| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAOCk7NrKa9YvoTmbhXDeKp6cKWOaXmD67LJNf=obgtx7GnZfVg@mail.gmail.com>
Date: Thu, 13 Jun 2019 09:41:12 -0600
From: Jeffrey Hugo <jeffrey.l.hugo@...il.com>
To: Bjorn Andersson <bjorn.andersson@...aro.org>
Cc: lgirdwood@...il.com, broonie@...nel.org,
Andy Gross <agross@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
MSM <linux-arm-msm@...r.kernel.org>,
lkml <linux-kernel@...r.kernel.org>, devicetree@...r.kernel.org,
Jorge Ramirez <jorge.ramirez-ortiz@...aro.org>
Subject: Re: [PATCH v3 7/7] drivers: regulator: qcom: add PMS405 SPMI regulator
On Thu, Jun 13, 2019 at 9:33 AM Bjorn Andersson
<bjorn.andersson@...aro.org> wrote:
>
> On Thu 13 Jun 07:24 PDT 2019, Jeffrey Hugo wrote:
>
> > From: Jorge Ramirez <jorge.ramirez-ortiz@...aro.org>
> >
> > The PMS405 has 5 HFSMPS and 13 LDO regulators,
> >
> > This commit adds support for one of the 5 HFSMPS regulators (s3) to
> > the spmi regulator driver.
> >
> > The PMIC HFSMPS 430 regulators have 8 mV step size and a voltage
> > control scheme consisting of two 8-bit registers defining a 16-bit
> > voltage set point in units of millivolts
> >
> > S3 controls the cpu voltages (s3 is a buck regulator of type HFS430);
> > it is therefore required so we can enable voltage scaling for safely
> > running cpufreq.
> >
> > Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@...aro.org>
> > Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@...il.com>
> > ---
> > drivers/regulator/qcom_spmi-regulator.c | 41 +++++++++++++++++++++++--
> > 1 file changed, 38 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
> > index c7880c1d4bcd..975655e787fe 100644
> > --- a/drivers/regulator/qcom_spmi-regulator.c
> > +++ b/drivers/regulator/qcom_spmi-regulator.c
> > @@ -105,6 +105,7 @@ enum spmi_regulator_logical_type {
> > SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS,
> > SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO,
> > SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426,
> > + SPMI_REGULATOR_LOGICAL_TYPE_HFS430,
> > };
> >
> > enum spmi_regulator_type {
> > @@ -157,6 +158,7 @@ enum spmi_regulator_subtype {
> > SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2 = 0x0e,
> > SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL3 = 0x0f,
> > SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL4 = 0x10,
> > + SPMI_REGULATOR_SUBTYPE_HFS430 = 0x0a,
> > };
> >
> > enum spmi_common_regulator_registers {
> > @@ -302,6 +304,8 @@ enum spmi_common_control_register_index {
> > /* Clock rate in kHz of the FTSMPS426 regulator reference clock. */
> > #define SPMI_FTSMPS426_CLOCK_RATE 4800
> >
> > +#define SPMI_HFS430_CLOCK_RATE 1600
> > +
> > /* Minimum voltage stepper delay for each step. */
> > #define SPMI_FTSMPS426_STEP_DELAY 2
> >
> > @@ -515,6 +519,10 @@ static struct spmi_voltage_range ult_pldo_ranges[] = {
> > SPMI_VOLTAGE_RANGE(0, 1750000, 1750000, 3337500, 3337500, 12500),
> > };
> >
> > +static struct spmi_voltage_range hfs430_ranges[] = {
> > + SPMI_VOLTAGE_RANGE(0, 320000, 320000, 2040000, 2040000, 8000),
> > +};
> > +
> > static DEFINE_SPMI_SET_POINTS(pldo);
> > static DEFINE_SPMI_SET_POINTS(nldo1);
> > static DEFINE_SPMI_SET_POINTS(nldo2);
> > @@ -530,6 +538,7 @@ static DEFINE_SPMI_SET_POINTS(ult_lo_smps);
> > static DEFINE_SPMI_SET_POINTS(ult_ho_smps);
> > static DEFINE_SPMI_SET_POINTS(ult_nldo);
> > static DEFINE_SPMI_SET_POINTS(ult_pldo);
> > +static DEFINE_SPMI_SET_POINTS(hfs430);
> >
> > static inline int spmi_vreg_read(struct spmi_regulator *vreg, u16 addr, u8 *buf,
> > int len)
> > @@ -1397,12 +1406,24 @@ static struct regulator_ops spmi_ftsmps426_ops = {
> > .set_pull_down = spmi_regulator_common_set_pull_down,
> > };
> >
> > +static struct regulator_ops spmi_hfs430_ops = {
> > + /* always on regulators */
> > + .set_voltage_sel = spmi_regulator_ftsmps426_set_voltage,
> > + .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel,
> > + .get_voltage = spmi_regulator_ftsmps426_get_voltage,
> > + .map_voltage = spmi_regulator_single_map_voltage,
> > + .list_voltage = spmi_regulator_common_list_voltage,
> > + .set_mode = spmi_regulator_ftsmps426_set_mode,
> > + .get_mode = spmi_regulator_ftsmps426_get_mode,
> > +};
> > +
> > /* Maximum possible digital major revision value */
> > #define INF 0xFF
> >
> > static const struct spmi_regulator_mapping supported_regulators[] = {
> > /* type subtype dig_min dig_max ltype ops setpoints hpm_min */
> > SPMI_VREG(BUCK, GP_CTL, 0, INF, SMPS, smps, smps, 100000),
> > + SPMI_VREG(BUCK, HFS430, 0, INF, HFS430, hfs430, hfs430, 10000),
> > SPMI_VREG(LDO, N300, 0, INF, LDO, ldo, nldo1, 10000),
> > SPMI_VREG(LDO, N600, 0, 0, LDO, ldo, nldo2, 10000),
> > SPMI_VREG(LDO, N1200, 0, 0, LDO, ldo, nldo2, 10000),
> > @@ -1570,7 +1591,8 @@ static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg)
> > return ret;
> > }
> >
> > -static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
> > +static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg,
> > + int clock_rate)
> > {
> > int ret;
> > u8 reg = 0;
> > @@ -1587,7 +1609,7 @@ static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
> > delay >>= SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT;
> >
> > /* slew_rate has units of uV/us */
> > - slew_rate = SPMI_FTSMPS426_CLOCK_RATE * range->step_uV;
> > + slew_rate = clock_rate * range->step_uV;
> > slew_rate /= 1000 * (SPMI_FTSMPS426_STEP_DELAY << delay);
> > slew_rate *= SPMI_FTSMPS426_STEP_MARGIN_NUM;
> > slew_rate /= SPMI_FTSMPS426_STEP_MARGIN_DEN;
> > @@ -1739,7 +1761,14 @@ static int spmi_regulator_of_parse(struct device_node *node,
> > return ret;
> > break;
> > case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426:
> > - ret = spmi_regulator_init_slew_rate_ftsmps426(vreg);
> > + ret = spmi_regulator_init_slew_rate_ftsmps426(vreg,
> > + SPMI_FTSMPS426_CLOCK_RATE);
> > + if (ret)
> > + return ret;
> > + break;
> > + case SPMI_REGULATOR_LOGICAL_TYPE_HFS430:
> > + ret = spmi_regulator_init_slew_rate_ftsmps426(vreg,
> > + SPMI_HFS430_CLOCK_RATE);
> > if (ret)
> > return ret;
> > break;
> > @@ -1907,6 +1936,11 @@ static const struct spmi_regulator_data pm8005_regulators[] = {
> > { }
> > };
> >
> > +static const struct spmi_regulator_data pms405_regulators[] = {
> > + { "s3", 0x1a00, }, /* supply name in the dts only */
>
> Not sure what this comment is trying to say. The third element here
> should be the string that is used to find the supply as specified in DT.
> For s3 this is "vdd_s3".
>
>
> So please drop the comment and make this:
> { "s3", 0x1a00, "s3" },
Makes sense, will update.
>
> Regards,
> Bjorn
>
> > + { }
> > +};
> > +
> > static const struct of_device_id qcom_spmi_regulator_match[] = {
> > { .compatible = "qcom,pm8005-regulators", .data = &pm8005_regulators },
> > { .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators },
> > @@ -1914,6 +1948,7 @@ static const struct of_device_id qcom_spmi_regulator_match[] = {
> > { .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators },
> > { .compatible = "qcom,pm8994-regulators", .data = &pm8994_regulators },
> > { .compatible = "qcom,pmi8994-regulators", .data = &pmi8994_regulators },
> > + { .compatible = "qcom,pms405-regulators", .data = &pms405_regulators },
> > { }
> > };
> > MODULE_DEVICE_TABLE(of, qcom_spmi_regulator_match);
> > --
> > 2.17.1
> >
Powered by blists - more mailing lists