linux-kernel - [PATCH v2 2/3] mmc: sdhci: sdhci-pci-o2micro: Check if controller supports 8-bit width

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:   Mon, 17 Jun 2019 14:10:13 -0600
From:   Raul E Rangel <rrangel@...omium.org>
To:     linux-mmc@...r.kernel.org
Cc:     ernest.zhang@...hubtech.com, djkurtz@...omium.org,
        Raul E Rangel <rrangel@...omium.org>,
        linux-kernel@...r.kernel.org,
        Adrian Hunter <adrian.hunter@...el.com>,
        Ulf Hansson <ulf.hansson@...aro.org>
Subject: [PATCH v2 2/3] mmc: sdhci: sdhci-pci-o2micro: Check if controller supports 8-bit width

The O2 controller supports 8-bit EMMC access.

JESD84-B51 section A.6.3.a defines the bus testing procedure that
`mmc_select_bus_width()` implements. This is used to determine the actual
bus width of the eMMC.

Signed-off-by: Raul E Rangel <rrangel@...omium.org>
---
I tested this on an AMD chromebook.

$ cat /sys/kernel/debug/mmc1/ios
clock:          200000000 Hz
actual clock:   200000000 Hz
vdd:            21 (3.3 ~ 3.4 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      3 (8 bits)
timing spec:    9 (mmc HS200)
signal voltage: 1 (1.80 V)
driver type:    0 (driver type B)

Before this patch only 4 bit was negotiated.

 drivers/mmc/host/sdhci-pci-o2micro.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index dd21315922c87..9dc4548271b4b 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -395,11 +395,21 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 {
 	struct sdhci_pci_chip *chip;
 	struct sdhci_host *host;
-	u32 reg;
+	u32 reg, caps;
 	int ret;
 
 	chip = slot->chip;
 	host = slot->host;
+
+	caps = sdhci_readl(host, SDHCI_CAPABILITIES);
+
+	/*
+	 * mmc_select_bus_width() will test the bus to determine the actual bus
+	 * width.
+	 */
+	if (caps & SDHCI_CAN_DO_8BIT)
+		host->mmc->caps |= MMC_CAP_8_BIT_DATA;
+
 	switch (chip->pdev->device) {
 	case PCI_DEVICE_ID_O2_SDS0:
 	case PCI_DEVICE_ID_O2_SEABIRD0:
-- 
2.22.0.410.gd8fdbe21b5-goog