| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20190809093158.7969-19-lkundrak@v3.sk>
Date: Fri, 9 Aug 2019 11:31:57 +0200
From: Lubomir Rintel <lkundrak@...sk>
To: Olof Johansson <olof@...om.net>
Cc: Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Thomas Gleixner <tglx@...utronix.de>,
Jason Cooper <jason@...edaemon.net>,
Marc Zyngier <maz@...nel.org>,
Kishon Vijay Abraham I <kishon@...com>,
Russell King <linux@...linux.org.uk>,
Michael Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...nel.org>, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-clk@...r.kernel.org, Lubomir Rintel <lkundrak@...sk>
Subject: [PATCH 18/19] phy: phy-mmp3-usb: add a new driver
This is the USB2 PHY as found on the Marvell MMP3 SoC. Based on Marvell GPL
release.
While at that, also add a MAINTAINERS entry including the other MMP PHY
driver.
Signed-off-by: Lubomir Rintel <lkundrak@...sk>
---
MAINTAINERS | 7 +
drivers/phy/marvell/Kconfig | 11 ++
drivers/phy/marvell/Makefile | 1 +
drivers/phy/marvell/phy-mmp3-usb.c | 291 +++++++++++++++++++++++++++++
4 files changed, 310 insertions(+)
create mode 100644 drivers/phy/marvell/phy-mmp3-usb.c
diff --git a/MAINTAINERS b/MAINTAINERS
index fb2ceb265a8c3..fb7e8edfc3d66 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10790,6 +10790,13 @@ F: arch/arm/boot/dts/mmp*
F: arch/arm/mach-mmp/
F: linux/soc/mmp/
+MMP USB PHY DRIVERS
+R: Lubomir Rintel <lkundrak@...sk>
+L: linux-arm-kernel@...ts.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: drivers/phy/marvell/phy-mmp3-usb.c
+F: drivers/phy/marvell/phy-pxa-usb.c
+
MMU GATHER AND TLB INVALIDATION
M: Will Deacon <will@...nel.org>
M: "Aneesh Kumar K.V" <aneesh.kumar@...ux.ibm.com>
diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
index 0e1642419c0bf..d33ef35b3e51b 100644
--- a/drivers/phy/marvell/Kconfig
+++ b/drivers/phy/marvell/Kconfig
@@ -102,3 +102,14 @@ config PHY_PXA_USB
The PHY driver will be used by Marvell udc/ehci/otg driver.
To compile this driver as a module, choose M here.
+
+config PHY_MMP3_USB
+ tristate "Marvell MMP3 USB PHY Driver"
+ depends on MACH_MMP3_DT || COMPILE_TEST
+ select GENERIC_PHY
+ help
+ Enable this to support Marvell MMP3 USB PHY driver for Marvell
+ SoC. This driver will do the PHY initialization and shutdown.
+ The PHY driver will be used by Marvell udc/ehci/otg driver.
+
+ To compile this driver as a module, choose M here.
diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
index 434eb9ca6cc3f..5a106b1549f41 100644
--- a/drivers/phy/marvell/Makefile
+++ b/drivers/phy/marvell/Makefile
@@ -2,6 +2,7 @@
obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY) += phy-armada375-usb2.o
obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o
obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o
+obj-$(CONFIG_PHY_MMP3_USB) += phy-mmp3-usb.o
obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY) += phy-mvebu-a3700-comphy.o
obj-$(CONFIG_PHY_MVEBU_A3700_UTMI) += phy-mvebu-a3700-utmi.o
obj-$(CONFIG_PHY_MVEBU_A38X_COMPHY) += phy-armada38x-comphy.o
diff --git a/drivers/phy/marvell/phy-mmp3-usb.c b/drivers/phy/marvell/phy-mmp3-usb.c
new file mode 100644
index 0000000000000..499869595a582
--- /dev/null
+++ b/drivers/phy/marvell/phy-mmp3-usb.c
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
+ * Copyright (C) 2018,2019 Lubomir Rintel <lkundrak@...sk>
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/soc/mmp/cputype.h>
+
+#define USB2_PLL_REG0 0x4
+#define USB2_PLL_REG1 0x8
+#define USB2_TX_REG0 0x10
+#define USB2_TX_REG1 0x14
+#define USB2_TX_REG2 0x18
+#define USB2_RX_REG0 0x20
+#define USB2_RX_REG1 0x24
+#define USB2_RX_REG2 0x28
+#define USB2_ANA_REG0 0x30
+#define USB2_ANA_REG1 0x34
+#define USB2_ANA_REG2 0x38
+#define USB2_DIG_REG0 0x3C
+#define USB2_DIG_REG1 0x40
+#define USB2_DIG_REG2 0x44
+#define USB2_DIG_REG3 0x48
+#define USB2_TEST_REG0 0x4C
+#define USB2_TEST_REG1 0x50
+#define USB2_TEST_REG2 0x54
+#define USB2_CHARGER_REG0 0x58
+#define USB2_OTG_REG0 0x5C
+#define USB2_PHY_MON0 0x60
+#define USB2_RESETVE_REG0 0x64
+#define USB2_ICID_REG0 0x78
+#define USB2_ICID_REG1 0x7C
+
+/* USB2_PLL_REG0 */
+
+/* This is for Ax stepping */
+#define USB2_PLL_FBDIV_SHIFT_MMP3 0
+#define USB2_PLL_FBDIV_MASK_MMP3 (0xFF << 0)
+
+#define USB2_PLL_REFDIV_SHIFT_MMP3 8
+#define USB2_PLL_REFDIV_MASK_MMP3 (0xF << 8)
+
+#define USB2_PLL_VDD12_SHIFT_MMP3 12
+#define USB2_PLL_VDD18_SHIFT_MMP3 14
+
+/* This is for B0 stepping */
+#define USB2_PLL_FBDIV_SHIFT_MMP3_B0 0
+#define USB2_PLL_REFDIV_SHIFT_MMP3_B0 9
+#define USB2_PLL_VDD18_SHIFT_MMP3_B0 14
+#define USB2_PLL_FBDIV_MASK_MMP3_B0 0x01FF
+#define USB2_PLL_REFDIV_MASK_MMP3_B0 0x3E00
+
+#define USB2_PLL_CAL12_SHIFT_MMP3 0
+#define USB2_PLL_CALI12_MASK_MMP3 (0x3 << 0)
+
+#define USB2_PLL_VCOCAL_START_SHIFT_MMP3 2
+
+#define USB2_PLL_KVCO_SHIFT_MMP3 4
+#define USB2_PLL_KVCO_MASK_MMP3 (0x7<<4)
+
+#define USB2_PLL_ICP_SHIFT_MMP3 8
+#define USB2_PLL_ICP_MASK_MMP3 (0x7<<8)
+
+#define USB2_PLL_LOCK_BYPASS_SHIFT_MMP3 12
+
+#define USB2_PLL_PU_PLL_SHIFT_MMP3 13
+#define USB2_PLL_PU_PLL_MASK (0x1 << 13)
+
+#define USB2_PLL_READY_MASK_MMP3 (0x1 << 15)
+
+/* USB2_TX_REG0 */
+#define USB2_TX_IMPCAL_VTH_SHIFT_MMP3 8
+#define USB2_TX_IMPCAL_VTH_MASK_MMP3 (0x7 << 8)
+
+#define USB2_TX_RCAL_START_SHIFT_MMP3 13
+
+/* USB2_TX_REG1 */
+#define USB2_TX_CK60_PHSEL_SHIFT_MMP3 0
+#define USB2_TX_CK60_PHSEL_MASK_MMP3 (0xf << 0)
+
+#define USB2_TX_AMP_SHIFT_MMP3 4
+#define USB2_TX_AMP_MASK_MMP3 (0x7 << 4)
+
+#define USB2_TX_VDD12_SHIFT_MMP3 8
+#define USB2_TX_VDD12_MASK_MMP3 (0x3 << 8)
+
+/* USB2_TX_REG2 */
+#define USB2_TX_DRV_SLEWRATE_SHIFT 10
+
+/* USB2_RX_REG0 */
+#define USB2_RX_SQ_THRESH_SHIFT_MMP3 4
+#define USB2_RX_SQ_THRESH_MASK_MMP3 (0xf << 4)
+
+#define USB2_RX_SQ_LENGTH_SHIFT_MMP3 10
+#define USB2_RX_SQ_LENGTH_MASK_MMP3 (0x3 << 10)
+
+/* USB2_ANA_REG1*/
+#define USB2_ANA_PU_ANA_SHIFT_MMP3 14
+
+/* USB2_OTG_REG0 */
+#define USB2_OTG_PU_OTG_SHIFT_MMP3 3
+
+struct mmp3_usb_phy {
+ struct phy *phy;
+ void __iomem *base;
+};
+
+static unsigned int u2o_get(void __iomem *base, unsigned int offset)
+{
+ return readl_relaxed(base + offset);
+}
+
+static void u2o_set(void __iomem *base, unsigned int offset,
+ unsigned int value)
+{
+ u32 reg;
+
+ reg = readl_relaxed(base + offset);
+ reg |= value;
+ writel_relaxed(reg, base + offset);
+ readl_relaxed(base + offset);
+}
+
+static void u2o_clear(void __iomem *base, unsigned int offset,
+ unsigned int value)
+{
+ u32 reg;
+
+ reg = readl_relaxed(base + offset);
+ reg &= ~value;
+ writel_relaxed(reg, base + offset);
+ readl_relaxed(base + offset);
+}
+
+static int mmp3_usb_phy_init(struct phy *phy)
+{
+ struct mmp3_usb_phy *mmp3_usb_phy = phy_get_drvdata(phy);
+ void __iomem *base = mmp3_usb_phy->base;
+
+ if (cpu_is_mmp3_a0()) {
+ u2o_clear(base, USB2_PLL_REG0, (USB2_PLL_FBDIV_MASK_MMP3
+ | USB2_PLL_REFDIV_MASK_MMP3));
+ u2o_set(base, USB2_PLL_REG0,
+ 0xd << USB2_PLL_REFDIV_SHIFT_MMP3
+ | 0xf0 << USB2_PLL_FBDIV_SHIFT_MMP3);
+ } else if (cpu_is_mmp3_b0()) {
+ u2o_clear(base, USB2_PLL_REG0, USB2_PLL_REFDIV_MASK_MMP3_B0
+ | USB2_PLL_FBDIV_MASK_MMP3_B0);
+ u2o_set(base, USB2_PLL_REG0,
+ 0xd << USB2_PLL_REFDIV_SHIFT_MMP3_B0
+ | 0xf0 << USB2_PLL_FBDIV_SHIFT_MMP3_B0);
+ } else {
+ dev_err(&phy->dev, "unsupported silicon revision\n");
+ return -ENODEV;
+ }
+
+ u2o_clear(base, USB2_PLL_REG1, USB2_PLL_PU_PLL_MASK
+ | USB2_PLL_ICP_MASK_MMP3
+ | USB2_PLL_KVCO_MASK_MMP3
+ | USB2_PLL_CALI12_MASK_MMP3);
+ u2o_set(base, USB2_PLL_REG1, 1 << USB2_PLL_PU_PLL_SHIFT_MMP3
+ | 1 << USB2_PLL_LOCK_BYPASS_SHIFT_MMP3
+ | 3 << USB2_PLL_ICP_SHIFT_MMP3
+ | 3 << USB2_PLL_KVCO_SHIFT_MMP3
+ | 3 << USB2_PLL_CAL12_SHIFT_MMP3);
+
+ u2o_clear(base, USB2_TX_REG0, USB2_TX_IMPCAL_VTH_MASK_MMP3);
+ u2o_set(base, USB2_TX_REG0, 2 << USB2_TX_IMPCAL_VTH_SHIFT_MMP3);
+
+ u2o_clear(base, USB2_TX_REG1, USB2_TX_VDD12_MASK_MMP3
+ | USB2_TX_AMP_MASK_MMP3
+ | USB2_TX_CK60_PHSEL_MASK_MMP3);
+ u2o_set(base, USB2_TX_REG1, 3 << USB2_TX_VDD12_SHIFT_MMP3
+ | 4 << USB2_TX_AMP_SHIFT_MMP3
+ | 4 << USB2_TX_CK60_PHSEL_SHIFT_MMP3);
+
+ u2o_clear(base, USB2_TX_REG2, 3 << USB2_TX_DRV_SLEWRATE_SHIFT);
+ u2o_set(base, USB2_TX_REG2, 2 << USB2_TX_DRV_SLEWRATE_SHIFT);
+
+ u2o_clear(base, USB2_RX_REG0, USB2_RX_SQ_THRESH_MASK_MMP3);
+ u2o_set(base, USB2_RX_REG0, 0xa << USB2_RX_SQ_THRESH_SHIFT_MMP3);
+
+ u2o_set(base, USB2_ANA_REG1, 0x1 << USB2_ANA_PU_ANA_SHIFT_MMP3);
+
+ u2o_set(base, USB2_OTG_REG0, 0x1 << USB2_OTG_PU_OTG_SHIFT_MMP3);
+
+ return 0;
+}
+
+static int mmp3_usb_phy_calibrate(struct phy *phy)
+{
+ struct mmp3_usb_phy *mmp3_usb_phy = phy_get_drvdata(phy);
+ void __iomem *base = mmp3_usb_phy->base;
+ int loops;
+
+ /*
+ * PLL VCO and TX Impedance Calibration Timing:
+ *
+ * _____________________________________
+ * PU __________|
+ * _____________________________
+ * VCOCAL START _________|
+ * ___
+ * REG_RCAL_START ________________| |________|_______
+ * | 200us | 400us | 40| 400us | USB PHY READY
+ */
+
+ udelay(200);
+ u2o_set(base, USB2_PLL_REG1, 1 << USB2_PLL_VCOCAL_START_SHIFT_MMP3);
+ udelay(400);
+ u2o_set(base, USB2_TX_REG0, 1 << USB2_TX_RCAL_START_SHIFT_MMP3);
+ udelay(40);
+ u2o_clear(base, USB2_TX_REG0, 1 << USB2_TX_RCAL_START_SHIFT_MMP3);
+ udelay(400);
+
+ loops = 0;
+ while ((u2o_get(base, USB2_PLL_REG1) & USB2_PLL_READY_MASK_MMP3) == 0) {
+ mdelay(1);
+ loops++;
+ if (loops > 100) {
+ dev_err(&phy->dev, "PLL_READY not set after 100mS.\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ return 0;
+}
+
+static const struct phy_ops mmp3_usb_phy_ops = {
+ .init = mmp3_usb_phy_init,
+ .calibrate = mmp3_usb_phy_calibrate,
+ .owner = THIS_MODULE,
+};
+
+static const struct of_device_id mmp3_usb_phy_of_match[] = {
+ { .compatible = "marvell,mmp3-usb-phy", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, mmp3_usb_phy_of_match);
+
+static int mmp3_usb_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *resource;
+ struct mmp3_usb_phy *mmp3_usb_phy;
+ struct phy_provider *provider;
+
+ mmp3_usb_phy = devm_kzalloc(dev, sizeof(*mmp3_usb_phy), GFP_KERNEL);
+ if (!mmp3_usb_phy)
+ return -ENOMEM;
+
+ resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mmp3_usb_phy->base = devm_ioremap_resource(dev, resource);
+ if (IS_ERR(mmp3_usb_phy->base)) {
+ dev_err(dev, "failed to remap PHY regs\n");
+ return PTR_ERR(mmp3_usb_phy->base);
+ }
+
+ mmp3_usb_phy->phy = devm_phy_create(dev, NULL, &mmp3_usb_phy_ops);
+ if (IS_ERR(mmp3_usb_phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(mmp3_usb_phy->phy);
+ }
+
+ phy_set_drvdata(mmp3_usb_phy->phy, mmp3_usb_phy);
+ provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(provider)) {
+ dev_err(dev, "failed to register PHY provider\n");
+ return PTR_ERR(provider);
+ }
+
+ return 0;
+}
+
+static struct platform_driver mmp3_usb_phy_driver = {
+ .probe = mmp3_usb_phy_probe,
+ .driver = {
+ .name = "mmp3-usb-phy",
+ .of_match_table = mmp3_usb_phy_of_match,
+ },
+};
+module_platform_driver(mmp3_usb_phy_driver);
+
+MODULE_AUTHOR("Lubomir Rintel <lkundrak@...sk>");
+MODULE_DESCRIPTION("Marvell MMP3 USB PHY Driver");
+MODULE_LICENSE("GPL v2");
--
2.21.0
Powered by blists - more mailing lists