| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20190917163427.GA1475935@arch-dsk-01>
Date: Tue, 17 Sep 2019 19:34:27 +0300
From: tinywrkb <tinywrkb@...il.com>
To: Russell King - ARM Linux admin <linux@...linux.org.uk>
Cc: Mark Rutland <mark.rutland@....com>, Andrew Lunn <andrew@...n.ch>,
Baruch Siach <baruch@...s.co.il>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@...r.kernel.org>, Shawn Guo <shawnguo@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
open list <linux-kernel@...r.kernel.org>,
Rob Herring <robh+dt@...nel.org>,
NXP Linux Team <linux-imx@....com>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH] ARM: dts: imx6dl: SolidRun: add phy node with 100Mb/s
max-speed
On Tue, Sep 17, 2019 at 04:30:27PM +0100, Russell King - ARM Linux admin wrote:
> On Tue, Sep 17, 2019 at 04:17:07PM +0100, Russell King - ARM Linux admin wrote:
> > On Tue, Sep 17, 2019 at 02:39:43PM +0100, Russell King - ARM Linux admin wrote:
> > > On Tue, Sep 17, 2019 at 04:32:53PM +0300, tinywrkb wrote:
> > > > On Tue, Sep 17, 2019 at 02:54:34PM +0200, Andrew Lunn wrote:
> > > > > On Tue, Sep 17, 2019 at 03:41:01PM +0300, tinywrkb wrote:
> > > > > > On Sun, Sep 15, 2019 at 03:56:52PM +0200, Andrew Lunn wrote:
> > > > > > > > Tinywrkb confirmed to me in private communication that revert of
> > > > > > > > 5502b218e001 fixes Ethernet for him on effected system.
> > > > > > > >
> > > > > > > > He also referred me to an old Cubox-i spec that lists 10/100 Ethernet
> > > > > > > > only for i.MX6 Solo/DualLite variants of Cubox-i. It turns out that
> > > > > > > > there was a plan to use a different 10/100 PHY for Solo/DualLite
> > > > > > > > SOMs. This plan never materialized. All SolidRun i.MX6 SOMs use the same
> > > > > > > > AR8035 PHY that supports 1Gb.
> > > > > > > >
> > > > > > > > Commit 5502b218e001 might be triggering a hardware issue on the affected
> > > > > > > > Cubox-i. I could not reproduce the issue here with Cubox-i and a Dual
> > > > > > > > SOM variant running v5.3-rc8. I have no Solo/DualLite variant handy at
> > > > > > > > the moment.
> > > > > > >
> > > > > > > Could somebody with an affected device show us the output of ethtool
> > > > > > > with and without 5502b218e001. Does one show 1G has been negotiated,
> > > > > > > and the other 100Mbps? If this is true, how does it get 100Mbps
> > > > > > > without that patch? We are missing a piece of the puzzle.
> > > > > > >
> > > > > > > Andrew
> > > > > >
> > > > > > linux-test-5.1rc1-a2703de70942-without_bad_commit
> > > > > >
> > > > > > Settings for eth0:
> > > > > > Supported ports: [ TP MII ]
> > > > > > Supported link modes: 10baseT/Half 10baseT/Full
> > > > > > 100baseT/Half 100baseT/Full
> > > > > > 1000baseT/Full
> > > > >
> > > > > So this means the local device says it can do 1000Mbps.
> > > > >
> > > > >
> > > > > > Supported pause frame use: Symmetric
> > > > > > Supports auto-negotiation: Yes
> > > > > > Supported FEC modes: Not reported
> > > > > > Advertised link modes: 10baseT/Half 10baseT/Full
> > > > > > 100baseT/Half 100baseT/Full
> > > > > > 1000baseT/Full
> > > > >
> > > > > The link peer can also do 1000Mbps.
> > > > >
> > > > >
> > > > > > Advertised pause frame use: Symmetric
> > > > > > Advertised auto-negotiation: Yes
> > > > > > Advertised FEC modes: Not reported
> > > > > > Link partner advertised link modes: 10baseT/Half 10baseT/Full
> > > > > > 100baseT/Half 100baseT/Full
> > > > > > 1000baseT/Full
> > > > > > Link partner advertised pause frame use: Symmetric
> > > > > > Link partner advertised auto-negotiation: Yes
> > > > > > Link partner advertised FEC modes: Not reported
> > > > > > Speed: 100Mb/s
> > > > >
> > > > > Yet they have decided to do 100Mbps.
> > > > >
> > > > > We need to understand Why? The generic PHY driver would not do this on
> > > > > its own. So i'm thinking something has poked a PHY register with some
> > > > > value, and this patch is causing it to be over written.
> > > > >
> > > > > Please can you use mii-tool -v -v to dump the PHY registers in each
> > > > > case.
> > > > >
> > > > > Thanks
> > > > > Andrew
> > > >
> > > > Here's the output of # mii-tool -v -v eth0
> > > >
> > > > * linux-test-5.1rc1-a2703de70942-without_bad_commit
> > > >
> > > > Using SIOCGMIIPHY=0x8947
> > > > eth0: negotiated 100baseTx-FD flow-control, link ok
> > > > registers for MII PHY 0:
> > > > 3100 796d 004d d072 15e1 c5e1 000f 0000
> > > > 0000 0000 0800 0000 0000 0000 0000 a000
> > > > 0000 0000 0000 f420 082c 0000 04e8 0000
> > > > 3200 3000 0000 063d 0000 0000 0000 0000
> > > > product info: vendor 00:13:74, model 7 rev 2
> > > > basic mode: autonegotiation enabled
> > > > basic status: autonegotiation complete, link ok
> > > > capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
> > > > advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
> > > > link partner: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
> > >
> > > This is *not* advertising 1000baseT modes (register 9).
> > >
> > > >
> > > >
> > > > * linux-test-5.1rc1-5502b218e001-with_bad_commit
> > > >
> > > > Using SIOCGMIIPHY=0x8947
> > > > eth0: negotiated 100baseTx-FD flow-control, link ok
> > > > registers for MII PHY 0:
> > > > 3100 796d 004d d072 15e1 c5e1 000d 0000
> > > > 0000 0000 0800 0000 0000 0000 0000 a000
> > > > 0000 0000 0000 0000 082c 0000 04e8 0000
> > > > 3200 3000 0000 063d 0000 0000 0000 0000
> > > > product info: vendor 00:13:74, model 7 rev 2
> > > > basic mode: autonegotiation enabled
> > > > basic status: autonegotiation complete, link ok
> > > > capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
> > > > advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
> > > > link partner: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
> > >
> > > Neither is this.
> > >
> > > However, the kernel and phylib _thinks_ that it is. My guess is
> > > something has rewritten the PHY registers from userspace, rather
> > > than using ethtool to change the advertisment. The MAC is still
> > > trying to operate at 1000Mbps (since that is what phylib resolved)
> > > yet the link might be actually operating at 100Mbps - but for that
> > > to happen, we should've seen the link go down and up again.
> > >
> > > Odd.
> >
> > For reference, here I see:
> >
> > Using SIOCGMIIPHY=0x8947
> > eth0: negotiated 1000baseT-FD flow-control, link ok
> > registers for MII PHY 0:
> > 3100 796d 004d d072 15e1 c1e1 000d 0000
> > 0000 0200 3800 0000 0000 0000 0000 a000
> > 0000 0000 0000 0000 082c 0000 04e8 0000
> > 3200 3000 0000 060e 0000 0000 0000 0000
> > product info: vendor 00:13:74, model 7 rev 2
> > basic mode: autonegotiation enabled
> > basic status: autonegotiation complete, link ok
> > capabilities: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
> > advertising: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
> > link partner: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
> >
> > Note that userspace writing to register 9 (1G settings) will update
> > the physical PHY's advertisment for 1G speeds, but the kernel's idea
> > will not be updated, so things will become de-sync'd, and the kernel
> > _will_ incorrectly determine the speed.
> >
> > So, are you using mii-tool or mii-diag to change the negotiation
> > settings, rather than using ethtool?
> >
> > This is likely the case, as prior to 5502b218e001, we used to read
> > the advertisment registers afresh each time we evaluate the resulting
> > link mode. After 5502b218e001, we use the advertisment mask cached
> > in phydev->advertising, which, looking at phy_mii_ioctl(), will not
> > be updated if register 9 is written.
>
> Please try this patch - I haven't written a commit message for it yet,
> it's just to prove the above point.
>
> Thanks.
>
> drivers/net/phy/phy.c | 5 +++++
> include/linux/mii.h | 9 +++++++++
> 2 files changed, 14 insertions(+)
>
> diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> index 7af390d8bbdb..068a08a50064 100644
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c
> @@ -458,6 +458,11 @@ int phy_mii_ioctl(struct phy_device *phydev, struct ifreq *ifr, int cmd)
> val);
> change_autoneg = true;
> break;
> + case MII_CTRL1000:
> + mii_ctrl1000_mod_linkmode_adv_t(phydev->advertising,
> + val);
> + change_autoneg = true;
> + break;
> default:
> /* do nothing */
> break;
> diff --git a/include/linux/mii.h b/include/linux/mii.h
> index 5cd824c1c0ca..1249d32dbd63 100644
> --- a/include/linux/mii.h
> +++ b/include/linux/mii.h
> @@ -455,6 +455,15 @@ static inline void mii_lpa_mod_linkmode_lpa_t(unsigned long *lp_advertising,
> lp_advertising, lpa & LPA_LPACK);
> }
>
> +static inline void mii_ctrl1000_mod_linkmode_adv_t(unsigned long *advertising,
> + u32 ctrl1000)
> +{
> + linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, advertising,
> + ctrl1000 & ADVERTISE_1000HALF);
> + linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, advertising,
> + ctrl1000 & ADVERTISE_1000FULL);
> +}
> +
> /**
> * linkmode_adv_to_lcl_adv_t
> * @advertising:pointer to linkmode advertising
>
> --
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
> According to speedtest.net: 11.9Mbps down 500kbps up
The patch didn't fix the issue.
# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: yes
# mii-tool -v -v eth0
Using SIOCGMIIPHY=0x8947
eth0: negotiated 100baseTx-FD flow-control, link ok
registers for MII PHY 0:
3100 796d 004d d072 15e1 c5e1 000f 0000
0000 0000 0800 0000 0000 0000 0000 a000
0000 0000 0000 f420 082c 0000 04e8 0000
3200 3000 0000 063d 0000 0000 0000 0000
product info: vendor 00:13:74, model 7 rev 2
basic mode: autonegotiation enabled
basic status: autonegotiation complete, link ok
capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
link partner: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
# journalctl -b | egrep -i 'phy|eth|fec'|grep -v usb
kernel: Booting Linux on physical CPU 0x0
kernel: libphy: Fixed MDIO Bus: probed
kernel: libphy: fec_enet_mii_bus: probed
kernel: fec 2188000.ethernet eth0: registered PHC device 0
kernel: dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.31a with HDCP (DWC HDMI 3D TX PHY)
kernel: Generic PHY 2188000.ethernet-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
kernel: fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
systemd-networkd[242]: eth0: Gained carrier
Powered by blists - more mailing lists