linux-kernel - Re: [PATCHv6 2/2] mtd: spi-nor: cadence-quadspi: add reset control

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <ea6000bd-51ec-d9bd-7d48-e5bebcc621dd@ti.com>
Date:   Thu, 27 Jun 2019 18:58:15 +0530
From:   Vignesh Raghavendra <vigneshr@...com>
To:     Dinh Nguyen <dinguyen@...nel.org>, <linux-mtd@...ts.infradead.org>
CC:     <marex@...x.de>, Tien-Fong Chee <tien.fong.chee@...el.com>,
        <bbrezillon@...nel.org>, <tudor.ambarus@...rochip.com>,
        <linux-kernel@...r.kernel.org>, <computersforpeace@...il.com>,
        <dwmw2@...radead.org>
Subject: Re: [PATCHv6 2/2] mtd: spi-nor: cadence-quadspi: add reset control



On 13/06/19 5:01 PM, Dinh Nguyen wrote:
> Get the reset control properties for the QSPI controller and bring them
> out of reset. Most will have just one reset bit, but there is an additional
> OCP reset bit that is used ECC. The OCP reset bit will also need to get
> de-asserted as well. [1]
> 
> The reason this patch is needed is in the case where a bootloader leaves
> the QSPI controller in a reset state, or a state where init cannot occur
> successfully, the patch will put the QSPI controller into a clean state.
> 
> [1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html
> 
> Suggested-by: Tien-Fong Chee <tien.fong.chee@...el.com>
> Signed-off-by: Dinh Nguyen <dinguyen@...nel.org>
> ---


Reviewed-by: Vignesh Raghavendra <vigneshr@...com>

Regards
Vignesh

> v6: no need to check for reset pointer in assert/deassert as the call to
>     assert/deassert is already doing the checking
> v5: remove udelay(not needed) on tested hardware
>     group reset assert/deassert together
>     update commit message with reasoning for patch
> v4: fix compile error
> v3: return full error by using PTR_ERR(rtsc)
>     move reset control calls until after the clock enables
>     use udelay(2) to be safe
>     Add optional OCP(Open Core Protocol) reset signal
> v2: use devm_reset_control_get_optional_exclusive
>     print an error message
>     return -EPROBE_DEFER
> ---
>  drivers/mtd/spi-nor/cadence-quadspi.c | 22 ++++++++++++++++++++++
>  1 file changed, 22 insertions(+)
> 
> diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c
> index 792628750eec..732323c2adb1 100644
> --- a/drivers/mtd/spi-nor/cadence-quadspi.c
> +++ b/drivers/mtd/spi-nor/cadence-quadspi.c
> @@ -34,6 +34,7 @@
>  #include <linux/of.h>
>  #include <linux/platform_device.h>
>  #include <linux/pm_runtime.h>
> +#include <linux/reset.h>
>  #include <linux/sched.h>
>  #include <linux/spi/spi.h>
>  #include <linux/timer.h>
> @@ -1336,6 +1337,8 @@ static int cqspi_probe(struct platform_device *pdev)
>  	struct cqspi_st *cqspi;
>  	struct resource *res;
>  	struct resource *res_ahb;
> +	struct reset_control *rstc;
> +	struct reset_control *rstc_ocp;
>  	const struct cqspi_driver_platdata *ddata;
>  	int ret;
>  	int irq;
> @@ -1402,6 +1405,25 @@ static int cqspi_probe(struct platform_device *pdev)
>  		goto probe_clk_failed;
>  	}
>  
> +	/* Obtain QSPI reset control */
> +	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
> +	if (IS_ERR(rstc)) {
> +		dev_err(dev, "Cannot get QSPI reset.\n");
> +		return PTR_ERR(rstc);
> +	}
> +
> +	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
> +	if (IS_ERR(rstc_ocp)) {
> +		dev_err(dev, "Cannot get QSPI OCP reset.\n");
> +		return PTR_ERR(rstc_ocp);
> +	}
> +
> +	reset_control_assert(rstc);
> +	reset_control_deassert(rstc);
> +
> +	reset_control_assert(rstc_ocp);
> +	reset_control_deassert(rstc_ocp);
> +
>  	cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk);
>  	ddata  = of_device_get_match_data(dev);
>  	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
> 

-- 
Regards
Vignesh