[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <CAOMZO5CdWmVKXmNSLdbsmnU6_ZKwbeVArtOQzuTg_gtqTUnVag@mail.gmail.com>
Date: Wed, 7 Aug 2019 08:19:13 -0300
From: Fabio Estevam <festevam@...il.com>
To: Philippe Schenker <philippe.schenker@...adex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@...adex.com>,
Max Krummenacher <max.krummenacher@...adex.com>,
"stefan@...er.ch" <stefan@...er.ch>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
Rob Herring <robh+dt@...nel.org>,
Shawn Guo <shawnguo@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Michal Vokáč <michal.vokac@...ft.com>,
Stefan Agner <stefan.agner@...adex.com>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
NXP Linux Team <linux-imx@....com>,
Sascha Hauer <s.hauer@...gutronix.de>
Subject: Re: [PATCH v3 07/21] ARM: dts: imx7-colibri: fix 1.8V/UHS support
Hi Philippe,
On Wed, Aug 7, 2019 at 5:26 AM Philippe Schenker
<philippe.schenker@...adex.com> wrote:
>
> From: Stefan Agner <stefan.agner@...adex.com>
>
> Add pinmuxing and do not specify voltage restrictions for the usdhc
> instance available on the modules edge connector. This allows to use
> SD-cards with higher transfer modes if supported by the carrier board.
>
> Signed-off-by: Stefan Agner <stefan.agner@...adex.com>
> Signed-off-by: Philippe Schenker <philippe.schenker@...adex.com>
>
> ---
>
> Changes in v3:
> - Add new commit message from Stefan's proposal on ML
The commit message has been improved, but there is also another point
I mentioned earlier:
>
> Changes in v2: None
>
> arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
> 1 file changed, 22 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
> index 16d1a1ed1aff..67f5e0c87fdc 100644
> --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> @@ -326,7 +326,6 @@
> &usdhc1 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
> - no-1-8-v;
> cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> disable-wp;
> vqmmc-supply = <®_LDO2>;
> @@ -671,6 +670,28 @@
> >;
> };
>
> + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
This new entry has been added and it is not referenced.
> + fsl,pins = <
> + MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
> + MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
> + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
> + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
> + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
> + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
Same here.
Powered by blists - more mailing lists