[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20190628141326.swgl3kg4fj5pmlqx@valkosipuli.retiisi.org.uk>
Date: Fri, 28 Jun 2019 17:13:26 +0300
From: Sakari Ailus <sakari.ailus@....fi>
To: Luis Oliveira <Luis.Oliveira@...opsys.com>
Cc: mchehab@...nel.org, davem@...emloft.net,
gregkh@...uxfoundation.org, Jonathan.Cameron@...wei.com,
robh@...nel.org, nicolas.ferre@...rochip.com,
paulmck@...ux.ibm.com, mark.rutland@....com, kishon@...com,
devicetree@...r.kernel.org, linux-media@...r.kernel.org,
linux-kernel@...r.kernel.org, Joao.Pinto@...opsys.com
Subject: Re: [v4 1/6] dt-bindings: media: Document bindings for DW MIPI CSI-2
Host
Hi Luis,
Thank you for the patchset.
On Tue, Jun 11, 2019 at 09:20:50PM +0200, Luis Oliveira wrote:
> From: Luis Oliveira <lolivei@...opsys.com>
>
> Add bindings for Synopsys DesignWare MIPI CSI-2 host.
>
> Signed-off-by: Luis Oliveira <lolivei@...opsys.com>
> ---
> Changelog
> v3-v4
> - remove "plat" from the block name @rob @laurent
> - remove "phy-names" when single-entry @rob
> - remove "snps,output-type" -> went to the driver config @laurent
>
> .../devicetree/bindings/media/snps,dw-csi.txt | 41 ++++++++++++++++++++++
> 1 file changed, 41 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi.txt
>
> diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi.txt b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> new file mode 100644
> index 0000000..613b7f9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> @@ -0,0 +1,41 @@
> +Synopsys DesignWare CSI-2 Host controller
> +
> +Description
> +-----------
> +
> +This HW block is used to receive image coming from an MIPI CSI-2 compatible
> +camera.
> +
> +Required properties:
> +- compatible : shall be "snps,dw-csi"
> +- reg : physical base address and size of the device memory
> + mapped registers;
> +- interrupts : DW CSI-2 Host interrupts
> +- phys : List of one PHY specifier (as defined in
> + Documentation/devicetree/bindings/phy/phy-bindings.txt).
> + This PHY is a MIPI DPHY working in RX mode.
> +- resets : Reference to a reset controller (optional)
> +
> +The per-board settings:
> + - port sub-node describing a single endpoint connected to the camera as
> + described in video-interfaces.txt[1].
Which endpoint properties in video-interfaces.txt are relevant for the
hardware? Which values may they have?
> +
> +Example:
> +
> + csi2: csi2@...0 {
> + compatible = "snps,dw-csi";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = < 0x03000 0x7FF>;
reg = <0x03000 0x7FF>;
> + phys = <&mipi_dphy_rx>;
> + resets = <&dw_rst 1>;
> + interrupts = <2>;
> +
> + port@0 {
> + reg = <0>;
You can drop "@0" and the reg property.
> + csi_ep1: endpoint {
> + remote-endpoint = <&camera_1>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
--
Kind regards,
Sakari Ailus
Powered by blists - more mailing lists