[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <CAFBinCAe3jd598MPLUGFEoBAOaeXovSz7_8Kn7ZMmSFvRLFSXg@mail.gmail.com>
Date: Sat, 11 May 2019 18:59:47 +0200
From: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
To: Jerome Brunet <jbrunet@...libre.com>
Cc: Kevin Hilman <khilman@...libre.com>,
linux-amlogic@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH 3/5] arm64: dts: meson: g12a: add mdio multiplexer
Hi Jerome,
On Fri, May 10, 2019 at 6:49 PM Jerome Brunet <jbrunet@...libre.com> wrote:
>
> Add the g12a mdio multiplexer which allows to connect to either
> an external phy through the SoC pins or the internal 10/100 phy
>
> Signed-off-by: Jerome Brunet <jbrunet@...libre.com>
> ---
> arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 32 +++++++++++++++++++++
> 1 file changed, 32 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> index fe0f73730525..6e9587aafb5d 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> @@ -460,6 +460,38 @@
> assigned-clock-rates = <100000000>;
> #phy-cells = <1>;
> };
> +
> + eth_phy: mdio-multiplexer@...00 {
> + compatible = "amlogic,g12a-mdio-mux";
> + reg = <0x0 0x4c000 0x0 0xa4>;
> + clocks = <&clkc CLKID_ETH_PHY>,
> + <&xtal>,
> + <&clkc CLKID_MPLL_5OM>;
I haven't noticed that before but there's a typo in the MPLL_5OM clock
definition:
the O (capital o) should be a 0 (zero).
can you fix this typo in an additional clock patch for v5.2 - then we
don't have to do it in v5.3 where this .dtsi might already use it
> + clock-names = "pclk", "clkin0", "clkin1";
> + mdio-parent-bus = <&mdio0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ext_mdio: mdio@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + int_mdio: mdio@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + internal_ephy: ethernet_phy@8 {
> + compatible = "ethernet-phy-id0180.3301",
> + "ethernet-phy-ieee802.3-c22";
please drop the compatible string and replace it with a comment (if
you feel that it's needed).
quote from Documentation/devicetree/bindings/net/phy.txt:
> If the PHY reports an incorrect ID (or none at all) then the
> "compatible" list may contain an entry with the correct PHY ID in the
> form: "ethernet-phy-idAAAA.BBBB"
I am going to send a patch for other Amlogic boards to remove any
ethernet-phy-id comaptible string
Regards
Martin
Powered by blists - more mailing lists