linux-kernel - [PATCH v5 2/9] dt-bindings: i2c: add bindings for i2c analog and digital filter

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1568189911-31641-3-git-send-email-eugen.hristev@microchip.com>
Date:   Wed, 11 Sep 2019 08:24:20 +0000
From:   <Eugen.Hristev@...rochip.com>
To:     <wsa@...-dreams.de>, <peda@...ntia.se>, <mark.rutland@....com>,
        <Ludovic.Desroches@...rochip.com>, <linux-i2c@...r.kernel.org>,
        <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-kernel@...r.kernel.org>, <alexandre.belloni@...tlin.com>,
        <robh+dt@...nel.org>
CC:     <Eugen.Hristev@...rochip.com>, <Nicolas.Ferre@...rochip.com>
Subject: [PATCH v5 2/9] dt-bindings: i2c: add bindings for i2c analog and
 digital filter

From: Eugen Hristev <eugen.hristev@...rochip.com>

Some i2c controllers have a built-in digital or analog filter.
This is specifically required depending on the hardware PCB/board.
Some controllers also allow specifying the maximum width of the
spikes that can be filtered for digital filter. The width length can be
specified in nanoseconds.
Analog filters can be configured to have a cutoff frequency (low-pass filter).
This frequency can be specified in Hz.
Added an optional property for such types of analog filters.

Signed-off-by: Eugen Hristev <eugen.hristev@...rochip.com>
---
 Documentation/devicetree/bindings/i2c/i2c.txt | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt
index 44efafd..9a53df4 100644
--- a/Documentation/devicetree/bindings/i2c/i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c.txt
@@ -55,6 +55,24 @@ wants to support one of the below features, it should adapt the bindings below.
 	Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C
 	specification.
 
+- i2c-analog-filter
+	Enable analog filter for i2c lines.
+
+- i2c-digital-filter
+	Enable digital filter for i2c lines.
+
+- i2c-digital-filter-width-ns
+	Width of spikes which can be filtered by digital filter
+	(i2c-digital-filter). This width is specified in nanoseconds.
+
+- i2c-analog-filter-cutoff-frequency
+	Frequency that the analog filter (i2c-analog-filter) uses to distinguish
+	which signal to filter. Signal with higher frequency than specified will
+	be filtered out. Only lower frequency will pass (this is applicable to
+	a low-pass analog filter). Typical value should be above the normal
+	i2c bus clock frequency (clock-frequency).
+	Specified in Hz.
+
 - interrupts
 	interrupts used by the device.
 
-- 
2.7.4