linux-kernel - Re: [PATCH v2 2/3] pwm: stm32: split breakinput apply routine to ease PM support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20191016070322.GB1296874@ulmo>
Date:   Wed, 16 Oct 2019 09:03:22 +0200
From:   Thierry Reding <thierry.reding@...il.com>
To:     Fabrice Gasnier <fabrice.gasnier@...com>
Cc:     robh+dt@...nel.org, u.kleine-koenig@...gutronix.de,
        alexandre.torgue@...com, mark.rutland@....com,
        mcoquelin.stm32@...il.com, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        linux-pwm@...r.kernel.org, benjamin.gaignard@...com,
        linux-stm32@...md-mailman.stormreply.com
Subject: Re: [PATCH v2 2/3] pwm: stm32: split breakinput apply routine to
 ease PM support

On Fri, Oct 04, 2019 at 02:53:52PM +0200, Fabrice Gasnier wrote:
> Split breakinput routine that configures STM32 timers 'break' safety
> feature upon probe, into two routines:
> - stm32_pwm_apply_breakinputs() sets all the break inputs into registers.
> - stm32_pwm_probe_breakinputs() probes the device tree break input settings
>   before calling stm32_pwm_apply_breakinputs()
> 
> This is a precursor patch to ease PM support. Registers content may get
> lost during low power. So, break input settings applied upon probe need
> to be restored upon resume (e.g. by calling stm32_pwm_apply_breakinputs()).
> 
> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@...com>
> ---
>  drivers/pwm/pwm-stm32.c | 48 ++++++++++++++++++++++++++++--------------------
>  1 file changed, 28 insertions(+), 20 deletions(-)

Applied, thanks. I've made some minor changes, mostly for consistency
with other drivers and the PWM core. See below.

> diff --git a/drivers/pwm/pwm-stm32.c b/drivers/pwm/pwm-stm32.c
> index 359b085..cf8658c 100644
> --- a/drivers/pwm/pwm-stm32.c
> +++ b/drivers/pwm/pwm-stm32.c
> @@ -19,6 +19,12 @@
>  #define CCMR_CHANNEL_MASK  0xFF
>  #define MAX_BREAKINPUT 2
>  
> +struct stm32_breakinput {
> +	u32 index;
> +	u32 level;
> +	u32 filter;
> +};
> +
>  struct stm32_pwm {
>  	struct pwm_chip chip;
>  	struct mutex lock; /* protect pwm config/enable */
> @@ -26,15 +32,11 @@ struct stm32_pwm {
>  	struct regmap *regmap;
>  	u32 max_arr;
>  	bool have_complementary_output;
> +	struct stm32_breakinput breakinput[MAX_BREAKINPUT];
> +	unsigned int nbreakinput;

I changed these to breakinputs and num_breakinputs since they are
slightly more consistent with the naming elsewhere in PWM.

>  	u32 capture[4] ____cacheline_aligned; /* DMA'able buffer */
>  };
>  
> -struct stm32_breakinput {
> -	u32 index;
> -	u32 level;
> -	u32 filter;
> -};
> -
>  static inline struct stm32_pwm *to_stm32_pwm_dev(struct pwm_chip *chip)
>  {
>  	return container_of(chip, struct stm32_pwm, chip);
> @@ -512,15 +514,27 @@ static int stm32_pwm_set_breakinput(struct stm32_pwm *priv,
>  	return (bdtr & bke) ? 0 : -EINVAL;
>  }
>  
> -static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv,
> +static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv)
> +{
> +	int i, ret = 0;

Made i unsigned int.

> +
> +	for (i = 0; i < priv->nbreakinput && !ret; i++) {
> +		ret = stm32_pwm_set_breakinput(priv,
> +					       priv->breakinput[i].index,
> +					       priv->breakinput[i].level,
> +					       priv->breakinput[i].filter);
> +	}

I thought this was a little odd, so I changed it to explicitly check the
value of ret and return on error.

> +
> +	return ret;

And then this became "return 0;"

> +}
> +
> +static int stm32_pwm_probe_breakinputs(struct stm32_pwm *priv,
>  				       struct device_node *np)
>  {
> -	struct stm32_breakinput breakinput[MAX_BREAKINPUT];
> -	int nb, ret, i, array_size;
> +	int nb, ret, array_size;
>  
>  	nb = of_property_count_elems_of_size(np, "st,breakinput",
>  					     sizeof(struct stm32_breakinput));
> -

Dropped this since it made the code look cluttered.

Thierry

>  	/*
>  	 * Because "st,breakinput" parameter is optional do not make probe
>  	 * failed if it doesn't exist.
> @@ -531,20 +545,14 @@ static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv,
>  	if (nb > MAX_BREAKINPUT)
>  		return -EINVAL;
>  
> +	priv->nbreakinput = nb;
>  	array_size = nb * sizeof(struct stm32_breakinput) / sizeof(u32);
>  	ret = of_property_read_u32_array(np, "st,breakinput",
> -					 (u32 *)breakinput, array_size);
> +					 (u32 *)priv->breakinput, array_size);
>  	if (ret)
>  		return ret;
>  
> -	for (i = 0; i < nb && !ret; i++) {
> -		ret = stm32_pwm_set_breakinput(priv,
> -					       breakinput[i].index,
> -					       breakinput[i].level,
> -					       breakinput[i].filter);
> -	}
> -
> -	return ret;
> +	return stm32_pwm_apply_breakinputs(priv);
>  }
>  
>  static void stm32_pwm_detect_complementary(struct stm32_pwm *priv)
> @@ -614,7 +622,7 @@ static int stm32_pwm_probe(struct platform_device *pdev)
>  	if (!priv->regmap || !priv->clk)
>  		return -EINVAL;
>  
> -	ret = stm32_pwm_apply_breakinputs(priv, np);
> +	ret = stm32_pwm_probe_breakinputs(priv, np);
>  	if (ret)
>  		return ret;
>  
> -- 
> 2.7.4
> 

Download attachment "signature.asc" of type "application/pgp-signature" (834 bytes)