| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20190702125134.4m5fvdcpuqlrg6ek@pengutronix.de>
Date: Tue, 2 Jul 2019 14:51:34 +0200
From: Marco Felsch <m.felsch@...gutronix.de>
To: Igor Opaniuk <igor.opaniuk@...adex.com>
Cc: "mark.rutland@....com" <mark.rutland@....com>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
Marcel Ziswiler <marcel.ziswiler@...adex.com>,
Fabio Estevam <festevam@...il.com>,
"s.hauer@...gutronix.de" <s.hauer@...gutronix.de>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
Stefan Agner <stefan@...er.ch>,
"robh+dt@...nel.org" <robh+dt@...nel.org>,
"linux-imx@....com" <linux-imx@....com>,
"kernel@...gutronix.de" <kernel@...gutronix.de>,
Shawn Guo <shawnguo@...nel.org>,
Linux ARM <linux-arm-kernel@...ts.infradead.org>,
Marcel Ziswiler <marcel@...wiler.com>
Subject: Re: [PATCH v2 1/1] ARM: dts: colibri: introduce dts with UHS-I
support enabled
Hi Igor,
On 19-07-02 09:42, Igor Opaniuk wrote:
> Hi Marco,
>
> On Tue, Jul 2, 2019 at 10:27 AM Marco Felsch <m.felsch@...gutronix.de> wrote:
> >
> > Hi Igor,
> >
> > On 19-05-14 17:38, Igor Opaniuk wrote:
> > > Introduce DTS for Colibri iMX6S/DL V1.1x re-design, where UHS-I support was
> > > added. Provide proper configuration for VGEN3, which allows that rail to
> > > be automatically switched to 1.8 volts for proper UHS-I operation mode.
> > >
> > > Signed-off-by: Igor Opaniuk <igor.opaniuk@...adex.com>
> > > ---
> > >
> > > v2:
> > > - rework hierarchy of dts files, and a separate dtsi for Colibri
> > > iMX6S/DL V1.1x re-design, where UHS-I was added
> > > - add comments about vgen3 power rail
> > > - fix other minor issues, addressing Marcel's comments.
> > >
> > > arch/arm/boot/dts/Makefile | 1 +
> > > .../boot/dts/imx6dl-colibri-v1.1-eval-v3.dts | 220 +++++
> > > arch/arm/boot/dts/imx6qdl-colibri-v1.1.dtsi | 852 ++++++++++++++++++
> > > 3 files changed, 1073 insertions(+)
> > > create mode 100644 arch/arm/boot/dts/imx6dl-colibri-v1.1-eval-v3.dts
> > > create mode 100644 arch/arm/boot/dts/imx6qdl-colibri-v1.1.dtsi
> > >
> > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > > index dab2914fa293..dc4ea05c8e2a 100644
> > > --- a/arch/arm/boot/dts/Makefile
> > > +++ b/arch/arm/boot/dts/Makefile
> > > @@ -401,6 +401,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > > imx6dl-aristainetos2_4.dtb \
> > > imx6dl-aristainetos2_7.dtb \
> > > imx6dl-colibri-eval-v3.dtb \
> > > + imx6dl-colibri-v1.1-eval-v3.dtb \
> >
> > I don't know the style convention but xxx-v1.1-eval-v3.dtb seems weird
> > to me.
>
> This was done intentionally. The first version (v1.1) is for SoM, the
> second one (v3)
> is for a carrier board. There is an explanation below.
I mean the point between the v1.1 maybe this should be v11 or v1_1.
> >
> > > imx6dl-cubox-i.dtb \
> > > imx6dl-cubox-i-emmc-som-v15.dtb \
> > > imx6dl-cubox-i-som-v15.dtb \
> > > diff --git a/arch/arm/boot/dts/imx6dl-colibri-v1.1-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-v1.1-eval-v3.dts
> > > new file mode 100644
> > > index 000000000000..8ed7a528e7c7
> > > --- /dev/null
> > > +++ b/arch/arm/boot/dts/imx6dl-colibri-v1.1-eval-v3.dts
> > > @@ -0,0 +1,220 @@
> > > +// SPDX-License-Identifier: GPL-2.0+ OR X11
> > > +/*
> > > + * Copyright 2019 Toradex AG
> > > + */
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include <dt-bindings/input/input.h>
> > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > +#include "imx6dl.dtsi"
> > > +#include "imx6qdl-colibri-v1.1.dtsi"
> >
> > Same here..
> >
> > Why you don't use the exsiting "imx6qdl-colibri.dtsi"? The
> > "imx6qdl-colibri-v1.1.dtsi" would be a lot of boilerplate code. Instead
> > you can use the existing one and apply your changes. I don't know why
> > the vgen3 node isn't available currently but you can add them without
> > worries. Just drop the boot-default-on property within the the dtsi. Why
> > do you need this at all?
> >
> > I checked the v1.1 and the v1 DTS to and this is exactly the same code.
> > So you can avoid even more code and improve maintainability.
> >
> > I would do something like this:
>
> This was done already for v1, and there was a discussion about that [1].
> The problem is that it brakes the earlier defined hierarchy of device tree
> sources [2].
Can you provide me the link please?
> Currently we have 3 levels:
> 1. SoC level: imx6qdl.dtsi(all iMX6 SoCs) and imx6dl.dtsi (iMX6DL/S SoCs),
> that contain CPU/GPU configuration, all common peripherals configuration.
> 2. SoM level: imx6qdl-colibri.dtsi common configuration (pinmuxes, UART),
> common on module peripherals
> 3. Carrier board level: imx6dl-colibri-v1.1-eval-v3.dts specific carrier board
> configuration (where eval-v3 is the name and the version of a carrier board)
I know that kind of hierarchy ;)
> The UHS-I feature was not present on V1.0x Colibri iMX6 modules
> but got only added later as part of the V1.1x re-design. For this
> purposes I added
> imx6qdl-colibri-v1.1.dtsi for this particular re-designed version.
The vgen3 regulator node can be available in the imx6qdl-colibri.dtsi even
if it isn't used on the v1.0. The comment should highlight that.
> Another issue is that a proper pinctrl and power configuration should
> be provided for usdhc1 to support UHS-I feature, which is done in Carier
> board-level, this is why a separate DTS file (specifically for
> Colibri iMX6 v1.1 SoM) was introduced.
The last dts node will override/expand the underlying nodes. The
'no-1-8-v' should be moved to the v1.0 dts or you need to add
'/delete-property/ no-1-8-v' to your v1.1 dts. All other properties will
exapand the node.
> I understand your objection here, but unfortunately I have to follow
> this hierarchy.
Pleas check my above comments. Your patche duplicates a lot of code
which is common.
> As a trade-off some common parts can be moved to SoM-level common dtsi file,
> something like imx6qdl-colibri-common.dtsi, and then introduce two dtsi files
> for 1.0 and 1.1 versions of this SoM(imx6qdl-colibri-v1.0.dtsi and
> imx6qdl-colibri-v1.1.dtsi
> accordingly).
Please check my above comments.
Regards,
Marco
> >
> > 8<-------------------------------------------------
> > // SPDX-License-Identifier: GPL-2.0+ OR X11
> > /*
> > * Copyright 2019 Toradex AG
> > */
> >
> > #inculde "imx6dl-colibri-eval-v3.dts"
> >
> > / {
> > model = "Toradex Colibri iMX6DL/S V1.1 on Colibri Evaluation Board V3";
> > };
> >
> > &iomuxc {
> > pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> > fsl,pins = <
> > MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170b1
> > MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100b1
> > MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
> > MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
> > MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
> > MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
> > >;
> > };
> >
> > pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> > fsl,pins = <
> > MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f1
> > MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f1
> > MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
> > MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
> > MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
> > MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
> > >;
> > };
> > };
> >
> > /* Colibri MMC */
> > &usdhc1 {
> > pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
> > pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
> > pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
> > vmmc-supply = <®_module_3v3>;
> > vqmmc-supply = <&vgen3_reg>;
> > bus-width = <4>;
> > cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
> > disable-wp;
> > enable-sdio-wakeup;
> > keep-power-in-suspend;
> > sd-uhs-sdr12;
> > sd-uhs-sdr25;
> > sd-uhs-sdr50;
> > sd-uhs-sdr104;
> > status = "disabled";
> > };
> > 8<-------------------------------------------------
> >
> > The vgen3_reg update should be done on the imx6qdl-colibri.dtsi.
> >
> > I hope this will help you.
> >
> > Regards,
> > Marco
> >
> > > +
> > > +/ {
> > > + model = "Toradex Colibri iMX6DL/S V1.1 on Colibri Evaluation Board V3";
> > > + compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
> > > + "fsl,imx6dl";
> > > +
> > > + /* Will be filled by the bootloader */
> > > + memory@...00000 {
> > > + device_type = "memory";
> > > + reg = <0x10000000 0>;
> > > + };
> > > +
> > > + aliases {
> > > + i2c0 = &i2c2;
> > > + i2c1 = &i2c3;
> > > + };
> > > +
> > > + aliases {
> > > + rtc0 = &rtc_i2c;
> > > + rtc1 = &snvs_rtc;
> > > + };
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +
> > > + /* Fixed crystal dedicated to mcp251x */
> > > + clk16m: clock-16m {
> > > + compatible = "fixed-clock";
> > > + #clock-cells = <0>;
> > > + clock-frequency = <16000000>;
> > > + clock-output-names = "clk16m";
> > > + };
> > > +
> > > + gpio-keys {
> > > + compatible = "gpio-keys";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_gpio_keys>;
> > > +
> > > + wakeup {
> > > + label = "Wake-Up";
> > > + gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
> > > + linux,code = <KEY_WAKEUP>;
> > > + debounce-interval = <10>;
> > > + wakeup-source;
> > > + };
> > > + };
> > > +
> > > + lcd_display: disp0 {
> > > + compatible = "fsl,imx-parallel-display";
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + interface-pix-fmt = "bgr666";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_ipu1_lcdif>;
> > > + status = "okay";
> > > +
> > > + port@0 {
> > > + reg = <0>;
> > > +
> > > + lcd_display_in: endpoint {
> > > + remote-endpoint = <&ipu1_di0_disp0>;
> > > + };
> > > + };
> > > +
> > > + port@1 {
> > > + reg = <1>;
> > > +
> > > + lcd_display_out: endpoint {
> > > + remote-endpoint = <&lcd_panel_in>;
> > > + };
> > > + };
> > > + };
> > > +
> > > + panel: panel {
> > > + /*
> > > + * edt,et057090dhu: EDT 5.7" LCD TFT
> > > + * edt,et070080dh6: EDT 7.0" LCD TFT
> > > + */
> > > + compatible = "edt,et057090dhu";
> > > + backlight = <&backlight>;
> > > +
> > > + port {
> > > + lcd_panel_in: endpoint {
> > > + remote-endpoint = <&lcd_display_out>;
> > > + };
> > > + };
> > > + };
> > > +};
> > > +
> > > +&backlight {
> > > + brightness-levels = <0 127 191 223 239 247 251 255>;
> > > + default-brightness-level = <1>;
> > > + status = "okay";
> > > +};
> > > +
> > > +/* Colibri SSP */
> > > +&ecspi4 {
> > > + status = "okay";
> > > +
> > > + mcp251x0: mcp251x@0 {
> > > + compatible = "microchip,mcp2515";
> > > + reg = <0>;
> > > + clocks = <&clk16m>;
> > > + interrupt-parent = <&gpio3>;
> > > + interrupts = <27 0x2>;
> > > + spi-max-frequency = <10000000>;
> > > + status = "okay";
> > > + };
> > > +};
> > > +
> > > +&hdmi {
> > > + status = "okay";
> > > +};
> > > +
> > > +/*
> > > + * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
> > > + */
> > > +&i2c3 {
> > > + status = "okay";
> > > +
> > > + /* M41T0M6 real time clock on carrier board */
> > > + rtc_i2c: rtc@68 {
> > > + compatible = "st,m41t0";
> > > + reg = <0x68>;
> > > + };
> > > +};
> > > +
> > > +&ipu1_di0_disp0 {
> > > + remote-endpoint = <&lcd_display_in>;
> > > +};
> > > +
> > > +&pwm1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&pwm2 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&pwm3 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&pwm4 {
> > > + status = "okay";
> > > +};
> > > +
> > > +®_usb_host_vbus {
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart2 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart3 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbh1 {
> > > + vbus-supply = <®_usb_host_vbus>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbotg {
> > > + status = "okay";
> > > +};
> > > +
> > > +/* Colibri MMC */
> > > +&usdhc1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&weim {
> > > + status = "okay";
> > > +
> > > + /* weim memory map: 32MB on CS0, CS1, CS2 and CS3 */
> > > + ranges = <0 0 0x08000000 0x02000000
> > > + 1 0 0x0a000000 0x02000000
> > > + 2 0 0x0c000000 0x02000000
> > > + 3 0 0x0e000000 0x02000000>;
> > > +
> > > + /* SRAM on Colibri nEXT_CS0 */
> > > + sram@0,0 {
> > > + compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
> > > + reg = <0 0 0x00010000>;
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + bank-width = <2>;
> > > + fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
> > > + 0x00000000 0x04000040 0x00000000>;
> > > + };
> > > +
> > > + /* SRAM on Colibri nEXT_CS1 */
> > > + sram@1,0 {
> > > + compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
> > > + reg = <1 0 0x00010000>;
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + bank-width = <2>;
> > > + fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
> > > + 0x00000000 0x04000040 0x00000000>;
> > > + };
> > > +};
> > > diff --git a/arch/arm/boot/dts/imx6qdl-colibri-v1.1.dtsi b/arch/arm/boot/dts/imx6qdl-colibri-v1.1.dtsi
> > > new file mode 100644
> > > index 000000000000..e40819f05c81
> > > --- /dev/null
> > > +++ b/arch/arm/boot/dts/imx6qdl-colibri-v1.1.dtsi
> > > @@ -0,0 +1,852 @@
> > > +// SPDX-License-Identifier: GPL-2.0+ OR X11
> > > +/*
> > > + * Copyright 2019 Toradex AG
> > > + */
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +
> > > +/ {
> > > + model = "Toradex Colibri iMX6DL/S V1.1 Module";
> > > + compatible = "toradex,colibri_imx6dl", "fsl,imx6dl";
> > > +
> > > + backlight: backlight {
> > > + compatible = "pwm-backlight";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_gpio_bl_on>;
> > > + pwms = <&pwm3 0 5000000>;
> > > + enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
> > > + status = "disabled";
> > > + };
> > > +
> > > + reg_module_3v3: regulator-module-3v3 {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "+V3.3";
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + reg_module_3v3_audio: regulator-module-3v3-audio {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "+V3.3_AUDIO";
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + reg_usb_host_vbus: regulator-usb-host-vbus {
> > > + compatible = "regulator-fixed";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
> > > + regulator-name = "usb_host_vbus";
> > > + regulator-min-microvolt = <5000000>;
> > > + regulator-max-microvolt = <5000000>;
> > > + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
> > > + status = "disabled";
> > > + };
> > > +
> > > + sound {
> > > + compatible = "fsl,imx-audio-sgtl5000";
> > > + model = "imx6dl-colibri-sgtl5000";
> > > + ssi-controller = <&ssi1>;
> > > + audio-codec = <&codec>;
> > > + audio-routing =
> > > + "Headphone Jack", "HP_OUT",
> > > + "LINE_IN", "Line In Jack",
> > > + "MIC_IN", "Mic Jack",
> > > + "Mic Jack", "Mic Bias";
> > > + mux-int-port = <1>;
> > > + mux-ext-port = <5>;
> > > + };
> > > +
> > > + /* Optional S/PDIF in on SODIMM 88 and out on SODIMM 90, 137 or 168 */
> > > + sound_spdif: sound-spdif {
> > > + compatible = "fsl,imx-audio-spdif";
> > > + model = "imx-spdif";
> > > + spdif-controller = <&spdif>;
> > > + spdif-in;
> > > + spdif-out;
> > > + status = "disabled";
> > > + };
> > > +};
> > > +
> > > +&audmux {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_audmux &pinctrl_mic_gnd>;
> > > + status = "okay";
> > > +};
> > > +
> > > +/* Optional on SODIMM 55/63 */
> > > +&can1 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_flexcan1>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Optional on SODIMM 178/188 */
> > > +&can2 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_flexcan2>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri SSP */
> > > +&ecspi4 {
> > > + cs-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_ecspi4>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +&fec {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_enet>;
> > > + phy-mode = "rmii";
> > > + status = "okay";
> > > +};
> > > +
> > > +&hdmi {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_hdmi_ddc>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/*
> > > + * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
> > > + * touch screen controller
> > > + */
> > > +&i2c2 {
> > > + clock-frequency = <100000>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_i2c2>;
> > > + status = "okay";
> > > +
> > > + pmic: pfuze100@8 {
> > > + compatible = "fsl,pfuze100";
> > > + reg = <0x08>;
> > > +
> > > + regulators {
> > > + sw1a_reg: sw1ab {
> > > + regulator-min-microvolt = <300000>;
> > > + regulator-max-microvolt = <1875000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + regulator-ramp-delay = <6250>;
> > > + };
> > > +
> > > + sw1c_reg: sw1c {
> > > + regulator-min-microvolt = <300000>;
> > > + regulator-max-microvolt = <1875000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + regulator-ramp-delay = <6250>;
> > > + };
> > > +
> > > + sw3a_reg: sw3a {
> > > + regulator-min-microvolt = <400000>;
> > > + regulator-max-microvolt = <1975000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + swbst_reg: swbst {
> > > + regulator-min-microvolt = <5000000>;
> > > + regulator-max-microvolt = <5150000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + snvs_reg: vsnvs {
> > > + regulator-min-microvolt = <1000000>;
> > > + regulator-max-microvolt = <3000000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + vref_reg: vrefddr {
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + /* vgen1: unused */
> > > +
> > > + vgen2_reg: vgen2 {
> > > + regulator-min-microvolt = <800000>;
> > > + regulator-max-microvolt = <1550000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + /*
> > > + * +V3.3_1.8_SD1 coming off VGEN3 and supplying
> > > + * the i.MX 6 NVCC_SD1.
> > > + */
> > > + vgen3_reg: vgen3 {
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-boot-on;
> > > + };
> > > +
> > > + vgen4_reg: vgen4 {
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + vgen5_reg: vgen5 {
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + vgen6_reg: vgen6 {
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > + };
> > > + };
> > > +
> > > + codec: sgtl5000@a {
> > > + compatible = "fsl,sgtl5000";
> > > + reg = <0x0a>;
> > > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > > + VDDA-supply = <®_module_3v3_audio>;
> > > + VDDIO-supply = <®_module_3v3>;
> > > + VDDD-supply = <&vgen4_reg>;
> > > + lrclk-strength = <3>;
> > > + };
> > > +
> > > + /* STMPE811 touch screen controller */
> > > + stmpe811@41 {
> > > + compatible = "st,stmpe811";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_touch_int>;
> > > + reg = <0x41>;
> > > + interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
> > > + interrupt-parent = <&gpio6>;
> > > + interrupt-controller;
> > > + id = <0>;
> > > + blocks = <0x5>;
> > > + irq-trigger = <0x1>;
> > > + /* 3.25 MHz ADC clock speed */
> > > + st,adc-freq = <1>;
> > > + /* 12-bit ADC */
> > > + st,mod-12b = <1>;
> > > + /* internal ADC reference */
> > > + st,ref-sel = <0>;
> > > + /* ADC conversion time: 80 clocks */
> > > + st,sample-time = <4>;
> > > +
> > > + stmpe_touchscreen {
> > > + compatible = "st,stmpe-ts";
> > > + /* 8 sample average control */
> > > + st,ave-ctrl = <3>;
> > > + /* 7 length fractional part in z */
> > > + st,fraction-z = <7>;
> > > + /*
> > > + * 50 mA typical 80 mA max touchscreen drivers
> > > + * current limit value
> > > + */
> > > + st,i-drive = <1>;
> > > + /* 1 ms panel driver settling time */
> > > + st,settling = <3>;
> > > + /* 5 ms touch detect interrupt delay */
> > > + st,touch-det-delay = <5>;
> > > + };
> > > +
> > > + stmpe_adc {
> > > + compatible = "st,stmpe-adc";
> > > + /* forbid to use ADC channels 3-0 (touch) */
> > > + st,norequest-mask = <0x0F>;
> > > + };
> > > + };
> > > +};
> > > +
> > > +/*
> > > + * I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
> > > + */
> > > +&i2c3 {
> > > + clock-frequency = <100000>;
> > > + pinctrl-names = "default", "recovery";
> > > + pinctrl-0 = <&pinctrl_i2c3>;
> > > + pinctrl-1 = <&pinctrl_i2c3_recovery>;
> > > + scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> > > + sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri PWM<B> */
> > > +&pwm1 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_pwm1>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri PWM<D> */
> > > +&pwm2 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_pwm2>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri PWM<A> */
> > > +&pwm3 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_pwm3>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri PWM<C> */
> > > +&pwm4 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_pwm4>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Optional S/PDIF out on SODIMM 137 */
> > > +&spdif {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_spdif>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +&ssi1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +/* Colibri UART_A */
> > > +&uart1 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
> > > + fsl,dte-mode;
> > > + uart-has-rtscts;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri UART_B */
> > > +&uart2 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_uart2_dte>;
> > > + fsl,dte-mode;
> > > + uart-has-rtscts;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri UART_C */
> > > +&uart3 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_uart3_dte>;
> > > + fsl,dte-mode;
> > > + status = "disabled";
> > > +};
> > > +
> > > +&usbotg {
> > > + pinctrl-names = "default";
> > > + disable-over-current;
> > > + dr_mode = "peripheral";
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Colibri MMC */
> > > +&usdhc1 {
> > > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > > + pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
> > > + pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
> > > + pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
> > > + vmmc-supply = <®_module_3v3>;
> > > + vqmmc-supply = <&vgen3_reg>;
> > > + bus-width = <4>;
> > > + cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
> > > + disable-wp;
> > > + enable-sdio-wakeup;
> > > + keep-power-in-suspend;
> > > + sd-uhs-sdr12;
> > > + sd-uhs-sdr25;
> > > + sd-uhs-sdr50;
> > > + sd-uhs-sdr104;
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* eMMC */
> > > +&usdhc3 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_usdhc3>;
> > > + vqmmc-supply = <®_module_3v3>;
> > > + bus-width = <8>;
> > > + no-1-8-v;
> > > + non-removable;
> > > + status = "okay";
> > > +};
> > > +
> > > +&weim {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pinctrl_weim_sram &pinctrl_weim_cs0
> > > + &pinctrl_weim_cs1 &pinctrl_weim_cs2
> > > + &pinctrl_weim_rdnwr &pinctrl_weim_npwe>;
> > > + #address-cells = <2>;
> > > + #size-cells = <1>;
> > > + status = "disabled";
> > > +};
> > > +
> > > +&iomuxc {
> > > + pinctrl_audmux: audmuxgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
> > > + MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x130b0
> > > + MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
> > > + MX6QDL_PAD_KEY_ROW1__AUD5_RXD 0x130b0
> > > + /* SGTL5000 sys_mclk */
> > > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_cam_mclk: cammclkgrp {
> > > + fsl,pins = <
> > > + /* Parallel Camera CAM sys_mclk */
> > > + MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x00b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_ecspi4: ecspi4grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
> > > + MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
> > > + MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
> > > + /* SPI CS */
> > > + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x000b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_enet: enetgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> > > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> > > + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> > > + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> > > + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> > > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> > > + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> > > + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> > > + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
> > > + MX6QDL_PAD_GPIO_16__ENET_REF_CLK ((1<<30) | 0x1b0b0)
> > > + >;
> > > + };
> > > +
> > > + pinctrl_flexcan1: flexcan1grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
> > > + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_flexcan2: flexcan2grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
> > > + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_gpio_bl_on: gpioblon {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_gpio_keys: gpiokeys {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_hdmi_ddc: hdmiddcgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_KEY_COL3__HDMI_TX_DDC_SCL 0x4001b8b1
> > > + MX6QDL_PAD_KEY_ROW3__HDMI_TX_DDC_SDA 0x4001b8b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_i2c2: i2c2grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
> > > + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_i2c3: i2c3grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
> > > + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_i2c3_recovery: i2c3recoverygrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x4001b8b1
> > > + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b8b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_ipu1_csi0: ipu1csi0grp { /* Parallel Camera */
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_A17__IPU1_CSI1_DATA12 0xb0b1
> > > + MX6QDL_PAD_EIM_A18__IPU1_CSI1_DATA13 0xb0b1
> > > + MX6QDL_PAD_EIM_A19__IPU1_CSI1_DATA14 0xb0b1
> > > + MX6QDL_PAD_EIM_A20__IPU1_CSI1_DATA15 0xb0b1
> > > + MX6QDL_PAD_EIM_A21__IPU1_CSI1_DATA16 0xb0b1
> > > + MX6QDL_PAD_EIM_A22__IPU1_CSI1_DATA17 0xb0b1
> > > + MX6QDL_PAD_EIM_A23__IPU1_CSI1_DATA18 0xb0b1
> > > + MX6QDL_PAD_EIM_A24__IPU1_CSI1_DATA19 0xb0b1
> > > + MX6QDL_PAD_EIM_D17__IPU1_CSI1_PIXCLK 0xb0b1
> > > + MX6QDL_PAD_EIM_EB3__IPU1_CSI1_HSYNC 0xb0b1
> > > + MX6QDL_PAD_EIM_D29__IPU1_CSI1_VSYNC 0xb0b1
> > > + /* Disable PWM pins on camera interface */
> > > + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x40
> > > + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x40
> > > + >;
> > > + };
> > > +
> > > + pinctrl_ipu1_lcdif: ipu1lcdifgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xa1
> > > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xa1
> > > + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0xa1
> > > + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0xa1
> > > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xa1
> > > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xa1
> > > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xa1
> > > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xa1
> > > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xa1
> > > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xa1
> > > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xa1
> > > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xa1
> > > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xa1
> > > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xa1
> > > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xa1
> > > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xa1
> > > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xa1
> > > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xa1
> > > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xa1
> > > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xa1
> > > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xa1
> > > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xa1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_mic_gnd: gpiomicgnd {
> > > + fsl,pins = <
> > > + /* Controls Mic GND, PU or '1' pull Mic GND to GND */
> > > + MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_mmc_cd: gpiommccd {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_pwm1: pwm1grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_pwm2: pwm2grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
> > > + MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x00040
> > > + >;
> > > + };
> > > +
> > > + pinctrl_pwm3: pwm3grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
> > > + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x00040
> > > + >;
> > > + };
> > > +
> > > + pinctrl_pwm4: pwm4grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
> > > + fsl,pins = <
> > > + /* USBH_EN */
> > > + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x0f058
> > > + >;
> > > + };
> > > +
> > > + pinctrl_spdif: spdifgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_touch_int: gpiotouchintgrp {
> > > + fsl,pins = <
> > > + /* STMPE811 interrupt */
> > > + MX6QDL_PAD_RGMII_TD0__GPIO6_IO20 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_uart1_dce: uart1dcegrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> > > + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + /* DTE mode */
> > > + pinctrl_uart1_dte: uart1dtegrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_CSI0_DAT10__UART1_RX_DATA 0x1b0b1
> > > + MX6QDL_PAD_CSI0_DAT11__UART1_TX_DATA 0x1b0b1
> > > + MX6QDL_PAD_EIM_D19__UART1_RTS_B 0x1b0b1
> > > + MX6QDL_PAD_EIM_D20__UART1_CTS_B 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + /* Additional DTR, DSR, DCD */
> > > + pinctrl_uart1_ctrl: uart1ctrlgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
> > > + MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
> > > + MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_uart2_dte: uart2dtegrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA 0x1b0b1
> > > + MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA 0x1b0b1
> > > + MX6QDL_PAD_SD4_DAT6__UART2_RTS_B 0x1b0b1
> > > + MX6QDL_PAD_SD4_DAT5__UART2_CTS_B 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_uart3_dte: uart3dtegrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD4_CLK__UART3_TX_DATA 0x1b0b1
> > > + MX6QDL_PAD_SD4_CMD__UART3_RX_DATA 0x1b0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_usbc_det: usbcdetgrp {
> > > + fsl,pins = <
> > > + /* USBC_DET */
> > > + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
> > > + /* USBC_DET_EN */
> > > + MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26 0x0f058
> > > + /* USBC_DET_OVERWRITE */
> > > + MX6QDL_PAD_RGMII_RXC__GPIO6_IO30 0x0f058
> > > + >;
> > > + };
> > > +
> > > + pinctrl_usdhc1: usdhc1grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
> > > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
> > > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> > > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> > > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> > > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> > > + >;
> > > + };
> > > +
> > > + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170b1
> > > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100b1
> > > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
> > > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
> > > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
> > > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f1
> > > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f1
> > > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
> > > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
> > > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
> > > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_usdhc3: usdhc3grp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> > > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> > > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> > > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> > > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> > > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> > > + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> > > + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> > > + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> > > + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> > > + /* eMMC reset */
> > > + MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
> > > + >;
> > > + };
> > > +
> > > + pinctrl_weim_cs0: weimcs0grp {
> > > + fsl,pins = <
> > > + /* nEXT_CS0 */
> > > + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_weim_cs1: weimcs1grp {
> > > + fsl,pins = <
> > > + /* nEXT_CS1 */
> > > + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_weim_cs2: weimcs2grp {
> > > + fsl,pins = <
> > > + /* nEXT_CS2 */
> > > + MX6QDL_PAD_SD2_DAT1__EIM_CS2_B 0xb0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_weim_sram: weimsramgrp {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
> > > + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
> > > + /* Data */
> > > + MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
> > > + MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
> > > + MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
> > > + /* Address */
> > > + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
> > > + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
> > > + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
> > > + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
> > > + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
> > > + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
> > > + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
> > > + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
> > > + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
> > > + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
> > > + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
> > > + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
> > > + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
> > > + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
> > > + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
> > > + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
> > > + >;
> > > + };
> > > +
> > > + pinctrl_weim_rdnwr: weimrdnwr {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD2_CLK__GPIO1_IO10 0x0040
> > > + MX6QDL_PAD_RGMII_TD3__GPIO6_IO23 0x130b0
> > > + >;
> > > + };
> > > +
> > > + pinctrl_weim_npwe: weimnpwe {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x0040
> > > + MX6QDL_PAD_RGMII_TD2__GPIO6_IO22 0x130b0
> > > + >;
> > > + };
> > > +
> > > + /* ADDRESS[16:18] [25] used as GPIO */
> > > + pinctrl_weim_gpio_1: weimgpio-1 {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
> > > + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
> > > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x1b0b0
> > > + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + /* ADDRESS[19:24] used as GPIO */
> > > + pinctrl_weim_gpio_2: weimgpio-2 {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
> > > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0
> > > + MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x1b0b0
> > > + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + /* DATA[16:31] used as GPIO */
> > > + pinctrl_weim_gpio_3: weimgpio-3 {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
> > > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
> > > + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x1b0b0
> > > + MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0
> > > + MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b0b0
> > > + MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x1b0b0
> > > + MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x1b0b0
> > > + MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x1b0b0
> > > + MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
> > > + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
> > > + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
> > > + MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x1b0b0
> > > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
> > > + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b0
> > > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + /* DQM[0:3] used as GPIO */
> > > + pinctrl_weim_gpio_4: weimgpio-4 {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
> > > + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
> > > + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
> > > + MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + /* RDY used as GPIO */
> > > + pinctrl_weim_gpio_5: weimgpio-5 {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b0
> > > + >;
> > > + };
> > > +
> > > + /* ADDRESS[16] DATA[30] used as GPIO */
> > > + pinctrl_weim_gpio_6: weimgpio-6 {
> > > + fsl,pins = <
> > > + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
> > > + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0
> > > + >;
> > > + };
> > > +};
> > > --
> > > 2.17.1
> > >
> > >
> > >
> >
> > --
> > Pengutronix e.K. | |
> > Industrial Linux Solutions | http://www.pengutronix.de/ |
> > Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> > Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
> Thanks for looking into this!
>
> [1] https://patchwork.kernel.org/patch/10885309/
> [2] https://developer.toradex.com/device-tree-customization
>
> --
> Best regards - Freundliche Grüsse - Meilleures salutations
>
> Senior Development Engineer,
> Igor Opaniuk
>
> Toradex AG
> Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
> 00 (main line)
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@...ts.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Powered by blists - more mailing lists