linux-kernel - Re: [PATCH 14/22] ARM: omap1: use pci_ioremap_io() for omap

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20190828182318.GL30291@darkstar.musicnaut.iki.fi>
Date:   Wed, 28 Aug 2019 21:23:19 +0300
From:   Aaro Koskinen <aaro.koskinen@....fi>
To:     Arnd Bergmann <arnd@...db.de>
Cc:     Tony Lindgren <tony@...mide.com>,
        Dominik Brodowski <linux@...inikbrodowski.net>,
        linux-omap <linux-omap@...r.kernel.org>,
        Linux ARM <linux-arm-kernel@...ts.infradead.org>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Linus Walleij <linus.walleij@...aro.org>,
        Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>,
        Tomi Valkeinen <tomi.valkeinen@...com>,
        Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 14/22] ARM: omap1: use pci_ioremap_io() for omap_cf

Hi,

On Wed, Aug 28, 2019 at 03:02:36PM +0200, Arnd Bergmann wrote:
> On Tue, Aug 27, 2019 at 9:05 PM Aaro Koskinen <aaro.koskinen@....fi> wrote:
> > On Tue, Aug 27, 2019 at 06:33:01PM +0200, Arnd Bergmann wrote:
> > > On Fri, Aug 16, 2019 at 10:34 AM Aaro Koskinen <aaro.koskinen@....fi> wrote:
> > > > However with earlyprintk it seems to hang as soon as kernel tries to print
> > > > something. So something goes wrong with early DEBUG_LL mapping code when
> > > > CONFIG_DEBUG_UART_VIRT=0xff000000 is used?
> > >
> > > I just redid the calculation and came out with the same address, so I
> > > don't think I put the wrong one there. The address also does not
> > > conflict with the PCI mapping, and the address is the same one that
> > > is installed later, so that should also be fine.
> > >
> > > Are you sure you used the correct address in the .config file? If you
> > > ran 'make oldconfig', the virtual address would not be changed here
> > > as I just modify the default for a fresh 'make omap1_defconfig'
> > > run or similar.
> >
> > Yes... You should be able to try this out also in QEMU to see the hang:
> 
> Haven't tried yet, but I took a look at the dump:
> 
> > $ qemu-system-arm -M sx1 -kernel sx1-zImage -nographic
> >
> > [ Hangs silently, press Ctrl-a c to enter monitor. ]
> >
> > QEMU 4.1.0 monitor - type 'help' for more information
> > (qemu) info registers
> > R00=c0379de1 R01=0000005b R02=00000000 R03=ff000000
> > R04=00000000 R05=00000031 R06=c038f119 R07=00000000
> > R08=00000000 R09=c038f50e R10=600001d3 R11=00000001
> > R12=00000010 R13=c0379de0 R14=c000e07c R15=c000dfcc
> > PSR=000001d3 ---- A svc32
> > FPSCR: 00000000
> >
> > from System.map:
> > c000df7c T printascii
> > c000dfe0 T printch
> 
> Ok, that is clearly the "busyloop" macro in
> arch/arm/include/debug/8250.S, checking if the data got sent.
> 
> The 'r2' register contains zero, so UART_LSR_TEMT and
> UART_LSR_THRE are not set, but presumably the mapping
> was installed right since you did not get a page fault.
> 
> I assume you checked that the uart output wasn't already broken
> by one of the earlier patches, right?

Correct, it's only with the mapping change patch it hangs.

> Also, looking at arch/arm/mach-omap1/include/mach/uncompress.h
> it seems that SX1 normally uses UART3, not UART1.
> Is that different in qemu?

In QEMU all uarts can be used, trying with UART3 as early console
hangs as well. (It prints Uncompressing... done. but I guess that's
done with the physical address.)

A.