lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite for Android: free password hash cracker in your pocket
[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-Id: <20190611175839.28351-1-nsaenzjulienne@suse.de>
Date:   Tue, 11 Jun 2019 19:58:32 +0200
From:   Nicolas Saenz Julienne <nsaenzjulienne@...e.de>
To:     stefan.wahren@...e.com, linux-kernel@...r.kernel.org
Cc:     mbrugger@...e.de, viresh.kumar@...aro.org, rjw@...ysocki.net,
        sboyd@...nel.org, eric@...olt.net, f.fainelli@...il.com,
        bcm-kernel-feedback-list@...adcom.com, ptesarik@...e.com,
        linux-rpi-kernel@...ts.infradead.org, ssuloev@...altech.com,
        linux-clk@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
        mturquette@...libre.com, linux-pm@...r.kernel.org,
        Nicolas Saenz Julienne <nsaenzjulienne@...e.de>
Subject: [PATCH v3 0/7] cpufreq support for Raspberry Pi

Hi all,
this aims at adding cpufreq support to the Raspberry Pi family of
boards.

The series first factors out 'pllb' from clk-bcm2385 and creates a new
clk driver that operates it over RPi's firmware interface[1]. We are
forced to do so as the firmware 'owns' the pll and we're not allowed to
change through the register interface directly as we might race with the
over-temperature and under-voltage protections provided by the firmware.

Next it creates a minimal cpufreq driver that populates the CPU's opp
table, and registers cpufreq-dt. Which is needed as the firmware
controls the max and min frequencies available.

This was tested on a RPi3b+ and RPI2b, both using multi_v7_defconfig and
arm64's defconfig.

That's all,
kind regards,
Nicolas

[1] https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface

---

Changes since v2:
  - Fixed configs to match Stefan's comments
  - Round OPP frequencies
  - Rebase onto linux-next
  - Minor cleanups & checkpatch.pl

Changes since v1:
  - Enabled by default on the whole family of devices
  - Added/Fixed module support
  - clk device now registered by firmware driver
  - raspberrypi-cpufreq device now registered by clk driver
  - Reimplemented clk rounding unsing determine_rate()
  - Enabled in configs for arm and arm64

Changes since RFC:
  - Move firmware clk device into own driver

Nicolas Saenz Julienne (7):
  clk: bcm2835: remove pllb
  clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
  firmware: raspberrypi: register clk device
  cpufreq: add driver for Raspbery Pi
  clk: raspberrypi: register platform device for raspberrypi-cpufreq
  ARM: defconfig: enable cpufreq driver for RPi
  arm64: defconfig: enable cpufreq support for RPi3

 arch/arm/configs/bcm2835_defconfig    |   9 +
 arch/arm/configs/multi_v7_defconfig   |   2 +
 arch/arm64/configs/defconfig          |   2 +
 drivers/clk/bcm/Kconfig               |   7 +
 drivers/clk/bcm/Makefile              |   1 +
 drivers/clk/bcm/clk-bcm2835.c         |  28 +--
 drivers/clk/bcm/clk-raspberrypi.c     | 315 ++++++++++++++++++++++++++
 drivers/cpufreq/Kconfig.arm           |   8 +
 drivers/cpufreq/Makefile              |   1 +
 drivers/cpufreq/raspberrypi-cpufreq.c |  97 ++++++++
 drivers/firmware/raspberrypi.c        |  10 +
 11 files changed, 456 insertions(+), 24 deletions(-)
 create mode 100644 drivers/clk/bcm/clk-raspberrypi.c
 create mode 100644 drivers/cpufreq/raspberrypi-cpufreq.c

-- 
2.21.0

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ