| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20190829075405.j7av4aojvzddlfz3@pengutronix.de>
Date: Thu, 29 Aug 2019 09:54:05 +0200
From: Marco Felsch <m.felsch@...gutronix.de>
To: Oliver Graute <oliver.graute@...il.com>
Cc: shawnguo@...nel.org, Mark Rutland <mark.rutland@....com>,
devicetree@...r.kernel.org, narmstrong@...libre.com,
Sascha Hauer <s.hauer@...gutronix.de>,
linux-kernel@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
NXP Linux Team <linux-imx@....com>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCHv5 2/2] ARM: dts: Add support for i.MX6 UltraLite DART
Variscite Customboard
Hi Oliver,
On 19-08-28 18:19, Oliver Graute wrote:
> This patch adds DeviceTree Source for the i.MX6 UltraLite DART NAND/WIFI
>
> Signed-off-by: Oliver Graute <oliver.graute@...il.com>
> Cc: Shawn Guo <shawnguo@...nel.org>
> Cc: Neil Armstrong <narmstrong@...libre.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6ul-var-6ulcustomboard.dts | 196 ++++++++++++++++++++++++
> 2 files changed, 197 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6ul-var-6ulcustomboard.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a24a6a1..a2a69e4 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -579,6 +579,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
> imx6ul-tx6ul-0010.dtb \
> imx6ul-tx6ul-0011.dtb \
> imx6ul-tx6ul-mainboard.dtb \
> + imx6ul-var-6ulcustomboard.dtb \
> imx6ull-14x14-evk.dtb \
> imx6ull-colibri-eval-v3.dtb \
> imx6ull-colibri-wifi-eval-v3.dtb \
> diff --git a/arch/arm/boot/dts/imx6ul-var-6ulcustomboard.dts b/arch/arm/boot/dts/imx6ul-var-6ulcustomboard.dts
> new file mode 100644
> index 00000000..1861b34
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-var-6ulcustomboard.dts
> @@ -0,0 +1,196 @@
> +// SPDX-License-Identifier: (GPL-2.0)
> +/*
> + * Support for Variscite DART-6UL Module
> + *
> + * Copyright (C) 2015 Freescale Semiconductor, Inc.
> + * Copyright (C) 2015-2016 Variscite Ltd. - http://www.variscite.com
> + * Copyright (C) 2018-2019 Oliver Graute <oliver.graute@...il.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/input/input.h>
> +#include "imx6ul-imx6ull-var-dart-common.dtsi"
> +
> +/ {
> + model = "Variscite i.MX6 UltraLite Carrier-board";
> + compatible = "variscite,6ulcustomboard", "fsl,imx6ul";
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 20000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + status = "okay";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + user {
> + gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
Please mux the gpios where you need them. In this case mux it within the
gpio-keys node.
> + linux,code = <KEY_BACK>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + d16-led {
> + gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>;
The same applies here.
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "wm8731audio";
> + simple-audio-card,widgets =
> + "Headphone", "Headphone Jack",
> + "Line", "Line Jack",
> + "Microphone", "Mic Jack";
> + simple-audio-card,routing =
> + "Headphone Jack", "RHPOUT",
> + "Headphone Jack", "LHPOUT",
> + "LLINEIN", "Line Jack",
> + "RLINEIN", "Line Jack",
> + "MICIN", "Mic Bias",
> + "Mic Bias", "Mic Jack";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,bitclock-master = <&sound_master>;
> + simple-audio-card,frame-master = <&sound_master>;
> +
> + sound_master: simple-audio-card,cpu {
> + sound-dai = <&sai2>;
> + };
Where is the codec node?
> + };
> +};
> +
> +&can1 {
> + status = "okay";
We need to move the complete muxing from the SoM dtsi to the baseboard
for all baseboard related nodes.. I tought that the Dart 6UL layout
follows a specific standard but that isn't the case.
> +};
> +
> +&can2 {
> + status = "okay";
> +};
> +
> +&fec1 {
> + phy-mode = "rgmii";
This avoid such re-assigning here too. Also the imx6ul only support
10/100 Mbit/s. So rgmii makes no sense here.
> + phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
> + phy-handle = <ðphy0>;
> + status = "okay";
> +};
> +
> +&fec2 {
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
> + phy-handle = <ðphy1>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock_frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + wm8731: audio-codec@1a {
> + #sound-dai-cells = <0>;
Please move #sound-dai-cells below compatible and reg property.
> + compatible = "wlf,wm8731";
> + reg = <0x1a>;
> + clocks = <&clks IMX6UL_CLK_SAI2>;
> + clock-names = "mclk";
> + };
> +
> + touchscreen@38 {
> + compatible = "edt,edt-ft5x06";
> + reg = <0x38>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <4 0>;
Make use of IRQ_TYPE_*
> + touchscreen-size-x = <800>;
> + touchscreen-size-y = <480>;
> + touchscreen-inverted-x;
> + touchscreen-inverted-y;
> + wakeup-source;
> + };
> +
> + rtc@68 {
> + compatible = "dallas,ds1337";
> + reg = <0x68>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rtc>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> + };
> +};
> +
> +&lcdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcdif>;
> + display = <&display0>;
> + status = "okay";
> +
> + display0: display0 {
> + bits-per-pixel = <16>;
> + bus-width = <24>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency =<35000000>;
> + hactive = <800>;
> + vactive = <480>;
> + hfront-porch = <40>;
> + hback-porch = <40>;
> + hsync-len = <48>;
> + vback-porch = <29>;
> + vfront-porch = <13>;
> + vsync-len = <3>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_rtc: rtcgrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0
> + >;
> + };
As I said above, move the complete muxing pwm/usb/i2c/lcd/... from the
som dtsi to the baseboard dts because it is only valid for this
baseboard. Another baseboard using this som can have a complete
different mux option.
Regards,
Marco
> +};
> --
> 2.7.4
>
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Powered by blists - more mailing lists