| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20191011103340.26749-2-ludovic.desroches@microchip.com>
Date: Fri, 11 Oct 2019 12:33:38 +0200
From: Ludovic Desroches <ludovic.desroches@...rochip.com>
To: <linux-arm-kernel@...ts.infradead.org>,
<linux-mmc@...r.kernel.org>, <devicetree@...r.kernel.org>
CC: <ulf.hansson@...aro.org>, <nicolas.ferre@...rochip.com>,
<adrian.hunter@...el.com>, <linux-kernel@...r.kernel.org>,
<robh+dt@...nel.org>, <mark.rutland@....com>,
<claudiu.beznea@...rochip.com>, <Eugen.Hristev@...rochip.com>,
Ludovic Desroches <ludovic.desroches@...rochip.com>
Subject: [PATCH v2 2/3] mmc: sdhci-of-at91: rework clocks management to support SAM9x60 device
In the SAM9x60 SoC, there are only two clocks instead of three for the
SDHCI device. The base clk is no longer provided, it is generated
internally from the mult clk.
The values of the base clk and mul in the capabilities registers may not
reflect the reality as the mult clk is a programmable clock which can take
several rates. As we can't trust those values, take them from the clock
tree and update the capabilities according to.
As we can have the same pitfall, in some cases, with the SAMA5D2 Soc,
stop relying on capabilities too.
Signed-off-by: Ludovic Desroches <ludovic.desroches@...rochip.com>
---
Changes:
- v2: write caps0
drivers/mmc/host/sdhci-of-at91.c | 105 +++++++++++++++++--------------
1 file changed, 58 insertions(+), 47 deletions(-)
diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c
index e7d1920729fb..9a1ae16a5417 100644
--- a/drivers/mmc/host/sdhci-of-at91.c
+++ b/drivers/mmc/host/sdhci-of-at91.c
@@ -30,7 +30,14 @@
#define SDHCI_AT91_PRESET_COMMON_CONF 0x400 /* drv type B, programmable clock mode */
+struct sdhci_at91_soc_data {
+ const struct sdhci_pltfm_data *pdata;
+ bool baseclk_is_generated_internally;
+ unsigned int divider_for_baseclk;
+};
+
struct sdhci_at91_priv {
+ const struct sdhci_at91_soc_data *soc_data;
struct clk *hclock;
struct clk *gck;
struct clk *mainck;
@@ -130,12 +137,24 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
.set_power = sdhci_at91_set_power,
};
-static const struct sdhci_pltfm_data soc_data_sama5d2 = {
+static const struct sdhci_pltfm_data sdhci_sama5d2_pdata = {
.ops = &sdhci_at91_sama5d2_ops,
};
+static const struct sdhci_at91_soc_data soc_data_sama5d2 = {
+ .pdata = &sdhci_sama5d2_pdata,
+ .baseclk_is_generated_internally = false,
+};
+
+static const struct sdhci_at91_soc_data soc_data_sam9x60 = {
+ .pdata = &sdhci_sama5d2_pdata,
+ .baseclk_is_generated_internally = true,
+ .divider_for_baseclk = 2,
+};
+
static const struct of_device_id sdhci_at91_dt_match[] = {
{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
+ { .compatible = "microchip,sam9x60-sdhci", .data = &soc_data_sam9x60 },
{}
};
MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);
@@ -145,50 +164,37 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
- int ret;
unsigned int caps0, caps1;
unsigned int clk_base, clk_mul;
- unsigned int gck_rate, real_gck_rate;
+ unsigned int gck_rate, clk_base_rate;
unsigned int preset_div;
- /*
- * The mult clock is provided by as a generated clock by the PMC
- * controller. In order to set the rate of gck, we have to get the
- * base clock rate and the clock mult from capabilities.
- */
clk_prepare_enable(priv->hclock);
caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
- clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
- clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
- gck_rate = clk_base * 1000000 * (clk_mul + 1);
- ret = clk_set_rate(priv->gck, gck_rate);
- if (ret < 0) {
- dev_err(dev, "failed to set gck");
- clk_disable_unprepare(priv->hclock);
- return ret;
- }
- /*
- * We need to check if we have the requested rate for gck because in
- * some cases this rate could be not supported. If it happens, the rate
- * is the closest one gck can provide. We have to update the value
- * of clk mul.
- */
- real_gck_rate = clk_get_rate(priv->gck);
- if (real_gck_rate != gck_rate) {
- clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
- caps1 &= (~SDHCI_CLOCK_MUL_MASK);
- caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
- SDHCI_CLOCK_MUL_MASK);
- /* Set capabilities in r/w mode. */
- writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
- host->ioaddr + SDMMC_CACR);
- writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
- /* Set capabilities in ro mode. */
- writel(0, host->ioaddr + SDMMC_CACR);
- dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
- clk_mul, real_gck_rate);
- }
+
+ gck_rate = clk_get_rate(priv->gck);
+ if (priv->soc_data->baseclk_is_generated_internally)
+ clk_base_rate = gck_rate / priv->soc_data->divider_for_baseclk;
+ else
+ clk_base_rate = clk_get_rate(priv->mainck);
+
+ clk_base = clk_base_rate / 1000000;
+ clk_mul = gck_rate / clk_base_rate - 1;
+
+ caps0 &= (~SDHCI_CLOCK_V3_BASE_MASK);
+ caps0 |= ((clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK);
+ caps1 &= (~SDHCI_CLOCK_MUL_MASK);
+ caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK);
+ /* Set capabilities in r/w mode. */
+ writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN, host->ioaddr + SDMMC_CACR);
+ writel(caps0, host->ioaddr + SDHCI_CAPABILITIES_1);
+ writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
+ /* Set capabilities in ro mode. */
+ writel(0, host->ioaddr + SDMMC_CACR);
+
+ dev_info(dev, "update clk mul to %u as gck rate is %u Hz and clk base is %u Hz\n",
+ clk_mul, gck_rate, clk_base_rate);
/*
* We have to set preset values because it depends on the clk_mul
@@ -196,19 +202,19 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
* maximum sd clock value is 120 MHz instead of 208 MHz. For that
* reason, we need to use presets to support SDR104.
*/
- preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 24000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR12);
- preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR25);
- preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 100000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR50);
- preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 120000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR104);
- preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+ preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_DDR50);
@@ -303,7 +309,7 @@ static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
static int sdhci_at91_probe(struct platform_device *pdev)
{
const struct of_device_id *match;
- const struct sdhci_pltfm_data *soc_data;
+ const struct sdhci_at91_soc_data *soc_data;
struct sdhci_host *host;
struct sdhci_pltfm_host *pltfm_host;
struct sdhci_at91_priv *priv;
@@ -314,17 +320,22 @@ static int sdhci_at91_probe(struct platform_device *pdev)
return -EINVAL;
soc_data = match->data;
- host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
+ host = sdhci_pltfm_init(pdev, soc_data->pdata, sizeof(*priv));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
priv = sdhci_pltfm_priv(pltfm_host);
+ priv->soc_data = soc_data;
priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
if (IS_ERR(priv->mainck)) {
- dev_err(&pdev->dev, "failed to get baseclk\n");
- return PTR_ERR(priv->mainck);
+ if (soc_data->baseclk_is_generated_internally) {
+ priv->mainck = NULL;
+ } else {
+ dev_err(&pdev->dev, "failed to get baseclk\n");
+ return PTR_ERR(priv->mainck);
+ }
}
priv->hclock = devm_clk_get(&pdev->dev, "hclock");
--
2.23.0
Powered by blists - more mailing lists