linux-kernel - Re: imx6: hdmi black screen issue after resume

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <CAOuPNLjMFPn5WLcotG26wy_ROhJZn39iywwOYG0imzjqeQ3jeg@mail.gmail.com>
Date:   Fri, 4 Oct 2019 15:47:57 +0530
From:   Pintu Agarwal <pintu.ping@...il.com>
To:     p.zabel@...gutronix.de, bob.beckett@...labora.com,
        dri-devel@...ts.freedesktop.org,
        open list <linux-kernel@...r.kernel.org>,
        "moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE" 
        <linux-arm-kernel@...ts.infradead.org>, linux-pm@...r.kernel.org
Subject: Re: imx6: hdmi black screen issue after resume

Hi,

On Sun, Sep 29, 2019 at 10:24 PM Pintu Agarwal <pintu.ping@...il.com> wrote:
>
> >
> > On Mon, Sep 23, 2019 at 1:28 PM Pintu Agarwal <pintu.ping@...il.com> wrote:
> > >
> > > Dear Philipp,
> > >
> > > I have a iMX6dl custom board with custom Linux Kernel 4.8.
> > > I have both LCD and HDMI connected to the board.
> > > And we are using weston/wayland as the display interface.
> > > In normal boot, both LCD and HDMI display is working fine.
> > >
> > > But, currently, for one of the requirement, I am trying to explore and
> > > support hibernation image booting on it.
> > > Currently, we are able to resume the system without display.
> > > Also, if we make the entire imx-drm as modules, and then install the
> > > modules after resume, even LCD is also coming up.
> > > But HDMI display is black out.
> > >

I just found the main root cause of the HDMI screen blackout issue
after system resume.
* HDMI is trying to get EDID data from the monitor using I2C interface.
* But its seems i2c_transfer is getting timeout after 5 retries.
* Thus EDID data is failing, and HDMI could not able to detect the monitor.

This is the logs:

[  441.104989] [drm:drm_helper_probe_single_connector_modes]
[CONNECTOR:29:HDMI-A-1] status updated from unknown to connected
[  441.116080]: drm_helper_probe_single_connector_modes - inside -
else override_edid
[  441.124416]: drm_helper_probe_single_connector_modes - inside -
else - drm_load_edid_firmware: count: 0
[  441.134546]: drm_helper_probe_single_connector_modes - calling - get_modes
[  441.142157]: dw_hdmi_connector_get_modes : called
[  441.147652]: dw_hdmi_connector_get_modes : called - calling -> drm_get_edid
[  441.155346]: drm_do_probe_ddc_edid : called!
[  441.660759]: drm_do_probe_ddc_edid : i2c_transfer: ret: -110, retry: 5
[  442.170758]: drm_do_probe_ddc_edid : i2c_transfer: ret: -110, retry: 4
[  442.680755]: drm_do_probe_ddc_edid : i2c_transfer: ret: -110, retry: 3
[  443.190755]: drm_do_probe_ddc_edid : i2c_transfer: ret: -110, retry: 2
[  443.700754]: drm_do_probe_ddc_edid : i2c_transfer: ret: -110, retry: 1
[  443.707989]: drm_get_edid : called - drm_probe_ddc - failed
[  443.714303] dwhdmi-imx 120000.hdmi: failed to get edid

Is there any clue, how to resolve this i2c failure issue, after resume?
This does not happen in normal booting case.

These are the steps I follow:
* Boot the system normally (without display) and install all imx-drm as modules.
* Then uninstall the modules in reverse order.
* Take the snapshot of the system (suspend to disk).
* Reboot the system and boot with the image.
* Install all the modules again.
* Then launch the Weston.
* During the weston launch in the beginning we observe this error.


Regards,
Pintu