| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1jk19t28zs.fsf@starbuckisacylon.baylibre.com>
Date: Fri, 27 Sep 2019 14:56:23 +0200
From: Jerome Brunet <jbrunet@...libre.com>
To: Jian Hu <jian.hu@...ogic.com>
Cc: Stephen Boyd <sboyd@...nel.org>,
Jerome Brunet <jbrunet@...libre.com>,
Neil Armstrong <narmstrong@...libre.com>,
Rob Herring <robh@...nel.org>,
Jianxin Pan <jianxin.pan@...ogic.com>,
devicetree@...r.kernel.org,
Martin Blumenstingl <martin.blumenstingl@...glemail.com>,
Kevin Hilman <khilman@...libre.com>,
Michael Turquette <mturquette@...libre.com>,
linux-kernel@...r.kernel.org,
Qiufang Dai <qiufang.dai@...ogic.com>,
linux-amlogic@...ts.infradead.org, linux-clk@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 2/2] clk: meson: a1: add support for Amlogic A1 clock driver
On Fri 27 Sep 2019 at 05:11, Jian Hu <jian.hu@...ogic.com> wrote:
> Hi, Stephen
>
> Thank you for review
>
> On 2019/9/25 21:12, Stephen Boyd wrote:
>> Quoting Jian Hu (2019-09-25 04:44:48)
>>> The Amlogic A1 clock includes three parts:
>>> peripheral clocks, pll clocks, CPU clocks.
>>> sys pll and CPU clocks will be sent in next patch.
>>>
>>> Unlike the previous series, there is no EE/AO domain
>>> in A1 CLK controllers.
>>>
>>> Signed-off-by: Jian Hu <jian.hu@...ogic.com>
>>> Signed-off-by: Jianxin Pan <jianxin.pan@...ogic.com>
>>
>> This second name didn't send the patch. Please follow the signoff
>> procedures documented in Documentation/process/submitting-patches.rst
>>
>>> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
>>> index 16d7614..a48f67d 100644
>>> --- a/arch/arm64/Kconfig.platforms
>>> +++ b/arch/arm64/Kconfig.platforms
>>> @@ -138,6 +138,7 @@ config ARCH_MESON
>>> select COMMON_CLK_AXG
>>> select COMMON_CLK_G12A
>>> select MESON_IRQ_GPIO
>>> + select COMMON_CLK_A1
>>
>> Sort?
> ok, I will put it behind COMMON_CLK_AXG
>>
>>> help
>>> This enables support for the arm64 based Amlogic SoCs
>>> such as the s905, S905X/D, S912, A113X/D or S905X/D2
>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>> index dabeb43..e6cb4c3 100644
>>> --- a/drivers/clk/meson/Kconfig
>>> +++ b/drivers/clk/meson/Kconfig
>>> @@ -107,3 +107,13 @@ config COMMON_CLK_G12A
>>> help
>>> Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>>> devices, aka g12a. Say Y if you want peripherals to work.
>>> +
>>> +config COMMON_CLK_A1
>>
>> Probably should be placed somewhere alphabetically in this file?
> ok, I will put it behind COMMON_CLK_AXG_AUDIO
>>
>>> + bool
>>> + depends on ARCH_MESON
>>> + select COMMON_CLK_MESON_REGMAP
>>> + select COMMON_CLK_MESON_DUALDIV
>>> + select COMMON_CLK_MESON_PLL
>>> + help
>>> + Support for the clock controller on Amlogic A113L device,
>>> + aka a1. Say Y if you want peripherals to work.
>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>> index 3939f21..6be3a8f 100644
>>> --- a/drivers/clk/meson/Makefile
>>> +++ b/drivers/clk/meson/Makefile
>>> @@ -19,3 +19,4 @@ obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>>> obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>>> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>>> +obj-$(CONFIG_COMMON_CLK_A1) += a1.o
>>
>> I would guess this should be sorted on Kconfig name in this file?
> ok, I will put it behind COMMON_CLK_AXG_AUDIO
>>
>>> diff --git a/drivers/clk/meson/a1.c b/drivers/clk/meson/a1.c
>>> new file mode 100644
>>> index 0000000..26edae0f
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1.c
>>> @@ -0,0 +1,2617 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +/*
>>> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
>>> + */
>>> +
>>> +#include <linux/clk-provider.h>
>>> +#include <linux/init.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/of_address.h>
>>> +#include "clk-mpll.h"
>>> +#include "clk-pll.h"
>>> +#include "clk-regmap.h"
>>> +#include "vid-pll-div.h"
>>> +#include "clk-dualdiv.h"
>>> +#include "meson-eeclk.h"
>>> +#include "a1.h"
>>> +
>> [...]
>>> +
>>> +/*
>>> + * The Meson A1 HIFI PLL is 614.4M, it requires
>>> + * a strict register sequence to enable the PLL.
>>> + * set meson_clk_pcie_pll_ops as its ops
>>
>> Please remove this last line as it's obvious from the code what ops are
>> used.
>>
> ok, I will remove it.
>>> + */
>>> +static struct clk_regmap a1_hifi_pll = {
>>> + .data = &(struct meson_clk_pll_data){
>>> + .en = {
>>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>>> + .shift = 28,
>>> + .width = 1,
>>> + },
>>> + .m = {
>>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>>> + .shift = 0,
>>> + .width = 8,
>>> + },
>>> + .n = {
>>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>>> + .shift = 10,
>>> + .width = 5,
>>> + },
>>> + .frac = {
>>> + .reg_off = ANACTRL_HIFIPLL_CTRL1,
>>> + .shift = 0,
>>> + .width = 19,
>>> + },
>>> + .l = {
>>> + .reg_off = ANACTRL_HIFIPLL_STS,
>>> + .shift = 31,
>>> + .width = 1,
>>> + },
>>> + .table = a1_hifi_pll_params_table,
>>> + .init_regs = a1_hifi_init_regs,
>>> + .init_count = ARRAY_SIZE(a1_hifi_init_regs),
>>> + },
>>> + .hw.init = &(struct clk_init_data){
>>> + .name = "hifi_pll",
>>> + .ops = &meson_clk_pcie_pll_ops,
>>> + .parent_hws = (const struct clk_hw *[]) {
>>> + &a1_xtal_hifipll.hw
>>> + },
>>> + .num_parents = 1,
>>> + },
>>> +};
>>> +
>> [..]
>>> +
>>> +static struct clk_regmap a1_fclk_div2 = {
>>> + .data = &(struct clk_regmap_gate_data){
>>> + .offset = ANACTRL_FIXPLL_CTRL0,
>>> + .bit_idx = 21,
>>> + },
>>> + .hw.init = &(struct clk_init_data){
>>> + .name = "fclk_div2",
>>> + .ops = &clk_regmap_gate_ops,
>>> + .parent_hws = (const struct clk_hw *[]) {
>>> + &a1_fclk_div2_div.hw
>>> + },
>>> + .num_parents = 1,
>>> + /*
>>> + * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
>>> + * or its children clocks.
>>
>> This comment is useless. Please replace it with an actual reason for
>> keeping the clk on instead of describing what the flag does.
>>
> ok, The actual reason is it should not change at runtime.
Yeah, from the flag we understand that you want to keep this on. What we
are after is why ? What device is using this clock and cannot tolerate
this gate to turn off ?
This is important and this is kind of comment we are after.
These flag should be viewed as "mid term work around". In the end, there
should be a driver for your device which claims the clock and properly
manage it
>>> + */
>>> + .flags = CLK_IS_CRITICAL,
>>> + },
>>> +};
>>> +
>> [..]
>>> +static struct clk_regmap a1_dmc = {
>>> + .data = &(struct clk_regmap_gate_data){
>>> + .offset = DMC_CLK_CTRL,
>>> + .bit_idx = 8,
>>> + },
>>> + .hw.init = &(struct clk_init_data) {
>>> + .name = "dmc",
>>> + .ops = &clk_regmap_gate_ops,
>>> + .parent_hws = (const struct clk_hw *[]) {
>>> + &a1_dmc_sel2.hw
>>> + },
>>> + .num_parents = 1,
>>> + /*
>>> + * add CLK_IGNORE_UNUSED to avoid hangup
>>> + * DDR clock should not change at runtime
>>> + */
>>> + .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>>
>> So not CLK_IS_CRITICAL?
> Yes, CLK_IS_CRITICAL is better, I will change it.
Same comment as above.
>>
>>> + },
>>> +};
>>> +
>> [...]
>>> +
>>> +/*
>>> + * cpu clock register base address is 0xfd000080
>>> + */
>>> +static struct clk_regmap *const a1_cpu_clk_regmaps[] = {
>>> + /* TODO */
>>
>> Can it be done?
> I plan to compelte cpu clock with the DVFS verified. And Some peripheral
> devices rely on this patch to send. I prefer to do it in the next patch.
>>
>>> +};
>>
>> .
>>
Powered by blists - more mailing lists