| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <efdea0d2c7c5ed65e79fb3604130a4488ec8057c.1563822216.git.evgenyz@gmail.com>
Date: Mon, 22 Jul 2019 21:53:03 +0200
From: Evgeny Kolesnikov <evgenyz@...il.com>
To: unlisted-recipients:; (no To-header on input)
Cc: Evgeny Kolesnikov <evgenyz@...il.com>,
Sebastian Reichel <sre@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Jason Cooper <jason@...edaemon.net>,
Andrew Lunn <andrew@...n.ch>,
Gregory Clement <gregory.clement@...tlin.com>,
Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>,
linux-pm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Subject: [PATCH 3/5] power/reset: Add a power off driver for UART-based PM MCUs
This adds the poweroff driver for power managing
micro controller units that are connected to a board
via the UART interface.
Signed-off-by: Evgeny Kolesnikov <evgenyz@...il.com>
---
drivers/power/reset/Kconfig | 7 ++
drivers/power/reset/Makefile | 1 +
drivers/power/reset/uart-poweroff.c | 155 ++++++++++++++++++++++++++++
3 files changed, 163 insertions(+)
create mode 100644 drivers/power/reset/uart-poweroff.c
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
index a564237278ff..02fdf45e3988 100644
--- a/drivers/power/reset/Kconfig
+++ b/drivers/power/reset/Kconfig
@@ -216,6 +216,13 @@ config POWER_RESET_RMOBILE
help
Reboot support for Renesas R-Mobile and SH-Mobile SoCs.
+config POWER_RESET_UART_POWEROFF
+ tristate "UART-based PM MCU power off driver"
+ depends on OF_GPIO
+ help
+ Power off support for boards with UART-based PM MCU
+ such as WD My Cloud NAS, QNAP Turbo NAS, Synology devices.
+
config POWER_RESET_ZX
tristate "ZTE SoCs reset driver"
depends on ARCH_ZX || COMPILE_TEST
diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
index 85da3198e4e0..efe8f25f463d 100644
--- a/drivers/power/reset/Makefile
+++ b/drivers/power/reset/Makefile
@@ -25,6 +25,7 @@ obj-$(CONFIG_POWER_RESET_KEYSTONE) += keystone-reset.o
obj-$(CONFIG_POWER_RESET_SYSCON) += syscon-reboot.o
obj-$(CONFIG_POWER_RESET_SYSCON_POWEROFF) += syscon-poweroff.o
obj-$(CONFIG_POWER_RESET_RMOBILE) += rmobile-reset.o
+obj-$(CONFIG_POWER_RESET_UART_POWEROFF) += uart-poweroff.o
obj-$(CONFIG_POWER_RESET_ZX) += zx-reboot.o
obj-$(CONFIG_REBOOT_MODE) += reboot-mode.o
obj-$(CONFIG_SYSCON_REBOOT_MODE) += syscon-reboot-mode.o
diff --git a/drivers/power/reset/uart-poweroff.c b/drivers/power/reset/uart-poweroff.c
new file mode 100644
index 000000000000..8122a6b306d7
--- /dev/null
+++ b/drivers/power/reset/uart-poweroff.c
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Power off for boards with UART-based PM MCUs
+ * such as WD My Cloud NAS, QNAP Turbo NAS, Synology devices.
+ *
+ * Copyright (C) 2019 Evgeny Kolesnikov <evgenyz@...il.com>
+ *
+ * Based on the code from:
+ *
+ * Copyright (C) 2016 Martin Mueller <mm@...21.net>
+ * Copyright (C) 2012 Andrew Lunn <andrew@...n.ch>
+ * Copyright (C) 2009 Martin Michlmayr <tbm@...ius.com>
+ * Copyright (C) 2008 Byron Bradley <byron.bbradley@...il.com>
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/serial_reg.h>
+#include <linux/kallsyms.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+
+#define UART_REG(b, x) (b + ((UART_##x) << 2))
+
+struct uart_poweroff {
+ const u8 *cmd;
+ int cmd_len;
+ void __iomem *base;
+ unsigned int divisor;
+ u32 byte_delay_ms;
+ u32 timeout_ms;
+};
+
+static void *pm_power_off_org;
+static struct uart_poweroff uart_poweroff;
+
+static void uart_power_off(void)
+{
+ int i;
+
+ /* Hijack UART and reset into sane state */
+ writel(0x83, UART_REG(uart_poweroff.base, LCR));
+ writel(uart_poweroff.divisor & 0xFF, UART_REG(uart_poweroff.base, DLL));
+ writel((uart_poweroff.divisor >> 8) & 0xFF, UART_REG(uart_poweroff.base, DLM));
+ writel(0x03, UART_REG(uart_poweroff.base, LCR));
+ writel(0x00, UART_REG(uart_poweroff.base, IER));
+ writel(0x00, UART_REG(uart_poweroff.base, FCR));
+ writel(0x00, UART_REG(uart_poweroff.base, MCR));
+
+ /* Send the command */
+ for (i = 0; i < uart_poweroff.cmd_len; i++) {
+ writel(uart_poweroff.cmd[i], UART_REG(uart_poweroff.base, TX));
+ mdelay(uart_poweroff.byte_delay_ms);
+ }
+
+ mdelay(uart_poweroff.timeout_ms);
+ WARN_ON(1);
+}
+
+static int uart_poweroff_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ static void __iomem *base;
+ struct clk *clk;
+ u32 baud;
+ bool override;
+ char symname[KSYM_NAME_LEN];
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Missing resource\n");
+ return -EINVAL;
+ }
+
+ base = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+ if (!base) {
+ dev_err(&pdev->dev, "Unable to map resource\n");
+ return -EINVAL;
+ }
+
+ /* We need to know tclk in order to calculate the UART divisor */
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "Clk missing\n");
+ return PTR_ERR(clk);
+ }
+
+ uart_poweroff.cmd = of_get_property(pdev->dev.of_node, "cmd",
+ &uart_poweroff.cmd_len);
+ if (uart_poweroff.cmd == NULL || uart_poweroff.cmd_len < 1) {
+ dev_err(&pdev->dev, "Cmd is missing or empty\n");
+ return -EINVAL;
+ }
+
+ of_property_read_u32(pdev->dev.of_node, "baud", &baud);
+ if (baud < 75 || baud > 460800) {
+ dev_err(&pdev->dev, "Baud rate is missing or invalid\n");
+ return -EINVAL;
+ }
+
+ uart_poweroff.base = base;
+ uart_poweroff.divisor =
+ ((clk_get_rate(clk) + (8 * baud)) / (16 * baud));
+ uart_poweroff.byte_delay_ms = 5;
+ uart_poweroff.timeout_ms = 1000;
+ of_property_read_u32(pdev->dev.of_node, "byte-delay",
+ &uart_poweroff.byte_delay_ms);
+ of_property_read_u32(pdev->dev.of_node, "timeout",
+ &uart_poweroff.timeout_ms);
+
+ override = of_property_read_bool(pdev->dev.of_node, "override");
+
+ if (pm_power_off && !override) {
+ lookup_symbol_name((ulong)pm_power_off, symname);
+ dev_err(&pdev->dev,
+ "The pm_power_off is already claimed by %s (%p) and override is false",
+ symname, pm_power_off);
+ return -EBUSY;
+ }
+ pm_power_off_org = pm_power_off;
+ pm_power_off = uart_power_off;
+
+ return 0;
+}
+
+static int uart_poweroff_remove(struct platform_device *pdev)
+{
+ if (pm_power_off == uart_power_off)
+ pm_power_off = pm_power_off_org;
+
+ return 0;
+}
+
+static const struct of_device_id of_uart_poweroff_match[] = {
+ { .compatible = "uart-poweroff", },
+ {},
+};
+
+static struct platform_driver uart_poweroff_driver = {
+ .probe = uart_poweroff_probe,
+ .remove = uart_poweroff_remove,
+ .driver = {
+ .name = "uart_poweroff",
+ .of_match_table = of_uart_poweroff_match,
+ },
+};
+module_platform_driver(uart_poweroff_driver);
+
+MODULE_AUTHOR("Evgeny Kolesnikov <evgenyz@...il.com>");
+MODULE_DESCRIPTION("UART-based PM MCU power off driver");
+MODULE_LICENSE("GPL v2");
--
2.21.0
Powered by blists - more mailing lists