linux-kernel - Re: [PATCH AUTOSEL 4.14 086/105] PCI / ACPI: Use cached ACPI device state to get PCI device power state

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <01d729e3-9778-9e4f-84d2-16b7353eeee1@intel.com>
Date:   Tue, 16 Jul 2019 11:22:44 +0200
From:   "Rafael J. Wysocki" <rafael.j.wysocki@...el.com>
To:     Sasha Levin <sashal@...nel.org>, linux-kernel@...r.kernel.org,
        stable@...r.kernel.org
Cc:     Mika Westerberg <mika.westerberg@...ux.intel.com>,
        linux-acpi@...r.kernel.org, linux-pci@...r.kernel.org
Subject: Re: [PATCH AUTOSEL 4.14 086/105] PCI / ACPI: Use cached ACPI device
 state to get PCI device power state

On 7/15/2019 4:28 PM, Sasha Levin wrote:
> From: Mika Westerberg <mika.westerberg@...ux.intel.com>
>
> [ Upstream commit 83a16e3f6d70da99896c7a2639c0b60fff13afb8 ]
>
> The ACPI power state returned by acpi_device_get_power() may depend on
> the configuration of ACPI power resources in the system which may change
> any time after acpi_device_get_power() has returned, unless the
> reference counters of the ACPI power resources in question are set to
> prevent that from happening. Thus it is invalid to use acpi_device_get_power()
> in acpi_pci_get_power_state() the way it is done now and the value of
> the ->power.state field in the corresponding struct acpi_device objects
> (which reflects the ACPI power resources reference counting, among other
> things) should be used instead.
>
> As an example where this becomes an issue is Intel Ice Lake where the
> Thunderbolt controller (NHI), two PCIe root ports (RP0 and RP1) and xHCI
> all share the same power resources. The following picture with power
> resources marked with [] shows the topology:
>
>    Host bridge
>      |
>      +- RP0 ---\
>      +- RP1 ---|--+--> [TBT]
>      +- NHI --/   |
>      |            |
>      |            v
>      +- xHCI --> [D3C]
>
> Here TBT and D3C are the shared ACPI power resources. ACPI _PR3() method
> of the devices in question returns either TBT or D3C or both.
>
> Say we runtime suspend first the root ports RP0 and RP1, then NHI. Now
> since the TBT power resource is still on when the root ports are runtime
> suspended their dev->current_state is set to D3hot. When NHI is runtime
> suspended TBT is finally turned off but state of the root ports remain
> to be D3hot. Now when the xHCI is runtime suspended D3C gets also turned
> off. PCI core thus has power states of these devices cached in their
> dev->current_state as follows:
>
>    RP0 -> D3hot
>    RP1 -> D3hot
>    NHI -> D3cold
>    xHCI -> D3cold
>
> If the user now runs lspci for instance, the result is all 1's like in
> the below output (00:07.0 is the first root port, RP0):
>
> 00:07.0 PCI bridge: Intel Corporation Device 8a1d (rev ff) (prog-if ff)
>      !!! Unknown header type 7f
>      Kernel driver in use: pcieport
>
> In short the hardware state is not in sync with the software state
> anymore. The exact same thing happens with the PME polling thread which
> ends up bringing the root ports back into D0 after they are runtime
> suspended.
>
> For this reason, modify acpi_pci_get_power_state() so that it uses the
> ACPI device power state that was cached by the ACPI core. This makes the
> PCI device power state match the ACPI device power state regardless of
> state of the shared power resources which may still be on at this point.
>
> Link: https://lore.kernel.org/r/20190618161858.77834-2-mika.westerberg@linux.intel.com
> Signed-off-by: Mika Westerberg <mika.westerberg@...ux.intel.com>
> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@...el.com>
> Signed-off-by: Sasha Levin <sashal@...nel.org>
> ---
>   drivers/pci/pci-acpi.c | 3 ++-
>   1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
> index a3cedf8de863..688e195e85b4 100644
> --- a/drivers/pci/pci-acpi.c
> +++ b/drivers/pci/pci-acpi.c
> @@ -563,7 +563,8 @@ static pci_power_t acpi_pci_get_power_state(struct pci_dev *dev)
>   	if (!adev || !acpi_device_power_manageable(adev))
>   		return PCI_UNKNOWN;
>   
> -	if (acpi_device_get_power(adev, &state) || state == ACPI_STATE_UNKNOWN)
> +	state = adev->power.state;
> +	if (state == ACPI_STATE_UNKNOWN)
>   		return PCI_UNKNOWN;
>   
>   	return state_conv[state];

This requires additional changes to really work in all cases, please do 
not include it alone into -stable.