| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20190814120252.GA4572@toshiba>
Date: Wed, 14 Aug 2019 20:02:52 +0800
From: Alex Lu <alex_lu@...lsil.com.cn>
To: Marcel Holtmann <marcel@...tmann.org>
CC: Johan Hedberg <johan.hedberg@...il.com>,
<linux-bluetooth@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
Max Chou <max.chou@...ltek.com>
Subject: [PATCH v3] Bluetooth: btusb: Fix suspend issue for Realtek devices
From: Alex Lu <alex_lu@...lsil.com.cn>
>From the perspective of controller, global suspend means there is no
SET_FEATURE (DEVICE_REMOTE_WAKEUP) and controller would drop the
firmware. It would consume less power. So we should not send this kind
of SET_FEATURE when host goes to suspend state.
Otherwise, when making device enter selective suspend, host should send
SET_FEATURE to make sure the firmware remains.
Signed-off-by: Alex Lu <alex_lu@...lsil.com.cn>
---
Changes in v3:
- Change to fit for bluetooth-next
Changes in v2:
- Change flag to be more descriptive
- Delete pointless #ifdef CONFIG_BT_HCIBTUSB_RTL and #endif
drivers/bluetooth/btusb.c | 34 ++++++++++++++++++++++++++++++----
1 file changed, 30 insertions(+), 4 deletions(-)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 3876fee6ad13..b606c663ba57 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -435,6 +435,7 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
#define BTUSB_OOB_WAKE_ENABLED 11
#define BTUSB_HW_RESET_ACTIVE 12
#define BTUSB_TX_WAIT_VND_EVT 13
+#define BTUSB_WAKEUP_DISABLE 14
struct btusb_data {
struct hci_dev *hdev;
@@ -1175,6 +1176,13 @@ static int btusb_open(struct hci_dev *hdev)
*/
device_wakeup_enable(&data->udev->dev);
+ /* Disable device remote wakeup when host is suspended
+ * For Realtek chips, global suspend without
+ * SET_FEATURE (DEVICE_REMOTE_WAKEUP) can save more power in device.
+ */
+ if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+ device_wakeup_disable(&data->udev->dev);
+
if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags))
goto done;
@@ -1238,6 +1246,11 @@ static int btusb_close(struct hci_dev *hdev)
goto failed;
data->intf->needs_remote_wakeup = 0;
+
+ /* Enable remote wake up for auto-suspend */
+ if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+ data->intf->needs_remote_wakeup = 1;
+
device_wakeup_disable(&data->udev->dev);
usb_autopm_put_interface(data->intf);
@@ -3769,11 +3782,11 @@ static int btusb_probe(struct usb_interface *intf,
hdev->setup = btrtl_setup_realtek;
hdev->shutdown = btrtl_shutdown_realtek;
- /* Realtek devices lose their updated firmware over suspend,
- * but the USB hub doesn't notice any status change.
- * Explicitly request a device reset on resume.
+ /* Realtek devices lose their updated firmware over global
+ * suspend that means host doesn't send SET_FEATURE
+ * (DEVICE_REMOTE_WAKEUP)
*/
- interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
+ set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
}
#endif
@@ -3947,6 +3960,19 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
enable_irq(data->oob_wake_irq);
}
+ /* For global suspend, Realtek devices lose the loaded fw
+ * in them. But for autosuspend, firmware should remain.
+ * Actually, it depends on whether the usb host sends
+ * set feature (enable wakeup) or not.
+ */
+ if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags)) {
+ if (PMSG_IS_AUTO(message) &&
+ device_can_wakeup(&data->udev->dev))
+ data->udev->do_remote_wakeup = 1;
+ else if (!PMSG_IS_AUTO(message))
+ data->udev->reset_resume = 1;
+ }
+
return 0;
}
--
2.19.2
Powered by blists - more mailing lists