linux-kernel - [v3 0/2] mtd: nand: Add Cadence NAND controller driver

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-ID: <20190614150638.28383-1-piotrs@cadence.com>
Date:   Fri, 14 Jun 2019 16:06:38 +0100
From:   Piotr Sroka <piotrs@...ence.com>
To:     <linux-kernel@...r.kernel.org>
CC:     Boris Brezillon <bbrezillon@...nel.org>,
        Miquel Raynal <miquel.raynal@...tlin.com>,
        Richard Weinberger <richard@....at>,
        "David Woodhouse" <dwmw2@...radead.org>,
        Brian Norris <computersforpeace@...il.com>,
        Marek Vasut <marek.vasut@...il.com>,
        Paul Burton <paul.burton@...s.com>,
        Geert Uytterhoeven <geert@...ux-m68k.org>,
        Arnd Bergmann <arnd@...db.de>,
        Marcel Ziswiler <marcel.ziswiler@...adex.com>,
        Dmitry Osipenko <digetx@...il.com>,
        Stefan Agner <stefan@...er.ch>,
        <linux-mtd@...ts.infradead.org>, Piotr Sroka <piotrs@...ence.com>
Subject: [v3 0/2] mtd: nand: Add Cadence NAND controller driver

Driver for Cadence HPNFC NAND flash controller.

HW DMA interface
Page write and page read operations are executed in Command DMA mode.
Commands are defined by DMA descriptors.
In CDMA mode controller own DMA engine is used (Master DMA mode).
Other operations defined by nand_op_instr are executed in "Generic" mode.
In that mode data can be transferred only in by Slave DMA interface.
Slave DMA interface can be connected directly to AXI or to an external
DMA engine.

HW ECC support
Cadence NAND controller supports HW BCH correction.
 ECC is transparent from SW point of view. It means that ECC codes
are calculated and written to flash. In read operation ECC codes 
are removed from user data and correction is made if necessary.

Controller data layout with ECC enabled:
 -------------------------------------------------------------------------
|Sec 1 | ECC | Sec 2 | ECC ...... | Sec n | OOB (32B) | ECC | unused data |
 -------------------------------------------------------------------------

Last sector is extended by a out-bound data. Tha maximum size of
"extra data" is 32 bytes. The oob data are protected by ECC. If we need to 
read only oob data the whole last sector must be read. It is because 
oob data are part of last sector. Reading oob function always reads 
whole sector and writing oob function always writes whole last sector.
Written data are interleaved with the ECC therefore part of the 
last sector is located on oob area and the BBM is overwritten.

SKIP BYTES feature
To protect BBM the "skip byte" HW feature is used. 
Write page function copies BBM value from first byte of oob data to 
BBM offset defined by manufacturer. Read page functions always takes 
BBM from flash manufacturer offset. It causes that for not written 
pages the proper value of BBM marker is used.

ECC size calculation
Information about supported ECC steps and ECC strengths are read 
from controller registers. ECC sector size and ECC strength can be
configurable. Size of ECC depends on maximum supported sector size 
it not depends on selected sector size. Therefore there is a separate
function for calculating ECC size for each of possible 
sector size/step size.

Piotr Sroka (2):
  Add new Cadence NAND driver to MTD subsystem
  dt-bindings: nand: Add Cadence NAND controller driver

 .../bindings/mtd/cadence-nand-controller.txt       |   51 +
 drivers/mtd/nand/raw/Kconfig                       |    7 +
 drivers/mtd/nand/raw/Makefile                      |    1 +
 drivers/mtd/nand/raw/cadence-nand-controller.c     | 3119 ++++++++++++++++++++
 4 files changed, 3178 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt
 create mode 100644 drivers/mtd/nand/raw/cadence-nand-controller.c

-- 
2.15.0