| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20190711091612.98175-2-vishal.sagar@xilinx.com>
Date: Thu, 11 Jul 2019 14:46:11 +0530
From: Vishal Sagar <vishal.sagar@...inx.com>
To: Hyun Kwon <hyunk@...inx.com>, laurent.pinchart@...asonboard.com,
mchehab@...nel.org, robh+dt@...nel.org, mark.rutland@....com,
Michal Simek <michals@...inx.com>, linux-media@...r.kernel.org,
devicetree@...r.kernel.org, hans.verkuil@...co.com,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
Dinesh Kumar <dineshk@...inx.com>,
Sandip Kothari <sandipk@...inx.com>,
Luca Ceresoli <luca@...aceresoli.net>,
Jacopo Mondi <jacopo@...ndi.org>
Cc: Vishal Sagar <vishal.sagar@...inx.com>,
Hyun Kwon <hyun.kwon@...inx.com>, Rob Herring <robh@...nel.org>
Subject: [PATCH v10 1/2] media: dt-bindings: media: xilinx: Add Xilinx MIPI CSI-2 Rx Subsystem
Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem.
The Xilinx MIPI CSI-2 Rx Subsystem consists of a CSI-2 Rx controller, a
DPHY in Rx mode, an optional I2C controller and a Video Format Bridge.
Signed-off-by: Vishal Sagar <vishal.sagar@...inx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@...inx.com>
Reviewed-by: Rob Herring <robh@...nel.org>
Reviewed-by: Luca Ceresoli <luca@...aceresoli.net>
---
v10
- No changes
v9
- Fix xlnx,vfb description.
- s/Optional/Required endpoint property.
- Move data-lanes description from Ports to endpoint property section.
v8
- Added reset-gpios optional property to assert video_aresetn
v7
- Removed the control name from dt bindings
- Updated the example dt node name to csi2rx
v6
- Added "control" after V4L2_CID_XILINX_MIPICSISS_ACT_LANES as suggested by Luca
- Added reviewed by Rob Herring
v5
- Incorporated comments by Luca Cersoli
- Removed DPHY clock from description and example
- Removed bayer pattern from device tree MIPI CSI IP
doesn't deal with bayer pattern.
v4
- Added reviewed by Hyun Kwon
v3
- removed interrupt parent as suggested by Rob
- removed dphy clock
- moved vfb to optional properties
- Added required and optional port properties section
- Added endpoint property section
v2
- updated the compatible string to latest version supported
- removed DPHY related parameters
- added CSI v2.0 related property (including VCX for supporting upto 16
virtual channels).
- modified csi-pxl-format from string to unsigned int type where the value
is as per the CSI specification
- Defined port 0 and port 1 as sink and source ports.
- Removed max-lanes property as suggested by Rob and Sakari
.../bindings/media/xilinx/xlnx,csi2rxss.txt | 116 ++++++++++++++++++
1 file changed, 116 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
new file mode 100644
index 000000000000..913b28d543c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt
@@ -0,0 +1,116 @@
+Xilinx MIPI CSI2 Receiver Subsystem Device Tree Bindings
+--------------------------------------------------------
+
+The Xilinx MIPI CSI2 Receiver Subsystem is used to capture MIPI CSI2 traffic
+from compliant camera sensors and send the output as AXI4 Stream video data
+for image processing.
+
+The subsystem consists of a MIPI DPHY in slave mode which captures the
+data packets. This is passed along the MIPI CSI2 Rx IP which extracts the
+packet data. The optional Video Format Bridge (VFB) converts this data to
+AXI4 Stream video data.
+
+For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem.
+
+Required properties:
+--------------------
+- compatible: Must contain "xlnx,mipi-csi2-rx-subsystem-4.0".
+- reg: Physical base address and length of the registers set for the device.
+- interrupts: Property with a value describing the interrupt number.
+- clocks: List of phandles to AXI Lite and Video clocks.
+- clock-names: Must contain "lite_aclk" and "video_aclk" in the same order
+ as clocks listed in clocks property.
+- xlnx,csi-pxl-format: This denotes the CSI Data type selected in hw design.
+ Packets other than this data type (except for RAW8 and User defined data
+ types) will be filtered out. Possible values are as below -
+ 0x1E - YUV4228B
+ 0x1F - YUV42210B
+ 0x20 - RGB444
+ 0x21 - RGB555
+ 0x22 - RGB565
+ 0x23 - RGB666
+ 0x24 - RGB888
+ 0x28 - RAW6
+ 0x29 - RAW7
+ 0x2A - RAW8
+ 0x2B - RAW10
+ 0x2C - RAW12
+ 0x2D - RAW14
+ 0x2E - RAW16
+ 0x2F - RAW20
+
+
+Optional properties:
+--------------------
+- xlnx,vfb: Present when Video Format Bridge is enabled in IP configuration
+- xlnx,en-csi-v2-0: Present if CSI v2 is enabled in IP configuration.
+- xlnx,en-vcx: When present, there are maximum 16 virtual channels, else
+ only 4. This is present only if xlnx,en-csi-v2-0 is present.
+- xlnx,en-active-lanes: present if the number of active lanes can be
+ re-configured at runtime in the Protocol Configuration Register.
+ Otherwise all lanes, as set in IP configuration, are always active.
+- reset-gpios: Optional specifier for a GPIO that asserts video_aresetn.
+
+Ports
+-----
+The device node shall contain two 'port' child nodes as defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+The port@0 is a sink port and shall connect to CSI2 source like camera.
+
+The port@1 is a source port and can be connected to any video processing IP
+which can work with AXI4 Stream data.
+
+Required port properties:
+--------------------
+- reg: 0 - for sink port.
+ 1 - for source port.
+
+Required endpoint property:
+---------------------------
+- data-lanes: specifies MIPI CSI-2 data lanes as covered in video-interfaces.txt.
+ This is required only in the sink port 0 endpoint which connects to MIPI CSI2
+ source like sensor. The possible values are:
+ 1 - For 1 lane enabled in IP.
+ 1 2 - For 2 lanes enabled in IP.
+ 1 2 3 - For 3 lanes enabled in IP.
+ 1 2 3 4 - For 4 lanes enabled in IP.
+
+Example:
+
+ xcsi2rxss_1: csi2rx@...20000 {
+ compatible = "xlnx,mipi-csi2-rx-subsystem-4.0";
+ reg = <0x0 0xa0020000 0x0 0x10000>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 95 4>;
+ xlnx,csi-pxl-format = <0x2a>;
+ xlnx,vfb;
+ xlnx,en-active-lanes;
+ xlnx,en-csi-v2-0;
+ xlnx,en-vcx;
+ clock-names = "lite_aclk", "video_aclk";
+ clocks = <&misc_clk_0>, <&misc_clk_1>;
+ reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ /* Sink port */
+ reg = <0>;
+ csiss_in: endpoint {
+ data-lanes = <1 2 3 4>;
+ /* MIPI CSI2 Camera handle */
+ remote-endpoint = <&camera_out>;
+ };
+ };
+ port@1 {
+ /* Source port */
+ reg = <1>;
+ csiss_out: endpoint {
+ remote-endpoint = <&vproc_in>;
+ };
+ };
+ };
+ };
--
2.21.0
Powered by blists - more mailing lists