| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20190813072514.23299-8-hch@lst.de>
Date: Tue, 13 Aug 2019 09:24:53 +0200
From: Christoph Hellwig <hch@....de>
To: Tony Luck <tony.luck@...el.com>, Fenghua Yu <fenghua.yu@...el.com>,
Mike Travis <mike.travis@....com>,
Dimitri Sivanich <sivanich@....com>
Cc: Arnd Bergmann <arnd@...db.de>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
linux-ia64@...r.kernel.org, linux-ide@...r.kernel.org,
linux-scsi@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [PATCH 07/28] tty/serial: remove the ioc4_serial driver
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@....de>
---
arch/ia64/configs/generic_defconfig | 1 -
arch/ia64/configs/gensparse_defconfig | 1 -
drivers/tty/serial/Kconfig | 9 -
drivers/tty/serial/Makefile | 1 -
drivers/tty/serial/ioc4_serial.c | 2955 -------------------------
5 files changed, 2967 deletions(-)
delete mode 100644 drivers/tty/serial/ioc4_serial.c
diff --git a/arch/ia64/configs/generic_defconfig b/arch/ia64/configs/generic_defconfig
index 62698ea5d3f2..8dd921dce4b5 100644
--- a/arch/ia64/configs/generic_defconfig
+++ b/arch/ia64/configs/generic_defconfig
@@ -94,7 +94,6 @@ CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=6
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_SGI_IOC4=y
# CONFIG_HW_RANDOM is not set
CONFIG_EFI_RTC=y
CONFIG_RAW_DRIVER=m
diff --git a/arch/ia64/configs/gensparse_defconfig b/arch/ia64/configs/gensparse_defconfig
index b910318f2348..6e450a4fc93e 100644
--- a/arch/ia64/configs/gensparse_defconfig
+++ b/arch/ia64/configs/gensparse_defconfig
@@ -83,7 +83,6 @@ CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=6
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_SGI_IOC4=y
CONFIG_SERIAL_SGI_IOC3=y
# CONFIG_HW_RANDOM is not set
CONFIG_EFI_RTC=y
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index e9930af78acc..d33bd894b9f2 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -972,15 +972,6 @@ config SERIAL_JSM
To compile this driver as a module, choose M here: the
module will be called jsm.
-config SERIAL_SGI_IOC4
- tristate "SGI IOC4 controller serial support"
- depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC4
- select SERIAL_CORE
- help
- If you have an SGI Altix with an IOC4 based Base IO card
- and wish to use the serial ports on this card, say Y.
- Otherwise, say N.
-
config SERIAL_SGI_IOC3
tristate "SGI Altix IOC3 serial support"
depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC3
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index caa978980a6e..df8f9a8f7651 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -52,7 +52,6 @@ obj-$(CONFIG_SERIAL_SC16IS7XX_CORE) += sc16is7xx.o
obj-$(CONFIG_SERIAL_JSM) += jsm/
obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o
obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o
-obj-$(CONFIG_SERIAL_SGI_IOC4) += ioc4_serial.o
obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
diff --git a/drivers/tty/serial/ioc4_serial.c b/drivers/tty/serial/ioc4_serial.c
deleted file mode 100644
index db5b979e5a0c..000000000000
--- a/drivers/tty/serial/ioc4_serial.c
+++ /dev/null
@@ -1,2955 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2003-2006 Silicon Graphics, Inc. All Rights Reserved.
- */
-
-
-/*
- * This file contains a module version of the ioc4 serial driver. This
- * includes all the support functions needed (support functions, etc.)
- * and the serial driver itself.
- */
-#include <linux/errno.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial.h>
-#include <linux/circ_buf.h>
-#include <linux/serial_reg.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/ioc4.h>
-#include <linux/serial_core.h>
-#include <linux/slab.h>
-
-/*
- * interesting things about the ioc4
- */
-
-#define IOC4_NUM_SERIAL_PORTS 4 /* max ports per card */
-#define IOC4_NUM_CARDS 8 /* max cards per partition */
-
-#define GET_SIO_IR(_n) (_n == 0) ? (IOC4_SIO_IR_S0) : \
- (_n == 1) ? (IOC4_SIO_IR_S1) : \
- (_n == 2) ? (IOC4_SIO_IR_S2) : \
- (IOC4_SIO_IR_S3)
-
-#define GET_OTHER_IR(_n) (_n == 0) ? (IOC4_OTHER_IR_S0_MEMERR) : \
- (_n == 1) ? (IOC4_OTHER_IR_S1_MEMERR) : \
- (_n == 2) ? (IOC4_OTHER_IR_S2_MEMERR) : \
- (IOC4_OTHER_IR_S3_MEMERR)
-
-
-/*
- * All IOC4 registers are 32 bits wide.
- */
-
-/*
- * PCI Memory Space Map
- */
-#define IOC4_PCI_ERR_ADDR_L 0x000 /* Low Error Address */
-#define IOC4_PCI_ERR_ADDR_VLD (0x1 << 0)
-#define IOC4_PCI_ERR_ADDR_MST_ID_MSK (0xf << 1)
-#define IOC4_PCI_ERR_ADDR_MST_NUM_MSK (0xe << 1)
-#define IOC4_PCI_ERR_ADDR_MST_TYP_MSK (0x1 << 1)
-#define IOC4_PCI_ERR_ADDR_MUL_ERR (0x1 << 5)
-#define IOC4_PCI_ERR_ADDR_ADDR_MSK (0x3ffffff << 6)
-
-/* Interrupt types */
-#define IOC4_SIO_INTR_TYPE 0
-#define IOC4_OTHER_INTR_TYPE 1
-#define IOC4_NUM_INTR_TYPES 2
-
-/* Bitmasks for IOC4_SIO_IR, IOC4_SIO_IEC, and IOC4_SIO_IES */
-#define IOC4_SIO_IR_S0_TX_MT 0x00000001 /* Serial port 0 TX empty */
-#define IOC4_SIO_IR_S0_RX_FULL 0x00000002 /* Port 0 RX buf full */
-#define IOC4_SIO_IR_S0_RX_HIGH 0x00000004 /* Port 0 RX hiwat */
-#define IOC4_SIO_IR_S0_RX_TIMER 0x00000008 /* Port 0 RX timeout */
-#define IOC4_SIO_IR_S0_DELTA_DCD 0x00000010 /* Port 0 delta DCD */
-#define IOC4_SIO_IR_S0_DELTA_CTS 0x00000020 /* Port 0 delta CTS */
-#define IOC4_SIO_IR_S0_INT 0x00000040 /* Port 0 pass-thru intr */
-#define IOC4_SIO_IR_S0_TX_EXPLICIT 0x00000080 /* Port 0 explicit TX thru */
-#define IOC4_SIO_IR_S1_TX_MT 0x00000100 /* Serial port 1 */
-#define IOC4_SIO_IR_S1_RX_FULL 0x00000200 /* */
-#define IOC4_SIO_IR_S1_RX_HIGH 0x00000400 /* */
-#define IOC4_SIO_IR_S1_RX_TIMER 0x00000800 /* */
-#define IOC4_SIO_IR_S1_DELTA_DCD 0x00001000 /* */
-#define IOC4_SIO_IR_S1_DELTA_CTS 0x00002000 /* */
-#define IOC4_SIO_IR_S1_INT 0x00004000 /* */
-#define IOC4_SIO_IR_S1_TX_EXPLICIT 0x00008000 /* */
-#define IOC4_SIO_IR_S2_TX_MT 0x00010000 /* Serial port 2 */
-#define IOC4_SIO_IR_S2_RX_FULL 0x00020000 /* */
-#define IOC4_SIO_IR_S2_RX_HIGH 0x00040000 /* */
-#define IOC4_SIO_IR_S2_RX_TIMER 0x00080000 /* */
-#define IOC4_SIO_IR_S2_DELTA_DCD 0x00100000 /* */
-#define IOC4_SIO_IR_S2_DELTA_CTS 0x00200000 /* */
-#define IOC4_SIO_IR_S2_INT 0x00400000 /* */
-#define IOC4_SIO_IR_S2_TX_EXPLICIT 0x00800000 /* */
-#define IOC4_SIO_IR_S3_TX_MT 0x01000000 /* Serial port 3 */
-#define IOC4_SIO_IR_S3_RX_FULL 0x02000000 /* */
-#define IOC4_SIO_IR_S3_RX_HIGH 0x04000000 /* */
-#define IOC4_SIO_IR_S3_RX_TIMER 0x08000000 /* */
-#define IOC4_SIO_IR_S3_DELTA_DCD 0x10000000 /* */
-#define IOC4_SIO_IR_S3_DELTA_CTS 0x20000000 /* */
-#define IOC4_SIO_IR_S3_INT 0x40000000 /* */
-#define IOC4_SIO_IR_S3_TX_EXPLICIT 0x80000000 /* */
-
-/* Per device interrupt masks */
-#define IOC4_SIO_IR_S0 (IOC4_SIO_IR_S0_TX_MT | \
- IOC4_SIO_IR_S0_RX_FULL | \
- IOC4_SIO_IR_S0_RX_HIGH | \
- IOC4_SIO_IR_S0_RX_TIMER | \
- IOC4_SIO_IR_S0_DELTA_DCD | \
- IOC4_SIO_IR_S0_DELTA_CTS | \
- IOC4_SIO_IR_S0_INT | \
- IOC4_SIO_IR_S0_TX_EXPLICIT)
-#define IOC4_SIO_IR_S1 (IOC4_SIO_IR_S1_TX_MT | \
- IOC4_SIO_IR_S1_RX_FULL | \
- IOC4_SIO_IR_S1_RX_HIGH | \
- IOC4_SIO_IR_S1_RX_TIMER | \
- IOC4_SIO_IR_S1_DELTA_DCD | \
- IOC4_SIO_IR_S1_DELTA_CTS | \
- IOC4_SIO_IR_S1_INT | \
- IOC4_SIO_IR_S1_TX_EXPLICIT)
-#define IOC4_SIO_IR_S2 (IOC4_SIO_IR_S2_TX_MT | \
- IOC4_SIO_IR_S2_RX_FULL | \
- IOC4_SIO_IR_S2_RX_HIGH | \
- IOC4_SIO_IR_S2_RX_TIMER | \
- IOC4_SIO_IR_S2_DELTA_DCD | \
- IOC4_SIO_IR_S2_DELTA_CTS | \
- IOC4_SIO_IR_S2_INT | \
- IOC4_SIO_IR_S2_TX_EXPLICIT)
-#define IOC4_SIO_IR_S3 (IOC4_SIO_IR_S3_TX_MT | \
- IOC4_SIO_IR_S3_RX_FULL | \
- IOC4_SIO_IR_S3_RX_HIGH | \
- IOC4_SIO_IR_S3_RX_TIMER | \
- IOC4_SIO_IR_S3_DELTA_DCD | \
- IOC4_SIO_IR_S3_DELTA_CTS | \
- IOC4_SIO_IR_S3_INT | \
- IOC4_SIO_IR_S3_TX_EXPLICIT)
-
-/* Bitmasks for IOC4_OTHER_IR, IOC4_OTHER_IEC, and IOC4_OTHER_IES */
-#define IOC4_OTHER_IR_ATA_INT 0x00000001 /* ATAPI intr pass-thru */
-#define IOC4_OTHER_IR_ATA_MEMERR 0x00000002 /* ATAPI DMA PCI error */
-#define IOC4_OTHER_IR_S0_MEMERR 0x00000004 /* Port 0 PCI error */
-#define IOC4_OTHER_IR_S1_MEMERR 0x00000008 /* Port 1 PCI error */
-#define IOC4_OTHER_IR_S2_MEMERR 0x00000010 /* Port 2 PCI error */
-#define IOC4_OTHER_IR_S3_MEMERR 0x00000020 /* Port 3 PCI error */
-#define IOC4_OTHER_IR_KBD_INT 0x00000040 /* Keyboard/mouse */
-#define IOC4_OTHER_IR_RESERVED 0x007fff80 /* Reserved */
-#define IOC4_OTHER_IR_RT_INT 0x00800000 /* INT_OUT section output */
-#define IOC4_OTHER_IR_GEN_INT 0xff000000 /* Generic pins */
-
-#define IOC4_OTHER_IR_SER_MEMERR (IOC4_OTHER_IR_S0_MEMERR | IOC4_OTHER_IR_S1_MEMERR | \
- IOC4_OTHER_IR_S2_MEMERR | IOC4_OTHER_IR_S3_MEMERR)
-
-/* Bitmasks for IOC4_SIO_CR */
-#define IOC4_SIO_CR_CMD_PULSE_SHIFT 0 /* byte bus strobe shift */
-#define IOC4_SIO_CR_ARB_DIAG_TX0 0x00000000
-#define IOC4_SIO_CR_ARB_DIAG_RX0 0x00000010
-#define IOC4_SIO_CR_ARB_DIAG_TX1 0x00000020
-#define IOC4_SIO_CR_ARB_DIAG_RX1 0x00000030
-#define IOC4_SIO_CR_ARB_DIAG_TX2 0x00000040
-#define IOC4_SIO_CR_ARB_DIAG_RX2 0x00000050
-#define IOC4_SIO_CR_ARB_DIAG_TX3 0x00000060
-#define IOC4_SIO_CR_ARB_DIAG_RX3 0x00000070
-#define IOC4_SIO_CR_SIO_DIAG_IDLE 0x00000080 /* 0 -> active request among
- serial ports (ro) */
-/* Defs for some of the generic I/O pins */
-#define IOC4_GPCR_UART0_MODESEL 0x10 /* Pin is output to port 0
- mode sel */
-#define IOC4_GPCR_UART1_MODESEL 0x20 /* Pin is output to port 1
- mode sel */
-#define IOC4_GPCR_UART2_MODESEL 0x40 /* Pin is output to port 2
- mode sel */
-#define IOC4_GPCR_UART3_MODESEL 0x80 /* Pin is output to port 3
- mode sel */
-
-#define IOC4_GPPR_UART0_MODESEL_PIN 4 /* GIO pin controlling
- uart 0 mode select */
-#define IOC4_GPPR_UART1_MODESEL_PIN 5 /* GIO pin controlling
- uart 1 mode select */
-#define IOC4_GPPR_UART2_MODESEL_PIN 6 /* GIO pin controlling
- uart 2 mode select */
-#define IOC4_GPPR_UART3_MODESEL_PIN 7 /* GIO pin controlling
- uart 3 mode select */
-
-/* Bitmasks for serial RX status byte */
-#define IOC4_RXSB_OVERRUN 0x01 /* Char(s) lost */
-#define IOC4_RXSB_PAR_ERR 0x02 /* Parity error */
-#define IOC4_RXSB_FRAME_ERR 0x04 /* Framing error */
-#define IOC4_RXSB_BREAK 0x08 /* Break character */
-#define IOC4_RXSB_CTS 0x10 /* State of CTS */
-#define IOC4_RXSB_DCD 0x20 /* State of DCD */
-#define IOC4_RXSB_MODEM_VALID 0x40 /* DCD, CTS, and OVERRUN are valid */
-#define IOC4_RXSB_DATA_VALID 0x80 /* Data byte, FRAME_ERR PAR_ERR
- * & BREAK valid */
-
-/* Bitmasks for serial TX control byte */
-#define IOC4_TXCB_INT_WHEN_DONE 0x20 /* Interrupt after this byte is sent */
-#define IOC4_TXCB_INVALID 0x00 /* Byte is invalid */
-#define IOC4_TXCB_VALID 0x40 /* Byte is valid */
-#define IOC4_TXCB_MCR 0x80 /* Data<7:0> to modem control reg */
-#define IOC4_TXCB_DELAY 0xc0 /* Delay data<7:0> mSec */
-
-/* Bitmasks for IOC4_SBBR_L */
-#define IOC4_SBBR_L_SIZE 0x00000001 /* 0 == 1KB rings, 1 == 4KB rings */
-
-/* Bitmasks for IOC4_SSCR_<3:0> */
-#define IOC4_SSCR_RX_THRESHOLD 0x000001ff /* Hiwater mark */
-#define IOC4_SSCR_TX_TIMER_BUSY 0x00010000 /* TX timer in progress */
-#define IOC4_SSCR_HFC_EN 0x00020000 /* Hardware flow control enabled */
-#define IOC4_SSCR_RX_RING_DCD 0x00040000 /* Post RX record on delta-DCD */
-#define IOC4_SSCR_RX_RING_CTS 0x00080000 /* Post RX record on delta-CTS */
-#define IOC4_SSCR_DIAG 0x00200000 /* Bypass clock divider for sim */
-#define IOC4_SSCR_RX_DRAIN 0x08000000 /* Drain RX buffer to memory */
-#define IOC4_SSCR_DMA_EN 0x10000000 /* Enable ring buffer DMA */
-#define IOC4_SSCR_DMA_PAUSE 0x20000000 /* Pause DMA */
-#define IOC4_SSCR_PAUSE_STATE 0x40000000 /* Sets when PAUSE takes effect */
-#define IOC4_SSCR_RESET 0x80000000 /* Reset DMA channels */
-
-/* All producer/consumer pointers are the same bitfield */
-#define IOC4_PROD_CONS_PTR_4K 0x00000ff8 /* For 4K buffers */
-#define IOC4_PROD_CONS_PTR_1K 0x000003f8 /* For 1K buffers */
-#define IOC4_PROD_CONS_PTR_OFF 3
-
-/* Bitmasks for IOC4_SRCIR_<3:0> */
-#define IOC4_SRCIR_ARM 0x80000000 /* Arm RX timer */
-
-/* Bitmasks for IOC4_SHADOW_<3:0> */
-#define IOC4_SHADOW_DR 0x00000001 /* Data ready */
-#define IOC4_SHADOW_OE 0x00000002 /* Overrun error */
-#define IOC4_SHADOW_PE 0x00000004 /* Parity error */
-#define IOC4_SHADOW_FE 0x00000008 /* Framing error */
-#define IOC4_SHADOW_BI 0x00000010 /* Break interrupt */
-#define IOC4_SHADOW_THRE 0x00000020 /* Xmit holding register empty */
-#define IOC4_SHADOW_TEMT 0x00000040 /* Xmit shift register empty */
-#define IOC4_SHADOW_RFCE 0x00000080 /* Char in RX fifo has an error */
-#define IOC4_SHADOW_DCTS 0x00010000 /* Delta clear to send */
-#define IOC4_SHADOW_DDCD 0x00080000 /* Delta data carrier detect */
-#define IOC4_SHADOW_CTS 0x00100000 /* Clear to send */
-#define IOC4_SHADOW_DCD 0x00800000 /* Data carrier detect */
-#define IOC4_SHADOW_DTR 0x01000000 /* Data terminal ready */
-#define IOC4_SHADOW_RTS 0x02000000 /* Request to send */
-#define IOC4_SHADOW_OUT1 0x04000000 /* 16550 OUT1 bit */
-#define IOC4_SHADOW_OUT2 0x08000000 /* 16550 OUT2 bit */
-#define IOC4_SHADOW_LOOP 0x10000000 /* Loopback enabled */
-
-/* Bitmasks for IOC4_SRTR_<3:0> */
-#define IOC4_SRTR_CNT 0x00000fff /* Reload value for RX timer */
-#define IOC4_SRTR_CNT_VAL 0x0fff0000 /* Current value of RX timer */
-#define IOC4_SRTR_CNT_VAL_SHIFT 16
-#define IOC4_SRTR_HZ 16000 /* SRTR clock frequency */
-
-/* Serial port register map used for DMA and PIO serial I/O */
-struct ioc4_serialregs {
- uint32_t sscr;
- uint32_t stpir;
- uint32_t stcir;
- uint32_t srpir;
- uint32_t srcir;
- uint32_t srtr;
- uint32_t shadow;
-};
-
-/* IOC4 UART register map */
-struct ioc4_uartregs {
- char i4u_lcr;
- union {
- char iir; /* read only */
- char fcr; /* write only */
- } u3;
- union {
- char ier; /* DLAB == 0 */
- char dlm; /* DLAB == 1 */
- } u2;
- union {
- char rbr; /* read only, DLAB == 0 */
- char thr; /* write only, DLAB == 0 */
- char dll; /* DLAB == 1 */
- } u1;
- char i4u_scr;
- char i4u_msr;
- char i4u_lsr;
- char i4u_mcr;
-};
-
-/* short names */
-#define i4u_dll u1.dll
-#define i4u_ier u2.ier
-#define i4u_dlm u2.dlm
-#define i4u_fcr u3.fcr
-
-/* Serial port registers used for DMA serial I/O */
-struct ioc4_serial {
- uint32_t sbbr01_l;
- uint32_t sbbr01_h;
- uint32_t sbbr23_l;
- uint32_t sbbr23_h;
-
- struct ioc4_serialregs port_0;
- struct ioc4_serialregs port_1;
- struct ioc4_serialregs port_2;
- struct ioc4_serialregs port_3;
- struct ioc4_uartregs uart_0;
- struct ioc4_uartregs uart_1;
- struct ioc4_uartregs uart_2;
- struct ioc4_uartregs uart_3;
-};
-
-/* UART clock speed */
-#define IOC4_SER_XIN_CLK_66 66666667
-#define IOC4_SER_XIN_CLK_33 33333333
-
-#define IOC4_W_IES 0
-#define IOC4_W_IEC 1
-
-typedef void ioc4_intr_func_f(void *, uint32_t);
-typedef ioc4_intr_func_f *ioc4_intr_func_t;
-
-static unsigned int Num_of_ioc4_cards;
-
-/* defining this will get you LOTS of great debug info */
-//#define DEBUG_INTERRUPTS
-#define DPRINT_CONFIG(_x...) ;
-//#define DPRINT_CONFIG(_x...) printk _x
-
-/* number of characters left in xmit buffer before we ask for more */
-#define WAKEUP_CHARS 256
-
-/* number of characters we want to transmit to the lower level at a time */
-#define IOC4_MAX_CHARS 256
-#define IOC4_FIFO_CHARS 255
-
-/* Device name we're using */
-#define DEVICE_NAME_RS232 "ttyIOC"
-#define DEVICE_NAME_RS422 "ttyAIOC"
-#define DEVICE_MAJOR 204
-#define DEVICE_MINOR_RS232 50
-#define DEVICE_MINOR_RS422 84
-
-
-/* register offsets */
-#define IOC4_SERIAL_OFFSET 0x300
-
-/* flags for next_char_state */
-#define NCS_BREAK 0x1
-#define NCS_PARITY 0x2
-#define NCS_FRAMING 0x4
-#define NCS_OVERRUN 0x8
-
-/* cause we need SOME parameters ... */
-#define MIN_BAUD_SUPPORTED 1200
-#define MAX_BAUD_SUPPORTED 115200
-
-/* protocol types supported */
-#define PROTO_RS232 3
-#define PROTO_RS422 7
-
-/* Notification types */
-#define N_DATA_READY 0x01
-#define N_OUTPUT_LOWAT 0x02
-#define N_BREAK 0x04
-#define N_PARITY_ERROR 0x08
-#define N_FRAMING_ERROR 0x10
-#define N_OVERRUN_ERROR 0x20
-#define N_DDCD 0x40
-#define N_DCTS 0x80
-
-#define N_ALL_INPUT (N_DATA_READY | N_BREAK | \
- N_PARITY_ERROR | N_FRAMING_ERROR | \
- N_OVERRUN_ERROR | N_DDCD | N_DCTS)
-
-#define N_ALL_OUTPUT N_OUTPUT_LOWAT
-
-#define N_ALL_ERRORS (N_PARITY_ERROR | N_FRAMING_ERROR | N_OVERRUN_ERROR)
-
-#define N_ALL (N_DATA_READY | N_OUTPUT_LOWAT | N_BREAK | \
- N_PARITY_ERROR | N_FRAMING_ERROR | \
- N_OVERRUN_ERROR | N_DDCD | N_DCTS)
-
-#define SER_DIVISOR(_x, clk) (((clk) + (_x) * 8) / ((_x) * 16))
-#define DIVISOR_TO_BAUD(div, clk) ((clk) / 16 / (div))
-
-/* Some masks */
-#define LCR_MASK_BITS_CHAR (UART_LCR_WLEN5 | UART_LCR_WLEN6 \
- | UART_LCR_WLEN7 | UART_LCR_WLEN8)
-#define LCR_MASK_STOP_BITS (UART_LCR_STOP)
-
-#define PENDING(_p) (readl(&(_p)->ip_mem->sio_ir.raw) & _p->ip_ienb)
-#define READ_SIO_IR(_p) readl(&(_p)->ip_mem->sio_ir.raw)
-
-/* Default to 4k buffers */
-#ifdef IOC4_1K_BUFFERS
-#define RING_BUF_SIZE 1024
-#define IOC4_BUF_SIZE_BIT 0
-#define PROD_CONS_MASK IOC4_PROD_CONS_PTR_1K
-#else
-#define RING_BUF_SIZE 4096
-#define IOC4_BUF_SIZE_BIT IOC4_SBBR_L_SIZE
-#define PROD_CONS_MASK IOC4_PROD_CONS_PTR_4K
-#endif
-
-#define TOTAL_RING_BUF_SIZE (RING_BUF_SIZE * 4)
-
-/*
- * This is the entry saved by the driver - one per card
- */
-
-#define UART_PORT_MIN 0
-#define UART_PORT_RS232 UART_PORT_MIN
-#define UART_PORT_RS422 1
-#define UART_PORT_COUNT 2 /* one for each mode */
-
-struct ioc4_control {
- int ic_irq;
- struct {
- /* uart ports are allocated here - 1 for rs232, 1 for rs422 */
- struct uart_port icp_uart_port[UART_PORT_COUNT];
- /* Handy reference material */
- struct ioc4_port *icp_port;
- } ic_port[IOC4_NUM_SERIAL_PORTS];
- struct ioc4_soft *ic_soft;
-};
-
-/*
- * per-IOC4 data structure
- */
-#define MAX_IOC4_INTR_ENTS (8 * sizeof(uint32_t))
-struct ioc4_soft {
- struct ioc4_misc_regs __iomem *is_ioc4_misc_addr;
- struct ioc4_serial __iomem *is_ioc4_serial_addr;
-
- /* Each interrupt type has an entry in the array */
- struct ioc4_intr_type {
-
- /*
- * Each in-use entry in this array contains at least
- * one nonzero bit in sd_bits; no two entries in this
- * array have overlapping sd_bits values.
- */
- struct ioc4_intr_info {
- uint32_t sd_bits;
- ioc4_intr_func_f *sd_intr;
- void *sd_info;
- } is_intr_info[MAX_IOC4_INTR_ENTS];
-
- /* Number of entries active in the above array */
- atomic_t is_num_intrs;
- } is_intr_type[IOC4_NUM_INTR_TYPES];
-
- /* is_ir_lock must be held while
- * modifying sio_ie values, so
- * we can be sure that sio_ie is
- * not changing when we read it
- * along with sio_ir.
- */
- spinlock_t is_ir_lock; /* SIO_IE[SC] mod lock */
-};
-
-/* Local port info for each IOC4 serial ports */
-struct ioc4_port {
- struct uart_port *ip_port; /* current active port ptr */
- /* Ptrs for all ports */
- struct uart_port *ip_all_ports[UART_PORT_COUNT];
- /* Back ptrs for this port */
- struct ioc4_control *ip_control;
- struct pci_dev *ip_pdev;
- struct ioc4_soft *ip_ioc4_soft;
-
- /* pci mem addresses */
- struct ioc4_misc_regs __iomem *ip_mem;
- struct ioc4_serial __iomem *ip_serial;
- struct ioc4_serialregs __iomem *ip_serial_regs;
- struct ioc4_uartregs __iomem *ip_uart_regs;
-
- /* Ring buffer page for this port */
- dma_addr_t ip_dma_ringbuf;
- /* vaddr of ring buffer */
- struct ring_buffer *ip_cpu_ringbuf;
-
- /* Rings for this port */
- struct ring *ip_inring;
- struct ring *ip_outring;
-
- /* Hook to port specific values */
- struct hooks *ip_hooks;
-
- spinlock_t ip_lock;
-
- /* Various rx/tx parameters */
- int ip_baud;
- int ip_tx_lowat;
- int ip_rx_timeout;
-
- /* Copy of notification bits */
- int ip_notify;
-
- /* Shadow copies of various registers so we don't need to PIO
- * read them constantly
- */
- uint32_t ip_ienb; /* Enabled interrupts */
- uint32_t ip_sscr;
- uint32_t ip_tx_prod;
- uint32_t ip_rx_cons;
- int ip_pci_bus_speed;
- unsigned char ip_flags;
-};
-
-/* tx low water mark. We need to notify the driver whenever tx is getting
- * close to empty so it can refill the tx buffer and keep things going.
- * Let's assume that if we interrupt 1 ms before the tx goes idle, we'll
- * have no trouble getting in more chars in time (I certainly hope so).
- */
-#define TX_LOWAT_LATENCY 1000
-#define TX_LOWAT_HZ (1000000 / TX_LOWAT_LATENCY)
-#define TX_LOWAT_CHARS(baud) (baud / 10 / TX_LOWAT_HZ)
-
-/* Flags per port */
-#define INPUT_HIGH 0x01
-#define DCD_ON 0x02
-#define LOWAT_WRITTEN 0x04
-#define READ_ABORTED 0x08
-#define PORT_ACTIVE 0x10
-#define PORT_INACTIVE 0 /* This is the value when "off" */
-
-
-/* Since each port has different register offsets and bitmasks
- * for everything, we'll store those that we need in tables so we
- * don't have to be constantly checking the port we are dealing with.
- */
-struct hooks {
- uint32_t intr_delta_dcd;
- uint32_t intr_delta_cts;
- uint32_t intr_tx_mt;
- uint32_t intr_rx_timer;
- uint32_t intr_rx_high;
- uint32_t intr_tx_explicit;
- uint32_t intr_dma_error;
- uint32_t intr_clear;
- uint32_t intr_all;
- int rs422_select_pin;
-};
-
-static struct hooks hooks_array[IOC4_NUM_SERIAL_PORTS] = {
- /* Values for port 0 */
- {
- IOC4_SIO_IR_S0_DELTA_DCD, IOC4_SIO_IR_S0_DELTA_CTS,
- IOC4_SIO_IR_S0_TX_MT, IOC4_SIO_IR_S0_RX_TIMER,
- IOC4_SIO_IR_S0_RX_HIGH, IOC4_SIO_IR_S0_TX_EXPLICIT,
- IOC4_OTHER_IR_S0_MEMERR,
- (IOC4_SIO_IR_S0_TX_MT | IOC4_SIO_IR_S0_RX_FULL |
- IOC4_SIO_IR_S0_RX_HIGH | IOC4_SIO_IR_S0_RX_TIMER |
- IOC4_SIO_IR_S0_DELTA_DCD | IOC4_SIO_IR_S0_DELTA_CTS |
- IOC4_SIO_IR_S0_INT | IOC4_SIO_IR_S0_TX_EXPLICIT),
- IOC4_SIO_IR_S0, IOC4_GPPR_UART0_MODESEL_PIN,
- },
-
- /* Values for port 1 */
- {
- IOC4_SIO_IR_S1_DELTA_DCD, IOC4_SIO_IR_S1_DELTA_CTS,
- IOC4_SIO_IR_S1_TX_MT, IOC4_SIO_IR_S1_RX_TIMER,
- IOC4_SIO_IR_S1_RX_HIGH, IOC4_SIO_IR_S1_TX_EXPLICIT,
- IOC4_OTHER_IR_S1_MEMERR,
- (IOC4_SIO_IR_S1_TX_MT | IOC4_SIO_IR_S1_RX_FULL |
- IOC4_SIO_IR_S1_RX_HIGH | IOC4_SIO_IR_S1_RX_TIMER |
- IOC4_SIO_IR_S1_DELTA_DCD | IOC4_SIO_IR_S1_DELTA_CTS |
- IOC4_SIO_IR_S1_INT | IOC4_SIO_IR_S1_TX_EXPLICIT),
- IOC4_SIO_IR_S1, IOC4_GPPR_UART1_MODESEL_PIN,
- },
-
- /* Values for port 2 */
- {
- IOC4_SIO_IR_S2_DELTA_DCD, IOC4_SIO_IR_S2_DELTA_CTS,
- IOC4_SIO_IR_S2_TX_MT, IOC4_SIO_IR_S2_RX_TIMER,
- IOC4_SIO_IR_S2_RX_HIGH, IOC4_SIO_IR_S2_TX_EXPLICIT,
- IOC4_OTHER_IR_S2_MEMERR,
- (IOC4_SIO_IR_S2_TX_MT | IOC4_SIO_IR_S2_RX_FULL |
- IOC4_SIO_IR_S2_RX_HIGH | IOC4_SIO_IR_S2_RX_TIMER |
- IOC4_SIO_IR_S2_DELTA_DCD | IOC4_SIO_IR_S2_DELTA_CTS |
- IOC4_SIO_IR_S2_INT | IOC4_SIO_IR_S2_TX_EXPLICIT),
- IOC4_SIO_IR_S2, IOC4_GPPR_UART2_MODESEL_PIN,
- },
-
- /* Values for port 3 */
- {
- IOC4_SIO_IR_S3_DELTA_DCD, IOC4_SIO_IR_S3_DELTA_CTS,
- IOC4_SIO_IR_S3_TX_MT, IOC4_SIO_IR_S3_RX_TIMER,
- IOC4_SIO_IR_S3_RX_HIGH, IOC4_SIO_IR_S3_TX_EXPLICIT,
- IOC4_OTHER_IR_S3_MEMERR,
- (IOC4_SIO_IR_S3_TX_MT | IOC4_SIO_IR_S3_RX_FULL |
- IOC4_SIO_IR_S3_RX_HIGH | IOC4_SIO_IR_S3_RX_TIMER |
- IOC4_SIO_IR_S3_DELTA_DCD | IOC4_SIO_IR_S3_DELTA_CTS |
- IOC4_SIO_IR_S3_INT | IOC4_SIO_IR_S3_TX_EXPLICIT),
- IOC4_SIO_IR_S3, IOC4_GPPR_UART3_MODESEL_PIN,
- }
-};
-
-/* A ring buffer entry */
-struct ring_entry {
- union {
- struct {
- uint32_t alldata;
- uint32_t allsc;
- } all;
- struct {
- char data[4]; /* data bytes */
- char sc[4]; /* status/control */
- } s;
- } u;
-};
-
-/* Test the valid bits in any of the 4 sc chars using "allsc" member */
-#define RING_ANY_VALID \
- ((uint32_t)(IOC4_RXSB_MODEM_VALID | IOC4_RXSB_DATA_VALID) * 0x01010101)
-
-#define ring_sc u.s.sc
-#define ring_data u.s.data
-#define ring_allsc u.all.allsc
-
-/* Number of entries per ring buffer. */
-#define ENTRIES_PER_RING (RING_BUF_SIZE / (int) sizeof(struct ring_entry))
-
-/* An individual ring */
-struct ring {
- struct ring_entry entries[ENTRIES_PER_RING];
-};
-
-/* The whole enchilada */
-struct ring_buffer {
- struct ring TX_0_OR_2;
- struct ring RX_0_OR_2;
- struct ring TX_1_OR_3;
- struct ring RX_1_OR_3;
-};
-
-/* Get a ring from a port struct */
-#define RING(_p, _wh) &(((struct ring_buffer *)((_p)->ip_cpu_ringbuf))->_wh)
-
-/* Infinite loop detection.
- */
-#define MAXITER 10000000
-
-/* Prototypes */
-static void receive_chars(struct uart_port *);
-static void handle_intr(void *arg, uint32_t sio_ir);
-
-/*
- * port_is_active - determines if this port is currently active
- * @port: ptr to soft struct for this port
- * @uart_port: uart port to test for
- */
-static inline int port_is_active(struct ioc4_port *port,
- struct uart_port *uart_port)
-{
- if (port) {
- if ((port->ip_flags & PORT_ACTIVE)
- && (port->ip_port == uart_port))
- return 1;
- }
- return 0;
-}
-
-
-/**
- * write_ireg - write the interrupt regs
- * @ioc4_soft: ptr to soft struct for this port
- * @val: value to write
- * @which: which register
- * @type: which ireg set
- */
-static inline void
-write_ireg(struct ioc4_soft *ioc4_soft, uint32_t val, int which, int type)
-{
- struct ioc4_misc_regs __iomem *mem = ioc4_soft->is_ioc4_misc_addr;
- unsigned long flags;
-
- spin_lock_irqsave(&ioc4_soft->is_ir_lock, flags);
-
- switch (type) {
- case IOC4_SIO_INTR_TYPE:
- switch (which) {
- case IOC4_W_IES:
- writel(val, &mem->sio_ies.raw);
- break;
-
- case IOC4_W_IEC:
- writel(val, &mem->sio_iec.raw);
- break;
- }
- break;
-
- case IOC4_OTHER_INTR_TYPE:
- switch (which) {
- case IOC4_W_IES:
- writel(val, &mem->other_ies.raw);
- break;
-
- case IOC4_W_IEC:
- writel(val, &mem->other_iec.raw);
- break;
- }
- break;
-
- default:
- break;
- }
- spin_unlock_irqrestore(&ioc4_soft->is_ir_lock, flags);
-}
-
-/**
- * set_baud - Baud rate setting code
- * @port: port to set
- * @baud: baud rate to use
- */
-static int set_baud(struct ioc4_port *port, int baud)
-{
- int actual_baud;
- int diff;
- int lcr;
- unsigned short divisor;
- struct ioc4_uartregs __iomem *uart;
-
- divisor = SER_DIVISOR(baud, port->ip_pci_bus_speed);
- if (!divisor)
- return 1;
- actual_baud = DIVISOR_TO_BAUD(divisor, port->ip_pci_bus_speed);
-
- diff = actual_baud - baud;
- if (diff < 0)
- diff = -diff;
-
- /* If we're within 1%, we've found a match */
- if (diff * 100 > actual_baud)
- return 1;
-
- uart = port->ip_uart_regs;
- lcr = readb(&uart->i4u_lcr);
- writeb(lcr | UART_LCR_DLAB, &uart->i4u_lcr);
- writeb((unsigned char)divisor, &uart->i4u_dll);
- writeb((unsigned char)(divisor >> 8), &uart->i4u_dlm);
- writeb(lcr, &uart->i4u_lcr);
- return 0;
-}
-
-
-/**
- * get_ioc4_port - given a uart port, return the control structure
- * @port: uart port
- * @set: set this port as current
- */
-static struct ioc4_port *get_ioc4_port(struct uart_port *the_port, int set)
-{
- struct ioc4_driver_data *idd = dev_get_drvdata(the_port->dev);
- struct ioc4_control *control = idd->idd_serial_data;
- struct ioc4_port *port;
- int port_num, port_type;
-
- if (control) {
- for ( port_num = 0; port_num < IOC4_NUM_SERIAL_PORTS;
- port_num++ ) {
- port = control->ic_port[port_num].icp_port;
- if (!port)
- continue;
- for (port_type = UART_PORT_MIN;
- port_type < UART_PORT_COUNT;
- port_type++) {
- if (the_port == port->ip_all_ports
- [port_type]) {
- /* set local copy */
- if (set) {
- port->ip_port = the_port;
- }
- return port;
- }
- }
- }
- }
- return NULL;
-}
-
-/* The IOC4 hardware provides no atomic way to determine if interrupts
- * are pending since two reads are required to do so. The handler must
- * read the SIO_IR and the SIO_IES, and take the logical and of the
- * two. When this value is zero, all interrupts have been serviced and
- * the handler may return.
- *
- * This has the unfortunate "hole" that, if some other CPU or
- * some other thread or some higher level interrupt manages to
- * modify SIO_IE between our reads of SIO_IR and SIO_IE, we may
- * think we have observed SIO_IR&SIO_IE==0 when in fact this
- * condition never really occurred.
- *
- * To solve this, we use a simple spinlock that must be held
- * whenever modifying SIO_IE; holding this lock while observing
- * both SIO_IR and SIO_IE guarantees that we do not falsely
- * conclude that no enabled interrupts are pending.
- */
-
-static inline uint32_t
-pending_intrs(struct ioc4_soft *soft, int type)
-{
- struct ioc4_misc_regs __iomem *mem = soft->is_ioc4_misc_addr;
- unsigned long flag;
- uint32_t intrs = 0;
-
- BUG_ON(!((type == IOC4_SIO_INTR_TYPE)
- || (type == IOC4_OTHER_INTR_TYPE)));
-
- spin_lock_irqsave(&soft->is_ir_lock, flag);
-
- switch (type) {
- case IOC4_SIO_INTR_TYPE:
- intrs = readl(&mem->sio_ir.raw) & readl(&mem->sio_ies.raw);
- break;
-
- case IOC4_OTHER_INTR_TYPE:
- intrs = readl(&mem->other_ir.raw) & readl(&mem->other_ies.raw);
-
- /* Don't process any ATA interrupte */
- intrs &= ~(IOC4_OTHER_IR_ATA_INT | IOC4_OTHER_IR_ATA_MEMERR);
- break;
-
- default:
- break;
- }
- spin_unlock_irqrestore(&soft->is_ir_lock, flag);
- return intrs;
-}
-
-/**
- * port_init - Initialize the sio and ioc4 hardware for a given port
- * called per port from attach...
- * @port: port to initialize
- */
-static inline int port_init(struct ioc4_port *port)
-{
- uint32_t sio_cr;
- struct hooks *hooks = port->ip_hooks;
- struct ioc4_uartregs __iomem *uart;
-
- /* Idle the IOC4 serial interface */
- writel(IOC4_SSCR_RESET, &port->ip_serial_regs->sscr);
-
- /* Wait until any pending bus activity for this port has ceased */
- do
- sio_cr = readl(&port->ip_mem->sio_cr.raw);
- while (!(sio_cr & IOC4_SIO_CR_SIO_DIAG_IDLE));
-
- /* Finish reset sequence */
- writel(0, &port->ip_serial_regs->sscr);
-
- /* Once RESET is done, reload cached tx_prod and rx_cons values
- * and set rings to empty by making prod == cons
- */
- port->ip_tx_prod = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
- writel(port->ip_tx_prod, &port->ip_serial_regs->stpir);
- port->ip_rx_cons = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
- writel(port->ip_rx_cons | IOC4_SRCIR_ARM, &port->ip_serial_regs->srcir);
-
- /* Disable interrupts for this 16550 */
- uart = port->ip_uart_regs;
- writeb(0, &uart->i4u_lcr);
- writeb(0, &uart->i4u_ier);
-
- /* Set the default baud */
- set_baud(port, port->ip_baud);
-
- /* Set line control to 8 bits no parity */
- writeb(UART_LCR_WLEN8 | 0, &uart->i4u_lcr);
- /* UART_LCR_STOP == 1 stop */
-
- /* Enable the FIFOs */
- writeb(UART_FCR_ENABLE_FIFO, &uart->i4u_fcr);
- /* then reset 16550 FIFOs */
- writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
- &uart->i4u_fcr);
-
- /* Clear modem control register */
- writeb(0, &uart->i4u_mcr);
-
- /* Clear deltas in modem status register */
- readb(&uart->i4u_msr);
-
- /* Only do this once per port pair */
- if (port->ip_hooks == &hooks_array[0]
- || port->ip_hooks == &hooks_array[2]) {
- unsigned long ring_pci_addr;
- uint32_t __iomem *sbbr_l;
- uint32_t __iomem *sbbr_h;
-
- if (port->ip_hooks == &hooks_array[0]) {
- sbbr_l = &port->ip_serial->sbbr01_l;
- sbbr_h = &port->ip_serial->sbbr01_h;
- } else {
- sbbr_l = &port->ip_serial->sbbr23_l;
- sbbr_h = &port->ip_serial->sbbr23_h;
- }
-
- ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf;
- DPRINT_CONFIG(("%s: ring_pci_addr 0x%lx\n",
- __func__, ring_pci_addr));
-
- writel((unsigned int)((uint64_t)ring_pci_addr >> 32), sbbr_h);
- writel((unsigned int)ring_pci_addr | IOC4_BUF_SIZE_BIT, sbbr_l);
- }
-
- /* Set the receive timeout value to 10 msec */
- writel(IOC4_SRTR_HZ / 100, &port->ip_serial_regs->srtr);
-
- /* Set rx threshold, enable DMA */
- /* Set high water mark at 3/4 of full ring */
- port->ip_sscr = (ENTRIES_PER_RING * 3 / 4);
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
-
- /* Disable and clear all serial related interrupt bits */
- write_ireg(port->ip_ioc4_soft, hooks->intr_clear,
- IOC4_W_IEC, IOC4_SIO_INTR_TYPE);
- port->ip_ienb &= ~hooks->intr_clear;
- writel(hooks->intr_clear, &port->ip_mem->sio_ir.raw);
- return 0;
-}
-
-/**
- * handle_dma_error_intr - service any pending DMA error interrupts for the
- * given port - 2nd level called via sd_intr
- * @arg: handler arg
- * @other_ir: ioc4regs
- */
-static void handle_dma_error_intr(void *arg, uint32_t other_ir)
-{
- struct ioc4_port *port = (struct ioc4_port *)arg;
- struct hooks *hooks = port->ip_hooks;
- unsigned long flags;
-
- spin_lock_irqsave(&port->ip_lock, flags);
-
- /* ACK the interrupt */
- writel(hooks->intr_dma_error, &port->ip_mem->other_ir.raw);
-
- if (readl(&port->ip_mem->pci_err_addr_l.raw) & IOC4_PCI_ERR_ADDR_VLD) {
- printk(KERN_ERR
- "PCI error address is 0x%llx, "
- "master is serial port %c %s\n",
- (((uint64_t)readl(&port->ip_mem->pci_err_addr_h)
- << 32)
- | readl(&port->ip_mem->pci_err_addr_l.raw))
- & IOC4_PCI_ERR_ADDR_ADDR_MSK, '1' +
- ((char)(readl(&port->ip_mem->pci_err_addr_l.raw) &
- IOC4_PCI_ERR_ADDR_MST_NUM_MSK) >> 1),
- (readl(&port->ip_mem->pci_err_addr_l.raw)
- & IOC4_PCI_ERR_ADDR_MST_TYP_MSK)
- ? "RX" : "TX");
-
- if (readl(&port->ip_mem->pci_err_addr_l.raw)
- & IOC4_PCI_ERR_ADDR_MUL_ERR) {
- printk(KERN_ERR
- "Multiple errors occurred\n");
- }
- }
- spin_unlock_irqrestore(&port->ip_lock, flags);
-
- /* Re-enable DMA error interrupts */
- write_ireg(port->ip_ioc4_soft, hooks->intr_dma_error, IOC4_W_IES,
- IOC4_OTHER_INTR_TYPE);
-}
-
-/**
- * intr_connect - interrupt connect function
- * @soft: soft struct for this card
- * @type: interrupt type
- * @intrbits: bit pattern to set
- * @intr: handler function
- * @info: handler arg
- */
-static void
-intr_connect(struct ioc4_soft *soft, int type,
- uint32_t intrbits, ioc4_intr_func_f * intr, void *info)
-{
- int i;
- struct ioc4_intr_info *intr_ptr;
-
- BUG_ON(!((type == IOC4_SIO_INTR_TYPE)
- || (type == IOC4_OTHER_INTR_TYPE)));
-
- i = atomic_inc_return(&soft-> is_intr_type[type].is_num_intrs) - 1;
- BUG_ON(!(i < MAX_IOC4_INTR_ENTS || (printk("i %d\n", i), 0)));
-
- /* Save off the lower level interrupt handler */
- intr_ptr = &soft->is_intr_type[type].is_intr_info[i];
- intr_ptr->sd_bits = intrbits;
- intr_ptr->sd_intr = intr;
- intr_ptr->sd_info = info;
-}
-
-/**
- * ioc4_intr - Top level IOC4 interrupt handler.
- * @irq: irq value
- * @arg: handler arg
- */
-
-static irqreturn_t ioc4_intr(int irq, void *arg)
-{
- struct ioc4_soft *soft;
- uint32_t this_ir, this_mir;
- int xx, num_intrs = 0;
- int intr_type;
- int handled = 0;
- struct ioc4_intr_info *intr_info;
-
- soft = arg;
- for (intr_type = 0; intr_type < IOC4_NUM_INTR_TYPES; intr_type++) {
- num_intrs = (int)atomic_read(
- &soft->is_intr_type[intr_type].is_num_intrs);
-
- this_mir = this_ir = pending_intrs(soft, intr_type);
-
- /* Farm out the interrupt to the various drivers depending on
- * which interrupt bits are set.
- */
- for (xx = 0; xx < num_intrs; xx++) {
- intr_info = &soft->is_intr_type[intr_type].is_intr_info[xx];
- this_mir = this_ir & intr_info->sd_bits;
- if (this_mir) {
- /* Disable owned interrupts, call handler */
- handled++;
- write_ireg(soft, intr_info->sd_bits, IOC4_W_IEC,
- intr_type);
- intr_info->sd_intr(intr_info->sd_info, this_mir);
- this_ir &= ~this_mir;
- }
- }
- }
-#ifdef DEBUG_INTERRUPTS
- {
- struct ioc4_misc_regs __iomem *mem = soft->is_ioc4_misc_addr;
- unsigned long flag;
-
- spin_lock_irqsave(&soft->is_ir_lock, flag);
- printk ("%s : %d : mem 0x%p sio_ir 0x%x sio_ies 0x%x "
- "other_ir 0x%x other_ies 0x%x mask 0x%x\n",
- __func__, __LINE__,
- (void *)mem, readl(&mem->sio_ir.raw),
- readl(&mem->sio_ies.raw),
- readl(&mem->other_ir.raw),
- readl(&mem->other_ies.raw),
- IOC4_OTHER_IR_ATA_INT | IOC4_OTHER_IR_ATA_MEMERR);
- spin_unlock_irqrestore(&soft->is_ir_lock, flag);
- }
-#endif
- return handled ? IRQ_HANDLED : IRQ_NONE;
-}
-
-/**
- * ioc4_attach_local - Device initialization.
- * Called at *_attach() time for each
- * IOC4 with serial ports in the system.
- * @idd: Master module data for this IOC4
- */
-static inline int ioc4_attach_local(struct ioc4_driver_data *idd)
-{
- struct ioc4_port *port;
- struct ioc4_port *ports[IOC4_NUM_SERIAL_PORTS];
- int port_number;
- uint16_t ioc4_revid_min = 62;
- uint16_t ioc4_revid;
- struct pci_dev *pdev = idd->idd_pdev;
- struct ioc4_control* control = idd->idd_serial_data;
- struct ioc4_soft *soft = control->ic_soft;
- void __iomem *ioc4_misc = idd->idd_misc_regs;
- void __iomem *ioc4_serial = soft->is_ioc4_serial_addr;
-
- /* IOC4 firmware must be at least rev 62 */
- pci_read_config_word(pdev, PCI_COMMAND_SPECIAL, &ioc4_revid);
-
- printk(KERN_INFO "IOC4 firmware revision %d\n", ioc4_revid);
- if (ioc4_revid < ioc4_revid_min) {
- printk(KERN_WARNING
- "IOC4 serial not supported on firmware rev %d, "
- "please upgrade to rev %d or higher\n",
- ioc4_revid, ioc4_revid_min);
- return -EPERM;
- }
- BUG_ON(ioc4_misc == NULL);
- BUG_ON(ioc4_serial == NULL);
-
- /* Create port structures for each port */
- for (port_number = 0; port_number < IOC4_NUM_SERIAL_PORTS;
- port_number++) {
- port = kzalloc(sizeof(struct ioc4_port), GFP_KERNEL);
- if (!port) {
- printk(KERN_WARNING
- "IOC4 serial memory not available for port\n");
- goto free;
- }
- spin_lock_init(&port->ip_lock);
-
- /* we need to remember the previous ones, to point back to
- * them farther down - setting up the ring buffers.
- */
- ports[port_number] = port;
-
- /* Allocate buffers and jumpstart the hardware. */
- control->ic_port[port_number].icp_port = port;
- port->ip_ioc4_soft = soft;
- port->ip_pdev = pdev;
- port->ip_ienb = 0;
- /* Use baud rate calculations based on detected PCI
- * bus speed. Simply test whether the PCI clock is
- * running closer to 66MHz or 33MHz.
- */
- if (idd->count_period/IOC4_EXTINT_COUNT_DIVISOR < 20) {
- port->ip_pci_bus_speed = IOC4_SER_XIN_CLK_66;
- } else {
- port->ip_pci_bus_speed = IOC4_SER_XIN_CLK_33;
- }
- port->ip_baud = 9600;
- port->ip_control = control;
- port->ip_mem = ioc4_misc;
- port->ip_serial = ioc4_serial;
-
- /* point to the right hook */
- port->ip_hooks = &hooks_array[port_number];
-
- /* Get direct hooks to the serial regs and uart regs
- * for this port
- */
- switch (port_number) {
- case 0:
- port->ip_serial_regs = &(port->ip_serial->port_0);
- port->ip_uart_regs = &(port->ip_serial->uart_0);
- break;
- case 1:
- port->ip_serial_regs = &(port->ip_serial->port_1);
- port->ip_uart_regs = &(port->ip_serial->uart_1);
- break;
- case 2:
- port->ip_serial_regs = &(port->ip_serial->port_2);
- port->ip_uart_regs = &(port->ip_serial->uart_2);
- break;
- default:
- case 3:
- port->ip_serial_regs = &(port->ip_serial->port_3);
- port->ip_uart_regs = &(port->ip_serial->uart_3);
- break;
- }
-
- /* ring buffers are 1 to a pair of ports */
- if (port_number && (port_number & 1)) {
- /* odd use the evens buffer */
- port->ip_dma_ringbuf =
- ports[port_number - 1]->ip_dma_ringbuf;
- port->ip_cpu_ringbuf =
- ports[port_number - 1]->ip_cpu_ringbuf;
- port->ip_inring = RING(port, RX_1_OR_3);
- port->ip_outring = RING(port, TX_1_OR_3);
-
- } else {
- if (port->ip_dma_ringbuf == 0) {
- port->ip_cpu_ringbuf = pci_alloc_consistent
- (pdev, TOTAL_RING_BUF_SIZE,
- &port->ip_dma_ringbuf);
-
- }
- BUG_ON(!((((int64_t)port->ip_dma_ringbuf) &
- (TOTAL_RING_BUF_SIZE - 1)) == 0));
- DPRINT_CONFIG(("%s : ip_cpu_ringbuf 0x%p "
- "ip_dma_ringbuf 0x%p\n",
- __func__,
- (void *)port->ip_cpu_ringbuf,
- (void *)port->ip_dma_ringbuf));
- port->ip_inring = RING(port, RX_0_OR_2);
- port->ip_outring = RING(port, TX_0_OR_2);
- }
- DPRINT_CONFIG(("%s : port %d [addr 0x%p] control 0x%p",
- __func__,
- port_number, (void *)port, (void *)control));
- DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n",
- (void *)port->ip_serial_regs,
- (void *)port->ip_uart_regs));
-
- /* Initialize the hardware for IOC4 */
- port_init(port);
-
- DPRINT_CONFIG(("%s: port_number %d port 0x%p inring 0x%p "
- "outring 0x%p\n",
- __func__,
- port_number, (void *)port,
- (void *)port->ip_inring,
- (void *)port->ip_outring));
-
- /* Attach interrupt handlers */
- intr_connect(soft, IOC4_SIO_INTR_TYPE,
- GET_SIO_IR(port_number),
- handle_intr, port);
-
- intr_connect(soft, IOC4_OTHER_INTR_TYPE,
- GET_OTHER_IR(port_number),
- handle_dma_error_intr, port);
- }
- return 0;
-
-free:
- while (port_number)
- kfree(ports[--port_number]);
- return -ENOMEM;
-}
-
-/**
- * enable_intrs - enable interrupts
- * @port: port to enable
- * @mask: mask to use
- */
-static void enable_intrs(struct ioc4_port *port, uint32_t mask)
-{
- struct hooks *hooks = port->ip_hooks;
-
- if ((port->ip_ienb & mask) != mask) {
- write_ireg(port->ip_ioc4_soft, mask, IOC4_W_IES,
- IOC4_SIO_INTR_TYPE);
- port->ip_ienb |= mask;
- }
-
- if (port->ip_ienb)
- write_ireg(port->ip_ioc4_soft, hooks->intr_dma_error,
- IOC4_W_IES, IOC4_OTHER_INTR_TYPE);
-}
-
-/**
- * local_open - local open a port
- * @port: port to open
- */
-static inline int local_open(struct ioc4_port *port)
-{
- int spiniter = 0;
-
- port->ip_flags = PORT_ACTIVE;
-
- /* Pause the DMA interface if necessary */
- if (port->ip_sscr & IOC4_SSCR_DMA_EN) {
- writel(port->ip_sscr | IOC4_SSCR_DMA_PAUSE,
- &port->ip_serial_regs->sscr);
- while((readl(&port->ip_serial_regs-> sscr)
- & IOC4_SSCR_PAUSE_STATE) == 0) {
- spiniter++;
- if (spiniter > MAXITER) {
- port->ip_flags = PORT_INACTIVE;
- return -1;
- }
- }
- }
-
- /* Reset the input fifo. If the uart received chars while the port
- * was closed and DMA is not enabled, the uart may have a bunch of
- * chars hanging around in its rx fifo which will not be discarded
- * by rclr in the upper layer. We must get rid of them here.
- */
- writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR,
- &port->ip_uart_regs->i4u_fcr);
-
- writeb(UART_LCR_WLEN8, &port->ip_uart_regs->i4u_lcr);
- /* UART_LCR_STOP == 1 stop */
-
- /* Re-enable DMA, set default threshold to intr whenever there is
- * data available.
- */
- port->ip_sscr &= ~IOC4_SSCR_RX_THRESHOLD;
- port->ip_sscr |= 1; /* default threshold */
-
- /* Plug in the new sscr. This implicitly clears the DMA_PAUSE
- * flag if it was set above
- */
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- port->ip_tx_lowat = 1;
- return 0;
-}
-
-/**
- * set_rx_timeout - Set rx timeout and threshold values.
- * @port: port to use
- * @timeout: timeout value in ticks
- */
-static inline int set_rx_timeout(struct ioc4_port *port, int timeout)
-{
- int threshold;
-
- port->ip_rx_timeout = timeout;
-
- /* Timeout is in ticks. Let's figure out how many chars we
- * can receive at the current baud rate in that interval
- * and set the rx threshold to that amount. There are 4 chars
- * per ring entry, so we'll divide the number of chars that will
- * arrive in timeout by 4.
- * So .... timeout * baud / 10 / HZ / 4, with HZ = 100.
- */
- threshold = timeout * port->ip_baud / 4000;
- if (threshold == 0)
- threshold = 1; /* otherwise we'll intr all the time! */
-
- if ((unsigned)threshold > (unsigned)IOC4_SSCR_RX_THRESHOLD)
- return 1;
-
- port->ip_sscr &= ~IOC4_SSCR_RX_THRESHOLD;
- port->ip_sscr |= threshold;
-
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
-
- /* Now set the rx timeout to the given value
- * again timeout * IOC4_SRTR_HZ / HZ
- */
- timeout = timeout * IOC4_SRTR_HZ / 100;
- if (timeout > IOC4_SRTR_CNT)
- timeout = IOC4_SRTR_CNT;
-
- writel(timeout, &port->ip_serial_regs->srtr);
- return 0;
-}
-
-/**
- * config_port - config the hardware
- * @port: port to config
- * @baud: baud rate for the port
- * @byte_size: data size
- * @stop_bits: number of stop bits
- * @parenb: parity enable ?
- * @parodd: odd parity ?
- */
-static inline int
-config_port(struct ioc4_port *port,
- int baud, int byte_size, int stop_bits, int parenb, int parodd)
-{
- char lcr, sizebits;
- int spiniter = 0;
-
- DPRINT_CONFIG(("%s: baud %d byte_size %d stop %d parenb %d parodd %d\n",
- __func__, baud, byte_size, stop_bits, parenb, parodd));
-
- if (set_baud(port, baud))
- return 1;
-
- switch (byte_size) {
- case 5:
- sizebits = UART_LCR_WLEN5;
- break;
- case 6:
- sizebits = UART_LCR_WLEN6;
- break;
- case 7:
- sizebits = UART_LCR_WLEN7;
- break;
- case 8:
- sizebits = UART_LCR_WLEN8;
- break;
- default:
- return 1;
- }
-
- /* Pause the DMA interface if necessary */
- if (port->ip_sscr & IOC4_SSCR_DMA_EN) {
- writel(port->ip_sscr | IOC4_SSCR_DMA_PAUSE,
- &port->ip_serial_regs->sscr);
- while((readl(&port->ip_serial_regs->sscr)
- & IOC4_SSCR_PAUSE_STATE) == 0) {
- spiniter++;
- if (spiniter > MAXITER)
- return -1;
- }
- }
-
- /* Clear relevant fields in lcr */
- lcr = readb(&port->ip_uart_regs->i4u_lcr);
- lcr &= ~(LCR_MASK_BITS_CHAR | UART_LCR_EPAR |
- UART_LCR_PARITY | LCR_MASK_STOP_BITS);
-
- /* Set byte size in lcr */
- lcr |= sizebits;
-
- /* Set parity */
- if (parenb) {
- lcr |= UART_LCR_PARITY;
- if (!parodd)
- lcr |= UART_LCR_EPAR;
- }
-
- /* Set stop bits */
- if (stop_bits)
- lcr |= UART_LCR_STOP /* 2 stop bits */ ;
-
- writeb(lcr, &port->ip_uart_regs->i4u_lcr);
-
- /* Re-enable the DMA interface if necessary */
- if (port->ip_sscr & IOC4_SSCR_DMA_EN) {
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
- port->ip_baud = baud;
-
- /* When we get within this number of ring entries of filling the
- * entire ring on tx, place an EXPLICIT intr to generate a lowat
- * notification when output has drained.
- */
- port->ip_tx_lowat = (TX_LOWAT_CHARS(baud) + 3) / 4;
- if (port->ip_tx_lowat == 0)
- port->ip_tx_lowat = 1;
-
- set_rx_timeout(port, 2);
-
- return 0;
-}
-
-/**
- * do_write - Write bytes to the port. Returns the number of bytes
- * actually written. Called from transmit_chars
- * @port: port to use
- * @buf: the stuff to write
- * @len: how many bytes in 'buf'
- */
-static inline int do_write(struct ioc4_port *port, char *buf, int len)
-{
- int prod_ptr, cons_ptr, total = 0;
- struct ring *outring;
- struct ring_entry *entry;
- struct hooks *hooks = port->ip_hooks;
-
- BUG_ON(!(len >= 0));
-
- prod_ptr = port->ip_tx_prod;
- cons_ptr = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
- outring = port->ip_outring;
-
- /* Maintain a 1-entry red-zone. The ring buffer is full when
- * (cons - prod) % ring_size is 1. Rather than do this subtraction
- * in the body of the loop, I'll do it now.
- */
- cons_ptr = (cons_ptr - (int)sizeof(struct ring_entry)) & PROD_CONS_MASK;
-
- /* Stuff the bytes into the output */
- while ((prod_ptr != cons_ptr) && (len > 0)) {
- int xx;
-
- /* Get 4 bytes (one ring entry) at a time */
- entry = (struct ring_entry *)((caddr_t) outring + prod_ptr);
-
- /* Invalidate all entries */
- entry->ring_allsc = 0;
-
- /* Copy in some bytes */
- for (xx = 0; (xx < 4) && (len > 0); xx++) {
- entry->ring_data[xx] = *buf++;
- entry->ring_sc[xx] = IOC4_TXCB_VALID;
- len--;
- total++;
- }
-
- /* If we are within some small threshold of filling up the
- * entire ring buffer, we must place an EXPLICIT intr here
- * to generate a lowat interrupt in case we subsequently
- * really do fill up the ring and the caller goes to sleep.
- * No need to place more than one though.
- */
- if (!(port->ip_flags & LOWAT_WRITTEN) &&
- ((cons_ptr - prod_ptr) & PROD_CONS_MASK)
- <= port->ip_tx_lowat
- * (int)sizeof(struct ring_entry)) {
- port->ip_flags |= LOWAT_WRITTEN;
- entry->ring_sc[0] |= IOC4_TXCB_INT_WHEN_DONE;
- }
-
- /* Go on to next entry */
- prod_ptr += sizeof(struct ring_entry);
- prod_ptr &= PROD_CONS_MASK;
- }
-
- /* If we sent something, start DMA if necessary */
- if (total > 0 && !(port->ip_sscr & IOC4_SSCR_DMA_EN)) {
- port->ip_sscr |= IOC4_SSCR_DMA_EN;
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
-
- /* Store the new producer pointer. If tx is disabled, we stuff the
- * data into the ring buffer, but we don't actually start tx.
- */
- if (!uart_tx_stopped(port->ip_port)) {
- writel(prod_ptr, &port->ip_serial_regs->stpir);
-
- /* If we are now transmitting, enable tx_mt interrupt so we
- * can disable DMA if necessary when the tx finishes.
- */
- if (total > 0)
- enable_intrs(port, hooks->intr_tx_mt);
- }
- port->ip_tx_prod = prod_ptr;
- return total;
-}
-
-/**
- * disable_intrs - disable interrupts
- * @port: port to enable
- * @mask: mask to use
- */
-static void disable_intrs(struct ioc4_port *port, uint32_t mask)
-{
- struct hooks *hooks = port->ip_hooks;
-
- if (port->ip_ienb & mask) {
- write_ireg(port->ip_ioc4_soft, mask, IOC4_W_IEC,
- IOC4_SIO_INTR_TYPE);
- port->ip_ienb &= ~mask;
- }
-
- if (!port->ip_ienb)
- write_ireg(port->ip_ioc4_soft, hooks->intr_dma_error,
- IOC4_W_IEC, IOC4_OTHER_INTR_TYPE);
-}
-
-/**
- * set_notification - Modify event notification
- * @port: port to use
- * @mask: events mask
- * @set_on: set ?
- */
-static int set_notification(struct ioc4_port *port, int mask, int set_on)
-{
- struct hooks *hooks = port->ip_hooks;
- uint32_t intrbits, sscrbits;
-
- BUG_ON(!mask);
-
- intrbits = sscrbits = 0;
-
- if (mask & N_DATA_READY)
- intrbits |= (hooks->intr_rx_timer | hooks->intr_rx_high);
- if (mask & N_OUTPUT_LOWAT)
- intrbits |= hooks->intr_tx_explicit;
- if (mask & N_DDCD) {
- intrbits |= hooks->intr_delta_dcd;
- sscrbits |= IOC4_SSCR_RX_RING_DCD;
- }
- if (mask & N_DCTS)
- intrbits |= hooks->intr_delta_cts;
-
- if (set_on) {
- enable_intrs(port, intrbits);
- port->ip_notify |= mask;
- port->ip_sscr |= sscrbits;
- } else {
- disable_intrs(port, intrbits);
- port->ip_notify &= ~mask;
- port->ip_sscr &= ~sscrbits;
- }
-
- /* We require DMA if either DATA_READY or DDCD notification is
- * currently requested. If neither of these is requested and
- * there is currently no tx in progress, DMA may be disabled.
- */
- if (port->ip_notify & (N_DATA_READY | N_DDCD))
- port->ip_sscr |= IOC4_SSCR_DMA_EN;
- else if (!(port->ip_ienb & hooks->intr_tx_mt))
- port->ip_sscr &= ~IOC4_SSCR_DMA_EN;
-
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- return 0;
-}
-
-/**
- * set_mcr - set the master control reg
- * @the_port: port to use
- * @mask1: mcr mask
- * @mask2: shadow mask
- */
-static inline int set_mcr(struct uart_port *the_port,
- int mask1, int mask2)
-{
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
- uint32_t shadow;
- int spiniter = 0;
- char mcr;
-
- if (!port)
- return -1;
-
- /* Pause the DMA interface if necessary */
- if (port->ip_sscr & IOC4_SSCR_DMA_EN) {
- writel(port->ip_sscr | IOC4_SSCR_DMA_PAUSE,
- &port->ip_serial_regs->sscr);
- while ((readl(&port->ip_serial_regs->sscr)
- & IOC4_SSCR_PAUSE_STATE) == 0) {
- spiniter++;
- if (spiniter > MAXITER)
- return -1;
- }
- }
- shadow = readl(&port->ip_serial_regs->shadow);
- mcr = (shadow & 0xff000000) >> 24;
-
- /* Set new value */
- mcr |= mask1;
- shadow |= mask2;
-
- writeb(mcr, &port->ip_uart_regs->i4u_mcr);
- writel(shadow, &port->ip_serial_regs->shadow);
-
- /* Re-enable the DMA interface if necessary */
- if (port->ip_sscr & IOC4_SSCR_DMA_EN) {
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
- return 0;
-}
-
-/**
- * ioc4_set_proto - set the protocol for the port
- * @port: port to use
- * @proto: protocol to use
- */
-static int ioc4_set_proto(struct ioc4_port *port, int proto)
-{
- struct hooks *hooks = port->ip_hooks;
-
- switch (proto) {
- case PROTO_RS232:
- /* Clear the appropriate GIO pin */
- writel(0, (&port->ip_mem->gppr[hooks->rs422_select_pin].raw));
- break;
-
- case PROTO_RS422:
- /* Set the appropriate GIO pin */
- writel(1, (&port->ip_mem->gppr[hooks->rs422_select_pin].raw));
- break;
-
- default:
- return 1;
- }
- return 0;
-}
-
-/**
- * transmit_chars - upper level write, called with ip_lock
- * @the_port: port to write
- */
-static void transmit_chars(struct uart_port *the_port)
-{
- int xmit_count, tail, head;
- int result;
- char *start;
- struct tty_struct *tty;
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
- struct uart_state *state;
-
- if (!the_port)
- return;
- if (!port)
- return;
-
- state = the_port->state;
- tty = state->port.tty;
-
- if (uart_circ_empty(&state->xmit) || uart_tx_stopped(the_port)) {
- /* Nothing to do or hw stopped */
- set_notification(port, N_ALL_OUTPUT, 0);
- return;
- }
-
- head = state->xmit.head;
- tail = state->xmit.tail;
- start = (char *)&state->xmit.buf[tail];
-
- /* write out all the data or until the end of the buffer */
- xmit_count = (head < tail) ? (UART_XMIT_SIZE - tail) : (head - tail);
- if (xmit_count > 0) {
- result = do_write(port, start, xmit_count);
- if (result > 0) {
- /* booking */
- xmit_count -= result;
- the_port->icount.tx += result;
- /* advance the pointers */
- tail += result;
- tail &= UART_XMIT_SIZE - 1;
- state->xmit.tail = tail;
- start = (char *)&state->xmit.buf[tail];
- }
- }
- if (uart_circ_chars_pending(&state->xmit) < WAKEUP_CHARS)
- uart_write_wakeup(the_port);
-
- if (uart_circ_empty(&state->xmit)) {
- set_notification(port, N_OUTPUT_LOWAT, 0);
- } else {
- set_notification(port, N_OUTPUT_LOWAT, 1);
- }
-}
-
-/**
- * ioc4_change_speed - change the speed of the port
- * @the_port: port to change
- * @new_termios: new termios settings
- * @old_termios: old termios settings
- */
-static void
-ioc4_change_speed(struct uart_port *the_port,
- struct ktermios *new_termios, struct ktermios *old_termios)
-{
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
- int baud, bits;
- unsigned cflag, iflag;
- int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
- struct uart_state *state = the_port->state;
-
- cflag = new_termios->c_cflag;
- iflag = new_termios->c_iflag;
-
- switch (cflag & CSIZE) {
- case CS5:
- new_data = 5;
- bits = 7;
- break;
- case CS6:
- new_data = 6;
- bits = 8;
- break;
- case CS7:
- new_data = 7;
- bits = 9;
- break;
- case CS8:
- new_data = 8;
- bits = 10;
- break;
- default:
- /* cuz we always need a default ... */
- new_data = 5;
- bits = 7;
- break;
- }
- if (cflag & CSTOPB) {
- bits++;
- new_stop = 1;
- }
- if (cflag & PARENB) {
- bits++;
- new_parity_enable = 1;
- if (cflag & PARODD)
- new_parity = 1;
- }
- baud = uart_get_baud_rate(the_port, new_termios, old_termios,
- MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED);
- DPRINT_CONFIG(("%s: returned baud %d\n", __func__, baud));
-
- /* default is 9600 */
- if (!baud)
- baud = 9600;
-
- if (!the_port->fifosize)
- the_port->fifosize = IOC4_FIFO_CHARS;
- the_port->timeout = ((the_port->fifosize * HZ * bits) / (baud / 10));
- the_port->timeout += HZ / 50; /* Add .02 seconds of slop */
-
- the_port->ignore_status_mask = N_ALL_INPUT;
-
- state->port.low_latency = 1;
-
- if (iflag & IGNPAR)
- the_port->ignore_status_mask &= ~(N_PARITY_ERROR
- | N_FRAMING_ERROR);
- if (iflag & IGNBRK) {
- the_port->ignore_status_mask &= ~N_BREAK;
- if (iflag & IGNPAR)
- the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
- }
- if (!(cflag & CREAD)) {
- /* ignore everything */
- the_port->ignore_status_mask &= ~N_DATA_READY;
- }
-
- if (cflag & CRTSCTS) {
- port->ip_sscr |= IOC4_SSCR_HFC_EN;
- }
- else {
- port->ip_sscr &= ~IOC4_SSCR_HFC_EN;
- }
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
-
- /* Set the configuration and proper notification call */
- DPRINT_CONFIG(("%s : port 0x%p cflag 0%o "
- "config_port(baud %d data %d stop %d p enable %d parity %d),"
- " notification 0x%x\n",
- __func__, (void *)port, cflag, baud, new_data, new_stop,
- new_parity_enable, new_parity, the_port->ignore_status_mask));
-
- if ((config_port(port, baud, /* baud */
- new_data, /* byte size */
- new_stop, /* stop bits */
- new_parity_enable, /* set parity */
- new_parity)) >= 0) { /* parity 1==odd */
- set_notification(port, the_port->ignore_status_mask, 1);
- }
-}
-
-/**
- * ic4_startup_local - Start up the serial port - returns >= 0 if no errors
- * @the_port: Port to operate on
- */
-static inline int ic4_startup_local(struct uart_port *the_port)
-{
- struct ioc4_port *port;
- struct uart_state *state;
-
- if (!the_port)
- return -1;
-
- port = get_ioc4_port(the_port, 0);
- if (!port)
- return -1;
-
- state = the_port->state;
-
- local_open(port);
-
- /* set the protocol - mapbase has the port type */
- ioc4_set_proto(port, the_port->mapbase);
-
- /* set the speed of the serial port */
- ioc4_change_speed(the_port, &state->port.tty->termios,
- (struct ktermios *)0);
-
- return 0;
-}
-
-/*
- * ioc4_cb_output_lowat - called when the output low water mark is hit
- * @the_port: port to output
- */
-static void ioc4_cb_output_lowat(struct uart_port *the_port)
-{
- unsigned long pflags;
-
- /* ip_lock is set on the call here */
- if (the_port) {
- spin_lock_irqsave(&the_port->lock, pflags);
- transmit_chars(the_port);
- spin_unlock_irqrestore(&the_port->lock, pflags);
- }
-}
-
-/**
- * handle_intr - service any interrupts for the given port - 2nd level
- * called via sd_intr
- * @arg: handler arg
- * @sio_ir: ioc4regs
- */
-static void handle_intr(void *arg, uint32_t sio_ir)
-{
- struct ioc4_port *port = (struct ioc4_port *)arg;
- struct hooks *hooks = port->ip_hooks;
- unsigned int rx_high_rd_aborted = 0;
- unsigned long flags;
- struct uart_port *the_port;
- int loop_counter;
-
- /* Possible race condition here: The tx_mt interrupt bit may be
- * cleared without the intervention of the interrupt handler,
- * e.g. by a write. If the top level interrupt handler reads a
- * tx_mt, then some other processor does a write, starting up
- * output, then we come in here, see the tx_mt and stop DMA, the
- * output started by the other processor will hang. Thus we can
- * only rely on tx_mt being legitimate if it is read while the
- * port lock is held. Therefore this bit must be ignored in the
- * passed in interrupt mask which was read by the top level
- * interrupt handler since the port lock was not held at the time
- * it was read. We can only rely on this bit being accurate if it
- * is read while the port lock is held. So we'll clear it for now,
- * and reload it later once we have the port lock.
- */
- sio_ir &= ~(hooks->intr_tx_mt);
-
- spin_lock_irqsave(&port->ip_lock, flags);
-
- loop_counter = MAXITER; /* to avoid hangs */
-
- do {
- uint32_t shadow;
-
- if ( loop_counter-- <= 0 ) {
- printk(KERN_WARNING "IOC4 serial: "
- "possible hang condition/"
- "port stuck on interrupt.\n");
- break;
- }
-
- /* Handle a DCD change */
- if (sio_ir & hooks->intr_delta_dcd) {
- /* ACK the interrupt */
- writel(hooks->intr_delta_dcd,
- &port->ip_mem->sio_ir.raw);
-
- shadow = readl(&port->ip_serial_regs->shadow);
-
- if ((port->ip_notify & N_DDCD)
- && (shadow & IOC4_SHADOW_DCD)
- && (port->ip_port)) {
- the_port = port->ip_port;
- the_port->icount.dcd = 1;
- wake_up_interruptible
- (&the_port->state->port.delta_msr_wait);
- } else if ((port->ip_notify & N_DDCD)
- && !(shadow & IOC4_SHADOW_DCD)) {
- /* Flag delta DCD/no DCD */
- port->ip_flags |= DCD_ON;
- }
- }
-
- /* Handle a CTS change */
- if (sio_ir & hooks->intr_delta_cts) {
- /* ACK the interrupt */
- writel(hooks->intr_delta_cts,
- &port->ip_mem->sio_ir.raw);
-
- shadow = readl(&port->ip_serial_regs->shadow);
-
- if ((port->ip_notify & N_DCTS)
- && (port->ip_port)) {
- the_port = port->ip_port;
- the_port->icount.cts =
- (shadow & IOC4_SHADOW_CTS) ? 1 : 0;
- wake_up_interruptible
- (&the_port->state->port.delta_msr_wait);
- }
- }
-
- /* rx timeout interrupt. Must be some data available. Put this
- * before the check for rx_high since servicing this condition
- * may cause that condition to clear.
- */
- if (sio_ir & hooks->intr_rx_timer) {
- /* ACK the interrupt */
- writel(hooks->intr_rx_timer,
- &port->ip_mem->sio_ir.raw);
-
- if ((port->ip_notify & N_DATA_READY)
- && (port->ip_port)) {
- /* ip_lock is set on call here */
- receive_chars(port->ip_port);
- }
- }
-
- /* rx high interrupt. Must be after rx_timer. */
- else if (sio_ir & hooks->intr_rx_high) {
- /* Data available, notify upper layer */
- if ((port->ip_notify & N_DATA_READY)
- && port->ip_port) {
- /* ip_lock is set on call here */
- receive_chars(port->ip_port);
- }
-
- /* We can't ACK this interrupt. If receive_chars didn't
- * cause the condition to clear, we'll have to disable
- * the interrupt until the data is drained.
- * If the read was aborted, don't disable the interrupt
- * as this may cause us to hang indefinitely. An
- * aborted read generally means that this interrupt
- * hasn't been delivered to the cpu yet anyway, even
- * though we see it as asserted when we read the sio_ir.
- */
- if ((sio_ir = PENDING(port)) & hooks->intr_rx_high) {
- if ((port->ip_flags & READ_ABORTED) == 0) {
- port->ip_ienb &= ~hooks->intr_rx_high;
- port->ip_flags |= INPUT_HIGH;
- } else {
- rx_high_rd_aborted++;
- }
- }
- }
-
- /* We got a low water interrupt: notify upper layer to
- * send more data. Must come before tx_mt since servicing
- * this condition may cause that condition to clear.
- */
- if (sio_ir & hooks->intr_tx_explicit) {
- port->ip_flags &= ~LOWAT_WRITTEN;
-
- /* ACK the interrupt */
- writel(hooks->intr_tx_explicit,
- &port->ip_mem->sio_ir.raw);
-
- if (port->ip_notify & N_OUTPUT_LOWAT)
- ioc4_cb_output_lowat(port->ip_port);
- }
-
- /* Handle tx_mt. Must come after tx_explicit. */
- else if (sio_ir & hooks->intr_tx_mt) {
- /* If we are expecting a lowat notification
- * and we get to this point it probably means that for
- * some reason the tx_explicit didn't work as expected
- * (that can legitimately happen if the output buffer is
- * filled up in just the right way).
- * So send the notification now.
- */
- if (port->ip_notify & N_OUTPUT_LOWAT) {
- ioc4_cb_output_lowat(port->ip_port);
-
- /* We need to reload the sio_ir since the lowat
- * call may have caused another write to occur,
- * clearing the tx_mt condition.
- */
- sio_ir = PENDING(port);
- }
-
- /* If the tx_mt condition still persists even after the
- * lowat call, we've got some work to do.
- */
- if (sio_ir & hooks->intr_tx_mt) {
-
- /* If we are not currently expecting DMA input,
- * and the transmitter has just gone idle,
- * there is no longer any reason for DMA, so
- * disable it.
- */
- if (!(port->ip_notify
- & (N_DATA_READY | N_DDCD))) {
- BUG_ON(!(port->ip_sscr
- & IOC4_SSCR_DMA_EN));
- port->ip_sscr &= ~IOC4_SSCR_DMA_EN;
- writel(port->ip_sscr,
- &port->ip_serial_regs->sscr);
- }
-
- /* Prevent infinite tx_mt interrupt */
- port->ip_ienb &= ~hooks->intr_tx_mt;
- }
- }
- sio_ir = PENDING(port);
-
- /* if the read was aborted and only hooks->intr_rx_high,
- * clear hooks->intr_rx_high, so we do not loop forever.
- */
-
- if (rx_high_rd_aborted && (sio_ir == hooks->intr_rx_high)) {
- sio_ir &= ~hooks->intr_rx_high;
- }
- } while (sio_ir & hooks->intr_all);
-
- spin_unlock_irqrestore(&port->ip_lock, flags);
-
- /* Re-enable interrupts before returning from interrupt handler.
- * Getting interrupted here is okay. It'll just v() our semaphore, and
- * we'll come through the loop again.
- */
-
- write_ireg(port->ip_ioc4_soft, port->ip_ienb, IOC4_W_IES,
- IOC4_SIO_INTR_TYPE);
-}
-
-/*
- * ioc4_cb_post_ncs - called for some basic errors
- * @port: port to use
- * @ncs: event
- */
-static void ioc4_cb_post_ncs(struct uart_port *the_port, int ncs)
-{
- struct uart_icount *icount;
-
- icount = &the_port->icount;
-
- if (ncs & NCS_BREAK)
- icount->brk++;
- if (ncs & NCS_FRAMING)
- icount->frame++;
- if (ncs & NCS_OVERRUN)
- icount->overrun++;
- if (ncs & NCS_PARITY)
- icount->parity++;
-}
-
-/**
- * do_read - Read in bytes from the port. Return the number of bytes
- * actually read.
- * @the_port: port to use
- * @buf: place to put the stuff we read
- * @len: how big 'buf' is
- */
-
-static inline int do_read(struct uart_port *the_port, unsigned char *buf,
- int len)
-{
- int prod_ptr, cons_ptr, total;
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
- struct ring *inring;
- struct ring_entry *entry;
- struct hooks *hooks;
- int byte_num;
- char *sc;
- int loop_counter;
-
- BUG_ON(!(len >= 0));
- BUG_ON(!port);
- hooks = port->ip_hooks;
-
- /* There is a nasty timing issue in the IOC4. When the rx_timer
- * expires or the rx_high condition arises, we take an interrupt.
- * At some point while servicing the interrupt, we read bytes from
- * the ring buffer and re-arm the rx_timer. However the rx_timer is
- * not started until the first byte is received *after* it is armed,
- * and any bytes pending in the rx construction buffers are not drained
- * to memory until either there are 4 bytes available or the rx_timer
- * expires. This leads to a potential situation where data is left
- * in the construction buffers forever - 1 to 3 bytes were received
- * after the interrupt was generated but before the rx_timer was
- * re-armed. At that point as long as no subsequent bytes are received
- * the timer will never be started and the bytes will remain in the
- * construction buffer forever. The solution is to execute a DRAIN
- * command after rearming the timer. This way any bytes received before
- * the DRAIN will be drained to memory, and any bytes received after
- * the DRAIN will start the TIMER and be drained when it expires.
- * Luckily, this only needs to be done when the DMA buffer is empty
- * since there is no requirement that this function return all
- * available data as long as it returns some.
- */
- /* Re-arm the timer */
- writel(port->ip_rx_cons | IOC4_SRCIR_ARM, &port->ip_serial_regs->srcir);
-
- prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
- cons_ptr = port->ip_rx_cons;
-
- if (prod_ptr == cons_ptr) {
- int reset_dma = 0;
-
- /* Input buffer appears empty, do a flush. */
-
- /* DMA must be enabled for this to work. */
- if (!(port->ip_sscr & IOC4_SSCR_DMA_EN)) {
- port->ip_sscr |= IOC4_SSCR_DMA_EN;
- reset_dma = 1;
- }
-
- /* Potential race condition: we must reload the srpir after
- * issuing the drain command, otherwise we could think the rx
- * buffer is empty, then take a very long interrupt, and when
- * we come back it's full and we wait forever for the drain to
- * complete.
- */
- writel(port->ip_sscr | IOC4_SSCR_RX_DRAIN,
- &port->ip_serial_regs->sscr);
- prod_ptr = readl(&port->ip_serial_regs->srpir)
- & PROD_CONS_MASK;
-
- /* We must not wait for the DRAIN to complete unless there are
- * at least 8 bytes (2 ring entries) available to receive the
- * data otherwise the DRAIN will never complete and we'll
- * deadlock here.
- * In fact, to make things easier, I'll just ignore the flush if
- * there is any data at all now available.
- */
- if (prod_ptr == cons_ptr) {
- loop_counter = 0;
- while (readl(&port->ip_serial_regs->sscr) &
- IOC4_SSCR_RX_DRAIN) {
- loop_counter++;
- if (loop_counter > MAXITER)
- return -1;
- }
-
- /* SIGH. We have to reload the prod_ptr *again* since
- * the drain may have caused it to change
- */
- prod_ptr = readl(&port->ip_serial_regs->srpir)
- & PROD_CONS_MASK;
- }
- if (reset_dma) {
- port->ip_sscr &= ~IOC4_SSCR_DMA_EN;
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
- }
- inring = port->ip_inring;
- port->ip_flags &= ~READ_ABORTED;
-
- total = 0;
- loop_counter = 0xfffff; /* to avoid hangs */
-
- /* Grab bytes from the hardware */
- while ((prod_ptr != cons_ptr) && (len > 0)) {
- entry = (struct ring_entry *)((caddr_t)inring + cons_ptr);
-
- if ( loop_counter-- <= 0 ) {
- printk(KERN_WARNING "IOC4 serial: "
- "possible hang condition/"
- "port stuck on read.\n");
- break;
- }
-
- /* According to the producer pointer, this ring entry
- * must contain some data. But if the PIO happened faster
- * than the DMA, the data may not be available yet, so let's
- * wait until it arrives.
- */
- if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
- /* Indicate the read is aborted so we don't disable
- * the interrupt thinking that the consumer is
- * congested.
- */
- port->ip_flags |= READ_ABORTED;
- len = 0;
- break;
- }
-
- /* Load the bytes/status out of the ring entry */
- for (byte_num = 0; byte_num < 4 && len > 0; byte_num++) {
- sc = &(entry->ring_sc[byte_num]);
-
- /* Check for change in modem state or overrun */
- if ((*sc & IOC4_RXSB_MODEM_VALID)
- && (port->ip_notify & N_DDCD)) {
- /* Notify upper layer if DCD dropped */
-
- if ((port->ip_flags & DCD_ON)
- && !(*sc & IOC4_RXSB_DCD)) {
-
- /* If we have already copied some data,
- * return it. We'll pick up the carrier
- * drop on the next pass. That way we
- * don't throw away the data that has
- * already been copied back to
- * the caller's buffer.
- */
- if (total > 0) {
- len = 0;
- break;
- }
- port->ip_flags &= ~DCD_ON;
-
- /* Turn off this notification so the
- * carrier drop protocol won't see it
- * again when it does a read.
- */
- *sc &= ~IOC4_RXSB_MODEM_VALID;
-
- /* To keep things consistent, we need
- * to update the consumer pointer so
- * the next reader won't come in and
- * try to read the same ring entries
- * again. This must be done here before
- * the dcd change.
- */
-
- if ((entry->ring_allsc & RING_ANY_VALID)
- == 0) {
- cons_ptr += (int)sizeof
- (struct ring_entry);
- cons_ptr &= PROD_CONS_MASK;
- }
- writel(cons_ptr,
- &port->ip_serial_regs->srcir);
- port->ip_rx_cons = cons_ptr;
-
- /* Notify upper layer of carrier drop */
- if ((port->ip_notify & N_DDCD)
- && port->ip_port) {
- the_port->icount.dcd = 0;
- wake_up_interruptible
- (&the_port->state->
- port.delta_msr_wait);
- }
-
- /* If we had any data to return, we
- * would have returned it above.
- */
- return 0;
- }
- }
- if (*sc & IOC4_RXSB_MODEM_VALID) {
- /* Notify that an input overrun occurred */
- if ((*sc & IOC4_RXSB_OVERRUN)
- && (port->ip_notify & N_OVERRUN_ERROR)) {
- ioc4_cb_post_ncs(the_port, NCS_OVERRUN);
- }
- /* Don't look at this byte again */
- *sc &= ~IOC4_RXSB_MODEM_VALID;
- }
-
- /* Check for valid data or RX errors */
- if ((*sc & IOC4_RXSB_DATA_VALID) &&
- ((*sc & (IOC4_RXSB_PAR_ERR
- | IOC4_RXSB_FRAME_ERR
- | IOC4_RXSB_BREAK))
- && (port->ip_notify & (N_PARITY_ERROR
- | N_FRAMING_ERROR
- | N_BREAK)))) {
- /* There is an error condition on the next byte.
- * If we have already transferred some bytes,
- * we'll stop here. Otherwise if this is the
- * first byte to be read, we'll just transfer
- * it alone after notifying the
- * upper layer of its status.
- */
- if (total > 0) {
- len = 0;
- break;
- } else {
- if ((*sc & IOC4_RXSB_PAR_ERR) &&
- (port->ip_notify & N_PARITY_ERROR)) {
- ioc4_cb_post_ncs(the_port,
- NCS_PARITY);
- }
- if ((*sc & IOC4_RXSB_FRAME_ERR) &&
- (port->ip_notify & N_FRAMING_ERROR)){
- ioc4_cb_post_ncs(the_port,
- NCS_FRAMING);
- }
- if ((*sc & IOC4_RXSB_BREAK)
- && (port->ip_notify & N_BREAK)) {
- ioc4_cb_post_ncs
- (the_port,
- NCS_BREAK);
- }
- len = 1;
- }
- }
- if (*sc & IOC4_RXSB_DATA_VALID) {
- *sc &= ~IOC4_RXSB_DATA_VALID;
- *buf = entry->ring_data[byte_num];
- buf++;
- len--;
- total++;
- }
- }
-
- /* If we used up this entry entirely, go on to the next one,
- * otherwise we must have run out of buffer space, so
- * leave the consumer pointer here for the next read in case
- * there are still unread bytes in this entry.
- */
- if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
- cons_ptr += (int)sizeof(struct ring_entry);
- cons_ptr &= PROD_CONS_MASK;
- }
- }
-
- /* Update consumer pointer and re-arm rx timer interrupt */
- writel(cons_ptr, &port->ip_serial_regs->srcir);
- port->ip_rx_cons = cons_ptr;
-
- /* If we have now dipped below the rx high water mark and we have
- * rx_high interrupt turned off, we can now turn it back on again.
- */
- if ((port->ip_flags & INPUT_HIGH) && (((prod_ptr - cons_ptr)
- & PROD_CONS_MASK) < ((port->ip_sscr &
- IOC4_SSCR_RX_THRESHOLD)
- << IOC4_PROD_CONS_PTR_OFF))) {
- port->ip_flags &= ~INPUT_HIGH;
- enable_intrs(port, hooks->intr_rx_high);
- }
- return total;
-}
-
-/**
- * receive_chars - upper level read. Called with ip_lock.
- * @the_port: port to read from
- */
-static void receive_chars(struct uart_port *the_port)
-{
- unsigned char ch[IOC4_MAX_CHARS];
- int read_count, request_count = IOC4_MAX_CHARS;
- struct uart_icount *icount;
- struct uart_state *state = the_port->state;
- unsigned long pflags;
-
- /* Make sure all the pointers are "good" ones */
- if (!state)
- return;
-
- spin_lock_irqsave(&the_port->lock, pflags);
-
- request_count = tty_buffer_request_room(&state->port, IOC4_MAX_CHARS);
-
- if (request_count > 0) {
- icount = &the_port->icount;
- read_count = do_read(the_port, ch, request_count);
- if (read_count > 0) {
- tty_insert_flip_string(&state->port, ch, read_count);
- icount->rx += read_count;
- }
- }
-
- spin_unlock_irqrestore(&the_port->lock, pflags);
-
- tty_flip_buffer_push(&state->port);
-}
-
-/**
- * ic4_type - What type of console are we?
- * @port: Port to operate with (we ignore since we only have one port)
- *
- */
-static const char *ic4_type(struct uart_port *the_port)
-{
- if (the_port->mapbase == PROTO_RS232)
- return "SGI IOC4 Serial [rs232]";
- else
- return "SGI IOC4 Serial [rs422]";
-}
-
-/**
- * ic4_tx_empty - Is the transmitter empty?
- * @port: Port to operate on
- *
- */
-static unsigned int ic4_tx_empty(struct uart_port *the_port)
-{
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
- unsigned int ret = 0;
-
- if (port_is_active(port, the_port)) {
- if (readl(&port->ip_serial_regs->shadow) & IOC4_SHADOW_TEMT)
- ret = TIOCSER_TEMT;
- }
- return ret;
-}
-
-/**
- * ic4_stop_tx - stop the transmitter
- * @port: Port to operate on
- *
- */
-static void ic4_stop_tx(struct uart_port *the_port)
-{
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
-
- if (port_is_active(port, the_port))
- set_notification(port, N_OUTPUT_LOWAT, 0);
-}
-
-/**
- * null_void_function -
- * @port: Port to operate on
- *
- */
-static void null_void_function(struct uart_port *the_port)
-{
-}
-
-/**
- * ic4_shutdown - shut down the port - free irq and disable
- * @port: Port to shut down
- *
- */
-static void ic4_shutdown(struct uart_port *the_port)
-{
- unsigned long port_flags;
- struct ioc4_port *port;
- struct uart_state *state;
-
- port = get_ioc4_port(the_port, 0);
- if (!port)
- return;
-
- state = the_port->state;
- port->ip_port = NULL;
-
- wake_up_interruptible(&state->port.delta_msr_wait);
-
- if (state->port.tty)
- set_bit(TTY_IO_ERROR, &state->port.tty->flags);
-
- spin_lock_irqsave(&the_port->lock, port_flags);
- set_notification(port, N_ALL, 0);
- port->ip_flags = PORT_INACTIVE;
- spin_unlock_irqrestore(&the_port->lock, port_flags);
-}
-
-/**
- * ic4_set_mctrl - set control lines (dtr, rts, etc)
- * @port: Port to operate on
- * @mctrl: Lines to set/unset
- *
- */
-static void ic4_set_mctrl(struct uart_port *the_port, unsigned int mctrl)
-{
- unsigned char mcr = 0;
- struct ioc4_port *port;
-
- port = get_ioc4_port(the_port, 0);
- if (!port_is_active(port, the_port))
- return;
-
- if (mctrl & TIOCM_RTS)
- mcr |= UART_MCR_RTS;
- if (mctrl & TIOCM_DTR)
- mcr |= UART_MCR_DTR;
- if (mctrl & TIOCM_OUT1)
- mcr |= UART_MCR_OUT1;
- if (mctrl & TIOCM_OUT2)
- mcr |= UART_MCR_OUT2;
- if (mctrl & TIOCM_LOOP)
- mcr |= UART_MCR_LOOP;
-
- set_mcr(the_port, mcr, IOC4_SHADOW_DTR);
-}
-
-/**
- * ic4_get_mctrl - get control line info
- * @port: port to operate on
- *
- */
-static unsigned int ic4_get_mctrl(struct uart_port *the_port)
-{
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
- uint32_t shadow;
- unsigned int ret = 0;
-
- if (!port_is_active(port, the_port))
- return 0;
-
- shadow = readl(&port->ip_serial_regs->shadow);
- if (shadow & IOC4_SHADOW_DCD)
- ret |= TIOCM_CAR;
- if (shadow & IOC4_SHADOW_DR)
- ret |= TIOCM_DSR;
- if (shadow & IOC4_SHADOW_CTS)
- ret |= TIOCM_CTS;
- return ret;
-}
-
-/**
- * ic4_start_tx - Start transmitter, flush any output
- * @port: Port to operate on
- *
- */
-static void ic4_start_tx(struct uart_port *the_port)
-{
- struct ioc4_port *port = get_ioc4_port(the_port, 0);
-
- if (port_is_active(port, the_port)) {
- set_notification(port, N_OUTPUT_LOWAT, 1);
- enable_intrs(port, port->ip_hooks->intr_tx_mt);
- }
-}
-
-/**
- * ic4_break_ctl - handle breaks
- * @port: Port to operate on
- * @break_state: Break state
- *
- */
-static void ic4_break_ctl(struct uart_port *the_port, int break_state)
-{
-}
-
-/**
- * ic4_startup - Start up the serial port
- * @port: Port to operate on
- *
- */
-static int ic4_startup(struct uart_port *the_port)
-{
- int retval;
- struct ioc4_port *port;
- struct ioc4_control *control;
- struct uart_state *state;
- unsigned long port_flags;
-
- if (!the_port)
- return -ENODEV;
- port = get_ioc4_port(the_port, 1);
- if (!port)
- return -ENODEV;
- state = the_port->state;
-
- control = port->ip_control;
- if (!control) {
- port->ip_port = NULL;
- return -ENODEV;
- }
-
- /* Start up the serial port */
- spin_lock_irqsave(&the_port->lock, port_flags);
- retval = ic4_startup_local(the_port);
- spin_unlock_irqrestore(&the_port->lock, port_flags);
- return retval;
-}
-
-/**
- * ic4_set_termios - set termios stuff
- * @port: port to operate on
- * @termios: New settings
- * @termios: Old
- *
- */
-static void
-ic4_set_termios(struct uart_port *the_port,
- struct ktermios *termios, struct ktermios *old_termios)
-{
- unsigned long port_flags;
-
- spin_lock_irqsave(&the_port->lock, port_flags);
- ioc4_change_speed(the_port, termios, old_termios);
- spin_unlock_irqrestore(&the_port->lock, port_flags);
-}
-
-/**
- * ic4_request_port - allocate resources for port - no op....
- * @port: port to operate on
- *
- */
-static int ic4_request_port(struct uart_port *port)
-{
- return 0;
-}
-
-/* Associate the uart functions above - given to serial core */
-
-static const struct uart_ops ioc4_ops = {
- .tx_empty = ic4_tx_empty,
- .set_mctrl = ic4_set_mctrl,
- .get_mctrl = ic4_get_mctrl,
- .stop_tx = ic4_stop_tx,
- .start_tx = ic4_start_tx,
- .stop_rx = null_void_function,
- .break_ctl = ic4_break_ctl,
- .startup = ic4_startup,
- .shutdown = ic4_shutdown,
- .set_termios = ic4_set_termios,
- .type = ic4_type,
- .release_port = null_void_function,
- .request_port = ic4_request_port,
-};
-
-/*
- * Boot-time initialization code
- */
-
-static struct uart_driver ioc4_uart_rs232 = {
- .owner = THIS_MODULE,
- .driver_name = "ioc4_serial_rs232",
- .dev_name = DEVICE_NAME_RS232,
- .major = DEVICE_MAJOR,
- .minor = DEVICE_MINOR_RS232,
- .nr = IOC4_NUM_CARDS * IOC4_NUM_SERIAL_PORTS,
-};
-
-static struct uart_driver ioc4_uart_rs422 = {
- .owner = THIS_MODULE,
- .driver_name = "ioc4_serial_rs422",
- .dev_name = DEVICE_NAME_RS422,
- .major = DEVICE_MAJOR,
- .minor = DEVICE_MINOR_RS422,
- .nr = IOC4_NUM_CARDS * IOC4_NUM_SERIAL_PORTS,
-};
-
-
-/**
- * ioc4_serial_remove_one - detach function
- *
- * @idd: IOC4 master module data for this IOC4
- */
-
-static int ioc4_serial_remove_one(struct ioc4_driver_data *idd)
-{
- int port_num, port_type;
- struct ioc4_control *control;
- struct uart_port *the_port;
- struct ioc4_port *port;
- struct ioc4_soft *soft;
-
- /* If serial driver did not attach, don't try to detach */
- control = idd->idd_serial_data;
- if (!control)
- return 0;
-
- for (port_num = 0; port_num < IOC4_NUM_SERIAL_PORTS; port_num++) {
- for (port_type = UART_PORT_MIN;
- port_type < UART_PORT_COUNT;
- port_type++) {
- the_port = &control->ic_port[port_num].icp_uart_port
- [port_type];
- if (the_port) {
- switch (port_type) {
- case UART_PORT_RS422:
- uart_remove_one_port(&ioc4_uart_rs422,
- the_port);
- break;
- default:
- case UART_PORT_RS232:
- uart_remove_one_port(&ioc4_uart_rs232,
- the_port);
- break;
- }
- }
- }
- port = control->ic_port[port_num].icp_port;
- /* we allocate in pairs */
- if (!(port_num & 1) && port) {
- pci_free_consistent(port->ip_pdev,
- TOTAL_RING_BUF_SIZE,
- port->ip_cpu_ringbuf,
- port->ip_dma_ringbuf);
- kfree(port);
- }
- }
- soft = control->ic_soft;
- if (soft) {
- free_irq(control->ic_irq, soft);
- if (soft->is_ioc4_serial_addr) {
- iounmap(soft->is_ioc4_serial_addr);
- release_mem_region((unsigned long)
- soft->is_ioc4_serial_addr,
- sizeof(struct ioc4_serial));
- }
- kfree(soft);
- }
- kfree(control);
- idd->idd_serial_data = NULL;
-
- return 0;
-}
-
-
-/**
- * ioc4_serial_core_attach_rs232 - register with serial core
- * This is done during pci probing
- * @pdev: handle for this card
- */
-static inline int
-ioc4_serial_core_attach(struct pci_dev *pdev, int port_type)
-{
- struct ioc4_port *port;
- struct uart_port *the_port;
- struct ioc4_driver_data *idd = pci_get_drvdata(pdev);
- struct ioc4_control *control = idd->idd_serial_data;
- int port_num;
- int port_type_idx;
- struct uart_driver *u_driver;
-
-
- DPRINT_CONFIG(("%s: attach pdev 0x%p - control 0x%p\n",
- __func__, pdev, (void *)control));
-
- if (!control)
- return -ENODEV;
-
- port_type_idx = (port_type == PROTO_RS232) ? UART_PORT_RS232
- : UART_PORT_RS422;
-
- u_driver = (port_type == PROTO_RS232) ? &ioc4_uart_rs232
- : &ioc4_uart_rs422;
-
- /* once around for each port on this card */
- for (port_num = 0; port_num < IOC4_NUM_SERIAL_PORTS; port_num++) {
- the_port = &control->ic_port[port_num].icp_uart_port
- [port_type_idx];
- port = control->ic_port[port_num].icp_port;
- port->ip_all_ports[port_type_idx] = the_port;
-
- DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p : type %s\n",
- __func__, (void *)the_port,
- (void *)port,
- port_type == PROTO_RS232 ? "rs232" : "rs422"));
-
- /* membase, iobase and mapbase just need to be non-0 */
- the_port->membase = (unsigned char __iomem *)1;
- the_port->iobase = (pdev->bus->number << 16) | port_num;
- the_port->line = (Num_of_ioc4_cards << 2) | port_num;
- the_port->mapbase = port_type;
- the_port->type = PORT_16550A;
- the_port->fifosize = IOC4_FIFO_CHARS;
- the_port->ops = &ioc4_ops;
- the_port->irq = control->ic_irq;
- the_port->dev = &pdev->dev;
- spin_lock_init(&the_port->lock);
- if (uart_add_one_port(u_driver, the_port) < 0) {
- printk(KERN_WARNING
- "%s: unable to add port %d bus %d\n",
- __func__, the_port->line, pdev->bus->number);
- } else {
- DPRINT_CONFIG(
- ("IOC4 serial port %d irq = %d, bus %d\n",
- the_port->line, the_port->irq, pdev->bus->number));
- }
- }
- return 0;
-}
-
-/**
- * ioc4_serial_attach_one - register attach function
- * called per card found from IOC4 master module.
- * @idd: Master module data for this IOC4
- */
-static int
-ioc4_serial_attach_one(struct ioc4_driver_data *idd)
-{
- unsigned long tmp_addr1;
- struct ioc4_serial __iomem *serial;
- struct ioc4_soft *soft;
- struct ioc4_control *control;
- int ret = 0;
-
-
- DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, idd->idd_pdev,
- idd->idd_pci_id));
-
- /* PCI-RT does not bring out serial connections.
- * Do not attach to this particular IOC4.
- */
- if (idd->idd_variant == IOC4_VARIANT_PCI_RT)
- return 0;
-
- /* request serial registers */
- tmp_addr1 = idd->idd_bar0 + IOC4_SERIAL_OFFSET;
-
- if (!request_mem_region(tmp_addr1, sizeof(struct ioc4_serial),
- "sioc4_uart")) {
- printk(KERN_WARNING
- "ioc4 (%p): unable to get request region for "
- "uart space\n", (void *)idd->idd_pdev);
- ret = -ENODEV;
- goto out1;
- }
- serial = ioremap(tmp_addr1, sizeof(struct ioc4_serial));
- if (!serial) {
- printk(KERN_WARNING
- "ioc4 (%p) : unable to remap ioc4 serial register\n",
- (void *)idd->idd_pdev);
- ret = -ENODEV;
- goto out2;
- }
- DPRINT_CONFIG(("%s : mem 0x%p, serial 0x%p\n",
- __func__, (void *)idd->idd_misc_regs,
- (void *)serial));
-
- /* Get memory for the new card */
- control = kzalloc(sizeof(struct ioc4_control), GFP_KERNEL);
-
- if (!control) {
- printk(KERN_WARNING "ioc4_attach_one"
- ": unable to get memory for the IOC4\n");
- ret = -ENOMEM;
- goto out2;
- }
- idd->idd_serial_data = control;
-
- /* Allocate the soft structure */
- soft = kzalloc(sizeof(struct ioc4_soft), GFP_KERNEL);
- if (!soft) {
- printk(KERN_WARNING
- "ioc4 (%p): unable to get memory for the soft struct\n",
- (void *)idd->idd_pdev);
- ret = -ENOMEM;
- goto out3;
- }
-
- spin_lock_init(&soft->is_ir_lock);
- soft->is_ioc4_misc_addr = idd->idd_misc_regs;
- soft->is_ioc4_serial_addr = serial;
-
- /* Init the IOC4 */
- writel(0xf << IOC4_SIO_CR_CMD_PULSE_SHIFT,
- &idd->idd_misc_regs->sio_cr.raw);
-
- /* Enable serial port mode select generic PIO pins as outputs */
- writel(IOC4_GPCR_UART0_MODESEL | IOC4_GPCR_UART1_MODESEL
- | IOC4_GPCR_UART2_MODESEL | IOC4_GPCR_UART3_MODESEL,
- &idd->idd_misc_regs->gpcr_s.raw);
-
- /* Clear and disable all serial interrupts */
- write_ireg(soft, ~0, IOC4_W_IEC, IOC4_SIO_INTR_TYPE);
- writel(~0, &idd->idd_misc_regs->sio_ir.raw);
- write_ireg(soft, IOC4_OTHER_IR_SER_MEMERR, IOC4_W_IEC,
- IOC4_OTHER_INTR_TYPE);
- writel(IOC4_OTHER_IR_SER_MEMERR, &idd->idd_misc_regs->other_ir.raw);
- control->ic_soft = soft;
-
- /* Hook up interrupt handler */
- if (!request_irq(idd->idd_pdev->irq, ioc4_intr, IRQF_SHARED,
- "sgi-ioc4serial", soft)) {
- control->ic_irq = idd->idd_pdev->irq;
- } else {
- printk(KERN_WARNING
- "%s : request_irq fails for IRQ 0x%x\n ",
- __func__, idd->idd_pdev->irq);
- }
- ret = ioc4_attach_local(idd);
- if (ret)
- goto out4;
-
- /* register port with the serial core - 1 rs232, 1 rs422 */
-
- ret = ioc4_serial_core_attach(idd->idd_pdev, PROTO_RS232);
- if (ret)
- goto out4;
-
- ret = ioc4_serial_core_attach(idd->idd_pdev, PROTO_RS422);
- if (ret)
- goto out5;
-
- Num_of_ioc4_cards++;
-
- return ret;
-
- /* error exits that give back resources */
-out5:
- ioc4_serial_remove_one(idd);
- return ret;
-out4:
- kfree(soft);
-out3:
- kfree(control);
-out2:
- if (serial)
- iounmap(serial);
- release_mem_region(tmp_addr1, sizeof(struct ioc4_serial));
-out1:
-
- return ret;
-}
-
-
-static struct ioc4_submodule ioc4_serial_submodule = {
- .is_name = "IOC4_serial",
- .is_owner = THIS_MODULE,
- .is_probe = ioc4_serial_attach_one,
- .is_remove = ioc4_serial_remove_one,
-};
-
-/**
- * ioc4_serial_init - module init
- */
-static int __init ioc4_serial_init(void)
-{
- int ret;
-
- /* register with serial core */
- if ((ret = uart_register_driver(&ioc4_uart_rs232)) < 0) {
- printk(KERN_WARNING
- "%s: Couldn't register rs232 IOC4 serial driver\n",
- __func__);
- goto out;
- }
- if ((ret = uart_register_driver(&ioc4_uart_rs422)) < 0) {
- printk(KERN_WARNING
- "%s: Couldn't register rs422 IOC4 serial driver\n",
- __func__);
- goto out_uart_rs232;
- }
-
- /* register with IOC4 main module */
- ret = ioc4_register_submodule(&ioc4_serial_submodule);
- if (ret)
- goto out_uart_rs422;
- return 0;
-
-out_uart_rs422:
- uart_unregister_driver(&ioc4_uart_rs422);
-out_uart_rs232:
- uart_unregister_driver(&ioc4_uart_rs232);
-out:
- return ret;
-}
-
-static void __exit ioc4_serial_exit(void)
-{
- ioc4_unregister_submodule(&ioc4_serial_submodule);
- uart_unregister_driver(&ioc4_uart_rs232);
- uart_unregister_driver(&ioc4_uart_rs422);
-}
-
-late_initcall(ioc4_serial_init); /* Call only after tty init is done */
-module_exit(ioc4_serial_exit);
-
-MODULE_AUTHOR("Pat Gefre - Silicon Graphics Inc. (SGI) <pfg@....com>");
-MODULE_DESCRIPTION("Serial PCI driver module for SGI IOC4 Base-IO Card");
-MODULE_LICENSE("GPL");
--
2.20.1
Powered by blists - more mailing lists