| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Tue, 01 Oct 2019 15:29:25 +0200
From: Jerome Brunet <jbrunet@...libre.com>
To: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Cc: narmstrong@...libre.com, linux-amlogic@...ts.infradead.org,
devicetree@...r.kernel.org, khilman@...libre.com,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-clk@...r.kernel.org
Subject: Re: [PATCH 2/6] clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller
On Sat 21 Sep 2019 at 17:18, Martin Blumenstingl <martin.blumenstingl@...glemail.com> wrote:
> The Meson8/Meson8b/Meson8m2 SoCs embed a DDR clock controller in the
> MMCBUS registers. There is no public documentation, but the u-boot GPL
> sources from the Amlogic BSP show that the DDR clock controller is
> identical on all three SoCs:
> #define CFG_DDR_CLK 792
> #define CFG_PLL_M (((CFG_DDR_CLK/12)*12)/24)
> #define CFG_PLL_N 1
> #define CFG_PLL_OD 1
>
> // from set_ddr_clock:
> t_ddr_pll_cntl= (CFG_PLL_OD << 16)|(CFG_PLL_N<<9)|(CFG_PLL_M<<0)
> writel(timing_reg->t_ddr_pll_cntl|(1<<29),AM_DDR_PLL_CNTL);
> writel(readl(AM_DDR_PLL_CNTL) & (~(1<<29)),AM_DDR_PLL_CNTL);
>
> // from hx_ddr_power_down_enter: shut down DDR PLL
> writel(readl(AM_DDR_PLL_CNTL)|(1<<30),AM_DDR_PLL_CNTL);
>
> do { ... } while((readl(AM_DDR_PLL_CNTL)&(1<<31))==0)
>
> This translates to:
> - AM_DDR_PLL_CNTL[29] is the reset bit
> - AM_DDR_PLL_CNTL[30] is the enable bit
> - AM_DDR_PLL_CNTL[31] is the lock bit
> - AM_DDR_PLL_CNTL[8:0] is the m value (assuming the width is 9 bits
> based on the start of the n value)
> - AM_DDR_PLL_CNTL[13:9] is the n value (assuming the width is 5 bits
> based on the start of the od)
> - AM_DDR_PLL_CNTL[17:16] is the od (assuming the width is 2 bits based
> on other PLLs on this SoC)
>
> Add a driver for this PLL setup because it's used as one of the inputs
> of the audio clocks. There may be more clocks inside that clock
> controller - those can be added in subsequent patches.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
> ---
> drivers/clk/meson/Makefile | 2 +-
> drivers/clk/meson/meson8-ddr.c | 153 +++++++++++++++++++++++++++++++++
> 2 files changed, 154 insertions(+), 1 deletion(-)
> create mode 100644 drivers/clk/meson/meson8-ddr.c
>
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index 3939f218587a..6eca2a406ee3 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -18,4 +18,4 @@ obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
> obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
> -obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
> +obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
> diff --git a/drivers/clk/meson/meson8-ddr.c b/drivers/clk/meson/meson8-ddr.c
> new file mode 100644
> index 000000000000..64ab4c27cce0
> --- /dev/null
> +++ b/drivers/clk/meson/meson8-ddr.c
> @@ -0,0 +1,153 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Amlogic Meson8 DDR clock controller
> + *
> + * Copyright (C) 2019 Martin Blumenstingl <martin.blumenstingl@...glemail.com>
> + */
> +
> +#include <dt-bindings/clock/meson8-ddr-clkc.h>
> +
> +#include <linux/platform_device.h>
> +#include <linux/mfd/syscon.h>
syscon is not used in the driver
> +#include <linux/of_device.h>
> +#include <linux/slab.h>
> +
> +#include "clk-regmap.h"
> +#include "clk-pll.h"
> +
> +#define AM_DDR_PLL_CNTL 0x00
> +#define AM_DDR_PLL_CNTL1 0x04
> +#define AM_DDR_PLL_CNTL2 0x08
> +#define AM_DDR_PLL_CNTL3 0x0c
> +#define AM_DDR_PLL_CNTL4 0x10
> +#define AM_DDR_PLL_STS 0x14
> +#define DDR_CLK_CNTL 0x18
> +#define DDR_CLK_STS 0x1c
> +
> +static struct clk_regmap meson8_ddr_pll_dco = {
> + .data = &(struct meson_clk_pll_data){
> + .en = {
> + .reg_off = AM_DDR_PLL_CNTL,
> + .shift = 30,
> + .width = 1,
> + },
> + .m = {
> + .reg_off = AM_DDR_PLL_CNTL,
> + .shift = 0,
> + .width = 9,
> + },
> + .n = {
> + .reg_off = AM_DDR_PLL_CNTL,
> + .shift = 9,
> + .width = 5,
> + },
> + .l = {
> + .reg_off = AM_DDR_PLL_CNTL,
> + .shift = 31,
> + .width = 1,
> + },
> + .rst = {
> + .reg_off = AM_DDR_PLL_CNTL,
> + .shift = 29,
> + .width = 1,
> + },
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "ddr_pll_dco",
> + .ops = &meson_clk_pll_ro_ops,
> + .parent_data = &(const struct clk_parent_data) {
> + .fw_name = "xtal",
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap meson8_ddr_pll = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = AM_DDR_PLL_CNTL,
> + .shift = 16,
> + .width = 2,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "ddr_pll",
> + .ops = &clk_regmap_divider_ro_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &meson8_ddr_pll_dco.hw
> + },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_hw_onecell_data meson8_ddr_clk_hw_onecell_data = {
> + .hws = {
> + [DDR_CLKID_DDR_PLL_DCO] = &meson8_ddr_pll_dco.hw,
> + [DDR_CLKID_DDR_PLL] = &meson8_ddr_pll.hw,
I wonder if onecell is not overkill for this driver. We won't expose the
DCO, so only the post divider remains
Do you expect this provider to have more than one leaf clock ?
If not, maybe you could use of_clk_hw_simple_get() instead ?
> + },
> + .num = 2,
> +};
> +
> +static struct clk_regmap *const meson8_ddr_clk_regmaps[] = {
> + &meson8_ddr_pll_dco,
> + &meson8_ddr_pll,
> +};
> +
> +static const struct regmap_config meson8_ddr_clkc_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .fast_io = true,
I think fast_io will default to true with memory based register.
Setting the max_register would be nice
> +};
> +
> +static int meson8_ddr_clkc_probe(struct platform_device *pdev)
> +{
> + struct regmap *regmap;
> + struct resource *res;
> + void __iomem *base;
> + struct clk_hw *hw;
> + int ret, i;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + regmap = devm_regmap_init_mmio(&pdev->dev, base,
> + &meson8_ddr_clkc_regmap_config);
> + if (IS_ERR(regmap))
> + return PTR_ERR(regmap);
> +
> + /* Populate regmap */
> + for (i = 0; i < ARRAY_SIZE(meson8_ddr_clk_regmaps); i++)
> + meson8_ddr_clk_regmaps[i]->map = regmap;
> +
> + /* Register all clks */
> + for (i = 0; i < meson8_ddr_clk_hw_onecell_data.num; i++) {
> + hw = meson8_ddr_clk_hw_onecell_data.hws[i];
> +
> + ret = devm_clk_hw_register(&pdev->dev, hw);
> + if (ret) {
> + dev_err(&pdev->dev, "Clock registration failed\n");
> + return ret;
> + }
> + }
> +
> + return devm_of_clk_add_hw_provider(&pdev->dev, of_clk_hw_onecell_get,
> + &meson8_ddr_clk_hw_onecell_data);
> +}
> +
> +static const struct of_device_id meson8_ddr_clkc_match_table[] = {
> + { .compatible = "amlogic,meson8-ddr-clkc" },
> + { .compatible = "amlogic,meson8b-ddr-clkc" },
> + { /* sentinel */ },
> +};
> +
> +static struct platform_driver meson8_ddr_clkc_driver = {
> + .probe = meson8_ddr_clkc_probe,
> + .driver = {
> + .name = "meson8-ddr-clkc",
> + .of_match_table = meson8_ddr_clkc_match_table,
> + },
> +};
> +
> +builtin_platform_driver(meson8_ddr_clkc_driver);
Powered by blists - more mailing lists