linux-kernel - Re: [PATCH] extcon-intel-cht-wc: Don't reset USB data connection at probe

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20190809151116.GD30248@jeknote.loshitsa1.net>
Date:   Fri, 9 Aug 2019 18:11:16 +0300
From:   Yauhen Kharuzhy <jekhor@...il.com>
To:     Hans de Goede <hdegoede@...hat.com>
Cc:     linux-kernel@...r.kernel.org, Chanwoo Choi <cw00.choi@...sung.com>,
        MyungJoo Ham <myungjoo.ham@...sung.com>,
        Andy Shevchenko <andriy.shevchenko@...ux.intel.com>
Subject: Re: [PATCH] extcon-intel-cht-wc: Don't reset USB data connection at
 probe

On Fri, Aug 09, 2019 at 01:06:01PM +0200, Hans de Goede wrote:
> Hi,
> 
> On 8/9/19 12:01 AM, Yauhen Kharuzhy wrote:
> > Intel Cherry Trail Whiskey Cove extcon driver connect USB data lines to
> > PMIC at driver probing for further charger detection. This causes reset of
> > USB data sessions and removing all devices from bus. If system was
> > booted from Live CD or USB dongle, this makes system unusable.
> > 
> > Check if USB ID pin is floating and re-route data lines in this case
> > only, don't touch otherwise.
> > 
> > Signed-off-by: Yauhen Kharuzhy <jekhor@...il.com>
> > ---
> >   drivers/extcon/extcon-intel-cht-wc.c | 16 ++++++++++++++--
> >   1 file changed, 14 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/extcon/extcon-intel-cht-wc.c b/drivers/extcon/extcon-intel-cht-wc.c
> > index 9d32150e68db..3ae573e93e6e 100644
> > --- a/drivers/extcon/extcon-intel-cht-wc.c
> > +++ b/drivers/extcon/extcon-intel-cht-wc.c
> > @@ -338,6 +338,7 @@ static int cht_wc_extcon_probe(struct platform_device *pdev)
> >   	struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
> >   	struct cht_wc_extcon_data *ext;
> >   	unsigned long mask = ~(CHT_WC_PWRSRC_VBUS | CHT_WC_PWRSRC_USBID_MASK);
> > +	int pwrsrc_sts, id;
> >   	int irq, ret;
> >   	irq = platform_get_irq(pdev, 0);
> > @@ -387,8 +388,19 @@ static int cht_wc_extcon_probe(struct platform_device *pdev)
> >   		goto disable_sw_control;
> >   	}
> > -	/* Route D+ and D- to PMIC for initial charger detection */
> > -	cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
> > +	ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_STS, &pwrsrc_sts);
> > +	if (ret) {
> > +		dev_err(ext->dev, "Error reading pwrsrc status: %d\n", ret);
> > +		goto disable_sw_control;
> > +	}
> > +
> > +	id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
> > +
> > +	/* If no USB host or device connected, route D+ and D- to PMIC for
> > +	 * initial charger detection
> > +	 */
> > +	if (id == INTEL_USB_ID_FLOAT)
> > +		cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
> 
> The check here should be != INTEL_USB_ID_GND, when we are connected as
> device we are charging from the host we are connected to and the port
> we are connected to may be a CDP (charging downstream port) instead of
> a SDP (standard downstream port) allowing us to charge at 1.5A instead
> of 0.5A, also != INTEL_USB_ID_GND matches the condition used in
> cht_wc_extcon_pwrsrc_event to determine if we should continue with
> charger detection there.

Actually it should be checked as ((id != INTEL_USB_ID_GND) && (id !=
INTEL_USB_RID_A)), to not interrupt connection if ACA used and our host
is OTG A device (for example, if LiveCD boots from USB flash inserted
into an ACA USB hub).

> 
> Like your other patch I will try to give this one a  test-run tomorrow.
> 
> Regards,
> 
> Hans
> 
> 
> >   	/* Get initial state */
> >   	cht_wc_extcon_pwrsrc_event(ext);
> > 

-- 
Yauhen Kharuzhy