linux-kernel - Re: [PATCH] serial: sprd: Add polling IO support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Message-ID: <CAHshu7PoJriq6R+rNzqAVrEy=mSWvu6k=83=pkRo0dNhrS1xhw@mail.gmail.com>
Date:   Thu, 19 Sep 2019 10:14:31 +0800
From:   hhome liu <liuhhome@...il.com>
To:     Baolin Wang <baolin.wang@...aro.org>
Cc:     Greg KH <gregkh@...uxfoundation.org>, Jiri Slaby <jslaby@...e.com>,
        刘岚清 (Lanqing Liu) 
        <lanqing.liu@...soc.com>, linux-serial@...r.kernel.org,
        LKML <linux-kernel@...r.kernel.org>,
        Orson Zhai <orsonzhai@...il.com>,
        Chunyan Zhang <zhang.lyra@...il.com>
Subject: Re: [PATCH] serial: sprd: Add polling IO support

Baolin Wang <baolin.wang@...aro.org> 于2019年9月18日周三 下午8:10写道：
>
> Hi Lanqing,
>
> On Wed, 18 Sep 2019 at 16:16, Lanqing Liu <liuhhome@...il.com> wrote:
> >
> > In order to access the UART without the interrupts, the kernel uses
> > the basic polling methods for IO with the device. With these methods
> > implemented, it is now possible to enable kgdb during early boot over serial.
> >
> > Signed-off-by: Lanqing Liu <liuhhome@...il.com>
> > ---
> >  drivers/tty/serial/sprd_serial.c | 22 ++++++++++++++++++++++
> >  1 file changed, 22 insertions(+)
> >
> > diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
> > index 73d71a4..579ab41 100644
> > --- a/drivers/tty/serial/sprd_serial.c
> > +++ b/drivers/tty/serial/sprd_serial.c
> > @@ -911,6 +911,24 @@ static void sprd_pm(struct uart_port *port, unsigned int state,
> >         }
> >  }
> >
> > +#ifdef CONFIG_CONSOLE_POLL
> > +static int sprd_poll_get_char(struct uart_port *port)
> > +{
> > +       while (!(serial_in(port, SPRD_STS1) & SPRD_RX_FIFO_CNT_MASK))
> > +               cpu_relax();
> > +
> > +       return serial_in(port, SPRD_RXD);
> > +}
> > +
> > +static void sprd_poll_put_char(struct uart_port *port, unsigned char ch)
> > +{
> > +       while (serial_in(port, SPRD_STS1) & SPRD_TX_FIFO_CNT_MASK)
> > +               cpu_relax();
> > +
> > +       serial_out(port, SPRD_TXD, ch);
> > +}
> > +#endif
>
> When I tested your patch, I found only one case can work if the port
> used by KGDB is same with the port selected as console, which means
> this port will be powered on all the time. We had implemented the
> power management for the UART ports, so I think you should enable the
> clock for the port used by KGDB in poll_init(), then other ports can
> be used by KGDB.
>
Yes, agree with you. I will add poll_init()  support.  Thanks for your
comments.
> > +
> >  static const struct uart_ops serial_sprd_ops = {
> >         .tx_empty = sprd_tx_empty,
> >         .get_mctrl = sprd_get_mctrl,
> > @@ -928,6 +946,10 @@ static void sprd_pm(struct uart_port *port, unsigned int state,
> >         .config_port = sprd_config_port,
> >         .verify_port = sprd_verify_port,
> >         .pm = sprd_pm,
> > +#ifdef CONFIG_CONSOLE_POLL
> > +       .poll_get_char  = sprd_poll_get_char,
> > +       .poll_put_char  = sprd_poll_put_char,
> > +#endif
> >  };
> >
> >  #ifdef CONFIG_SERIAL_SPRD_CONSOLE
> > --
> > 1.9.1
> >
>
>
> --
> Baolin Wang
> Best Regards