Message-ID: <CA+E=qVd-hz68VhL0n+3-HDNua2QsT0dOVY9mRjhb5e5+tBW5Fg@mail.gmail.com>
Date:   Tue, 13 Aug 2019 20:01:10 -0700
From:   Vasily Khoruzhick <anarsoul@...il.com>
To:     Vasily Khoruzhick <anarsoul@...il.com>,
        Frank Lee <tiny.windzz@...il.com>,
        Mark Rutland <mark.rutland@....com>,
        devicetree <devicetree@...r.kernel.org>,
        Linux PM <linux-pm@...r.kernel.org>,
        Maxime Ripard <maxime.ripard@...tlin.com>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Daniel Lezcano <daniel.lezcano@...aro.org>,
        linux-kernel <linux-kernel@...r.kernel.org>,
        Eduardo Valentin <edubezval@...il.com>,
        Chen-Yu Tsai <wens@...e.org>, Rob Herring <robh+dt@...nel.org>,
        Jonathan.Cameron@...wei.com,
        Mauro Carvalho Chehab <mchehab+samsung@...nel.org>,
        rui.zhang@...el.com, "David S. Miller" <davem@...emloft.net>,
        arm-linux <linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH v5 08/18] thermal: sun8i: support mod clocks

On Tue, Aug 13, 2019 at 1:06 PM Ondřej Jirman <megous@...ous.com> wrote:
>
> On Mon, Aug 12, 2019 at 04:54:15PM -0700, Vasily Khoruzhick wrote:
> > On Mon, Aug 12, 2019 at 4:46 PM Frank Lee <tiny.windzz@...il.com> wrote:
> > >
> > > HI Vasily,
> > >
> > > On Sat, Aug 10, 2019 at 2:17 PM Vasily Khoruzhick <anarsoul@...il.com> wrote:
> > > >
> > > > On Fri, Aug 9, 2019 at 10:31 PM Yangtao Li <tiny.windzz@...il.com> wrote:
> > > > >
> > > > > H3 has extra clock, so introduce something in ths_thermal_chip/ths_device
> > > > > and adds the process of the clock.
> > > > >
> > > > > This is pre-work for supprt it.
> > > > >
> > > > > Signed-off-by: Yangtao Li <tiny.windzz@...il.com>
> > > > > ---
> > > > >  drivers/thermal/sun8i_thermal.c | 17 ++++++++++++++++-
> > > > >  1 file changed, 16 insertions(+), 1 deletion(-)
> > > > >
> > > > > diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
> > > > > index b934bc81eba7..6f4294c2aba7 100644
> > > > > --- a/drivers/thermal/sun8i_thermal.c
> > > > > +++ b/drivers/thermal/sun8i_thermal.c
> > > > > @@ -54,6 +54,7 @@ struct tsensor {
> > > > >  };
> > > > >
> > > > >  struct ths_thermal_chip {
> > > > > +       bool            has_mod_clk;
> > > > >         int             sensor_num;
> > > > >         int             offset;
> > > > >         int             scale;
> > > > > @@ -69,6 +70,7 @@ struct ths_device {
> > > > >         struct regmap                           *regmap;
> > > > >         struct reset_control                    *reset;
> > > > >         struct clk                              *bus_clk;
> > > > > +       struct clk                              *mod_clk;
> > > > >         struct tsensor                          sensor[MAX_SENSOR_NUM];
> > > > >  };
> > > > >
> > > > > @@ -274,6 +276,12 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
> > > > >         if (IS_ERR(tmdev->bus_clk))
> > > > >                 return PTR_ERR(tmdev->bus_clk);
> > > > >
> > > > > +       if (tmdev->chip->has_mod_clk) {
> > > > > +               tmdev->mod_clk = devm_clk_get(&pdev->dev, "mod");
> > > > > +               if (IS_ERR(tmdev->mod_clk))
> > > > > +                       return PTR_ERR(tmdev->mod_clk);
> > > > > +       }
> > > > > +
> > > > >         ret = reset_control_deassert(tmdev->reset);
> > > > >         if (ret)
> > > > >                 return ret;
> > > > > @@ -282,12 +290,18 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
> > > > >         if (ret)
> > > > >                 goto assert_reset;
> > > > >
> > > > > -       ret = sun50i_ths_calibrate(tmdev);
> > > > > +       ret = clk_prepare_enable(tmdev->mod_clk);
> > > >
> > > > You have to set rate of modclk before enabling it since you can't rely
> > > > on whatever bootloader left for you.
> > > >
> > > > Also I found that parameters you're using for PC_TEMP_PERIOD, ACQ0 and
> > > > ACQ1 are too aggressive and may result in high interrupt rate to the
> > > > point when it may stall RCU. I changed driver a bit to use params from
> > > > Philipp Rossak's work (modclk set to 4MHz, PC_TEMP_PERIOD is 7, ACQ0
> > > > is 255, ACQ1 is 63) and it fixed RCU stalls for me, see [1] for
> > > > details.
> > >
> > > Why is the RCU stall happening, is it caused by a deadlock?
> > > Can you provide log information and your configuration?
> > > I am a bit curious.
> >
> > It's not deadlock, I believe it just can't handle that many interrupts
> > when running at lowest CPU frequency. Even with Philipp's settings
> > there's ~20 interrupts a second from ths. I don't remember how many
> > interrupts were there with your settings.
> >
> > Unfortunately there's nothing interesting in backtraces, I'm using
> > Pine64-LTS board.
>
> Recently there was a similar issue, with buggy CCU driver that caused
> CIR interrupts being fired constantly, and it also resulted in RCU
> stalls. Looks like a comon cause of RCU stalls.
>
> THS timing settings probably need to be made specific to the SoC, because
> I noticed that the same settings lead to wildly different timings on
> different SoCs.
>
> It would be good to measure how often ths interrupt fires with this driver
> on various SoCs.
>
> 20 times a second and more sounds like overkill. I'd expect a useful
> range to be at most 5-10 times a second. That should be enough to stop
> overheating the SoC due to suddenly increased load, even without a
> heatsink.

Note that A64 has 3 sensors and each sensor has individual interrupt,
so technically it's 6-7 interrupts per sensor per second

> regards,
>         o.
>
> > > Thx,
> > > Yangtao
> > >
> > > >
> > > > [1] https://github.com/anarsoul/linux-2.6/commit/46b8bb0fe2ccd1cd88fa9181a2ecbf79e8d513b2
> > > >
> > > >
> > > > >         if (ret)
> > > > >                 goto bus_disable;
> > > > >
> > > > > +       ret = sun50i_ths_calibrate(tmdev);
> > > > > +       if (ret)
> > > > > +               goto mod_disable;
> > > > > +
> > > > >         return 0;
> > > > >
> > > > > +mod_disable:
> > > > > +       clk_disable_unprepare(tmdev->mod_clk);
> > > > >  bus_disable:
> > > > >         clk_disable_unprepare(tmdev->bus_clk);
> > > > >  assert_reset:
> > > > > @@ -395,6 +409,7 @@ static int sun8i_ths_remove(struct platform_device *pdev)
> > > > >  {
> > > > >         struct ths_device *tmdev = platform_get_drvdata(pdev);
> > > > >
> > > > > +       clk_disable_unprepare(tmdev->mod_clk);
> > > > >         clk_disable_unprepare(tmdev->bus_clk);
> > > > >         reset_control_assert(tmdev->reset);
> > > > >
> > > > > --
> > > > > 2.17.1
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > linux-arm-kernel mailing list
> > > > > linux-arm-kernel@...ts.infradead.org
> > > > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@...ts.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Powered by blists - more mailing lists