| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20190527111156.3539-1-tmn505@gmail.com>
Date: Mon, 27 May 2019 13:11:56 +0200
From: Tomasz Maciej Nowak <tmn505@...il.com>
To: Jason Cooper <jason@...edaemon.net>, Andrew Lunn <andrew@...n.ch>,
Gregory Clement <gregory.clement@...tlin.com>,
Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>
Cc: Konstantin Porotchkin <kostap@...vell.com>,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH] arm64: dts: marvell: add ESPRESSObin variants
This commit adds dts for different variants of ESPRESSObin board:
ESPRESSObin with soldered eMMC,
ESPRESSObin V7, compared to prior versions some passive elements changed
and ethernet ports labels positions have been reversed,
ESPRESSObin V7 with soldered eMMC.
Since most of elements are the same, one common dtsi is created and
referenced in each dts of particular variant.
Signed-off-by: Tomasz Maciej Nowak <tmn505@...il.com>
---
.../marvell/armada-3720-espressobin-emmc.dts | 42 ++++
.../armada-3720-espressobin-v7-emmc.dts | 59 ++++++
.../marvell/armada-3720-espressobin-v7.dts | 36 ++++
.../dts/marvell/armada-3720-espressobin.dts | 200 +-----------------
.../dts/marvell/armada-3720-espressobin.dtsi | 193 +++++++++++++++++
5 files changed, 331 insertions(+), 199 deletions(-)
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-espressobin-emmc.dts
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-emmc.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-emmc.dts
new file mode 100644
index 000000000000..bd9ed9dc9c3e
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-emmc.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board with eMMC
+ * Copyright (C) 2018 Marvell
+ *
+ * Romain Perier <romain.perier@...e-electrons.com>
+ * Konstantin Porotchkin <kostap@...vell.com>
+ *
+ */
+/*
+ * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.pdf
+ */
+
+#include "armada-3720-espressobin.dtsi"
+
+/ {
+ model = "Globalscale Marvell ESPRESSOBin Board (eMMC)";
+ compatible = "globalscale,espressobin-emmc", "globalscale,espressobin",
+ "marvell,armada3720", "marvell,armada3710";
+};
+
+/* U11 */
+&sdhci0 {
+ non-removable;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ marvell,xenon-emmc;
+ marvell,xenon-tun-count = <9>;
+ marvell,pad-type = "fixed-1-8v";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc_pins>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard@0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts
new file mode 100644
index 000000000000..6e876a6d9532
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board V7 with eMMC
+ * Copyright (C) 2018 Marvell
+ *
+ * Romain Perier <romain.perier@...e-electrons.com>
+ * Konstantin Porotchkin <kostap@...vell.com>
+ *
+ */
+/*
+ * Schematic available at http://wiki.espressobin.net/tiki-download_file.php?fileId=200
+ */
+
+#include "armada-3720-espressobin.dtsi"
+
+/ {
+ model = "Globalscale Marvell ESPRESSOBin Board V7 (eMMC)";
+ compatible = "globalscale,espressobin-v7-emmc", "globalscale,espressobin-v7",
+ "globalscale,espressobin", "marvell,armada3720",
+ "marvell,armada3710";
+};
+
+&switch0 {
+ ports {
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&switch0phy0>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "wan";
+ phy-handle = <&switch0phy2>;
+ };
+ };
+};
+
+/* U11 */
+&sdhci0 {
+ non-removable;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ marvell,xenon-emmc;
+ marvell,xenon-tun-count = <9>;
+ marvell,pad-type = "fixed-1-8v";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc_pins>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard@0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts
new file mode 100644
index 000000000000..0f8405d085fd
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board V7
+ * Copyright (C) 2018 Marvell
+ *
+ * Romain Perier <romain.perier@...e-electrons.com>
+ * Konstantin Porotchkin <kostap@...vell.com>
+ *
+ */
+/*
+ * Schematic available at http://wiki.espressobin.net/tiki-download_file.php?fileId=200
+ */
+
+#include "armada-3720-espressobin.dtsi"
+
+/ {
+ model = "Globalscale Marvell ESPRESSOBin Board V7";
+ compatible = "globalscale,espressobin-v7", "globalscale,espressobin",
+ "marvell,armada3720", "marvell,armada3710";
+};
+
+&switch0 {
+ ports {
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&switch0phy0>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "wan";
+ phy-handle = <&switch0phy2>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
index 6be019e1888e..1542d836c090 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
@@ -12,207 +12,9 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-espressobin.dtsi"
/ {
model = "Globalscale Marvell ESPRESSOBin Board";
compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
- };
-
- vcc_sd_reg1: regulator {
- compatible = "regulator-gpio";
- regulator-name = "vcc_sd1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
-
- gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1
- 3300000 0x0>;
- enable-active-high;
- };
-};
-
-/* J9 */
-&pcie0 {
- status = "okay";
- phys = <&comphy1 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
-};
-
-/* J6 */
-&sata {
- status = "okay";
- phys = <&comphy2 0>;
- phy-names = "sata-phy";
-};
-
-/* J1 */
-&sdhci1 {
- wp-inverted;
- bus-width = <4>;
- cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
- marvell,pad-type = "sd";
- vqmmc-supply = <&vcc_sd_reg1>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdio_pins>;
- status = "okay";
-};
-
-/* U11 */
-&sdhci0 {
- non-removable;
- bus-width = <8>;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- marvell,xenon-emmc;
- marvell,xenon-tun-count = <9>;
- marvell,pad-type = "fixed-1-8v";
-
- pinctrl-names = "default";
- pinctrl-0 = <&mmc_pins>;
-/*
- * This eMMC is not populated on all boards, so disable it by
- * default and let the bootloader enable it, if it is present
- */
- status = "disabled";
-};
-
-&spi0 {
- status = "okay";
-
- flash@0 {
- reg = <0>;
- compatible = "winbond,w25q32dw", "jedec,spi-flash";
- spi-max-frequency = <104000000>;
- m25p,fast-read;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "uboot";
- reg = <0 0x180000>;
- };
-
- partition@...000 {
- label = "ubootenv";
- reg = <0x180000 0x10000>;
- };
- };
- };
-};
-
-/* Exported on the micro USB connector J5 through an FTDI */
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
- status = "okay";
-};
-
-/*
- * Connector J17 and J18 expose a number of different features. Some pins are
- * multiplexed. This is the case for instance for the following features:
- * - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of
- * how to enable it. Beware that the signals are 1.8V TTL.
- * - I2C
- * - SPI
- * - MMC
- */
-
-/* J7 */
-&usb3 {
- status = "okay";
-};
-
-/* J8 */
-&usb2 {
- status = "okay";
-};
-
-&mdio {
- switch0: switch0@1 {
- compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- dsa,member = <0 0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <ð0>;
- phy-mode = "rgmii-id";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "wan";
- phy-handle = <&switch0phy0>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan0";
- phy-handle = <&switch0phy1>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan1";
- phy-handle = <&switch0phy2>;
- };
-
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch0phy0: switch0phy0@11 {
- reg = <0x11>;
- };
- switch0phy1: switch0phy1@12 {
- reg = <0x12>;
- };
- switch0phy2: switch0phy2@13 {
- reg = <0x13>;
- };
- };
- };
-};
-
-ð0 {
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
- phy-mode = "rgmii-id";
- status = "okay";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
new file mode 100644
index 000000000000..4a114db76bf9
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -0,0 +1,193 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board
+ * Copyright (C) 2016 Marvell
+ *
+ * Romain Perier <romain.perier@...e-electrons.com>
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ vcc_sd_reg1: regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vcc_sd1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+
+ gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ enable-active-high;
+ };
+};
+
+/* J9 */
+&pcie0 {
+ status = "okay";
+ phys = <&comphy1 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+};
+
+/* J6 */
+&sata {
+ status = "okay";
+ phys = <&comphy2 0>;
+ phy-names = "sata-phy";
+};
+
+/* J1 */
+&sdhci1 {
+ wp-inverted;
+ bus-width = <4>;
+ cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
+ marvell,pad-type = "sd";
+ vqmmc-supply = <&vcc_sd_reg1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio_pins>;
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ reg = <0>;
+ compatible = "winbond,w25q32dw", "jedec,spi-flash";
+ spi-max-frequency = <104000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0 0x180000>;
+ };
+
+ partition@...000 {
+ label = "ubootenv";
+ reg = <0x180000 0x10000>;
+ };
+ };
+ };
+};
+
+/* Exported on the micro USB connector J5 through an FTDI */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+/*
+ * Connector J17 and J18 expose a number of different features. Some pins are
+ * multiplexed. This is the case for instance for the following features:
+ * - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of
+ * how to enable it. Beware that the signals are 1.8V TTL.
+ * - I2C
+ * - SPI
+ * - MMC
+ */
+
+/* J7 */
+&usb3 {
+ status = "okay";
+};
+
+/* J8 */
+&usb2 {
+ status = "okay";
+};
+
+&mdio {
+ switch0: switch0@1 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <ð0>;
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "wan";
+ phy-handle = <&switch0phy0>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan0";
+ phy-handle = <&switch0phy1>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan1";
+ phy-handle = <&switch0phy2>;
+ };
+
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy0: switch0phy0@11 {
+ reg = <0x11>;
+ };
+ switch0phy1: switch0phy1@12 {
+ reg = <0x12>;
+ };
+ switch0phy2: switch0phy2@13 {
+ reg = <0x13>;
+ };
+ };
+ };
+};
+
+ð0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
--
2.21.0
Powered by blists - more mailing lists