+ fan@3 {
+ reg = <0x01>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+ };
+
+ fan@4 {
+ reg = <0x02>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+ };
+
+ fan@5 {
+ reg = <0x02>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+ };
+
+ fan@6 {
+ reg = <0x03>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+ };
+
+ fan@7 {
+ reg = <0x03>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+ };
+
+ fan@8 {
+ reg = <0x04>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+ };
+
+ fan@9 {
+ reg = <0x04>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+ };
+
+ fan@10 {
+ reg = <0x05>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+ };
+
+ fan@11 {
+ reg = <0x05>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+ };
+
+ fan@12 {
+ reg = <0x06>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+ };
+
+ fan@13 {
+ reg = <0x06>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+ };
+};
+
+&gpio {
+
+ pin_gpio_b5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "IRQ_BMC_PCH_SMI_LPC_N";
+ };
+
+ pin_gpio_f0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "IRQ_BMC_PCH_NMI_R";
+ };
+
+ pin_gpio_f3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_BUS0_RST_OUT_N";
+ };
+
+ pin_gpio_f4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "FM_SKT0_FAULT_LED";
+ };
+
+ pin_gpio_f5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "FM_SKT1_FAULT_LED";
+ };
+
+ pin_gpio_g4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "FAN_PWR_CTL_N";
+ };
+
+ pin_gpio_g7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "RST_BMC_PCIE_I2CMUX_N";
+ };
+
+ pin_gpio_h2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PSU1_FFS_N_R";
+ };
+
+ pin_gpio_h3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PSU2_FFS_N_R";
+ };
+
+ pin_gpio_i3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_INTRUDED_COVER";
+ };
+
+ pin_gpio_j2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_BIOS_UPDATE_N";
+ };
+
+ pin_gpio_j3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "RST_BMC_HDD_I2CMUX_N";
+ };
+
+ pin_gpio_s2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_VGA_SW";
+ };
+
+ pin_gpio_s4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
+ output;
+ line-name = "VBAT_EN_N";
+ };
+
+ pin_gpio_s6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PU_BMC_GPIOS6";
+ };
+
+ pin_gpio_y0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_NCSI_MUX_CTL_S0";
+ };
+
+ pin_gpio_y1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_NCSI_MUX_CTL_S1";
+ };
+
+ pin_gpio_z0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_RISER2_INT_N";
+ };
+
+ pin_gpio_z2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_RISER2_RESET_N";
+ };
+
+ pin_gpio_z3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "FM_BMC_PCH_SCI_LPC_N";
+ };
+
+ pin_gpio_z7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_POST_CMPLT_N";
+ };
+
+ pin_gpio_aa0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "HOST_BMC_USB_SEL";
+ };
+
+ pin_gpio_aa5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_BUS1_RST_OUT_N";
+ };
+
+};
--
2.7.4
Powered by blists - more mailing lists