Message-ID: <20191028134247.GA85892@google.com>
Date:   Mon, 28 Oct 2019 08:42:47 -0500
From:   Bjorn Helgaas <helgaas@...nel.org>
To:     Mika Westerberg <mika.westerberg@...ux.intel.com>
Cc:     "Rafael J. Wysocki" <rjw@...ysocki.net>,
        Len Brown <lenb@...nel.org>, Lukas Wunner <lukas@...ner.de>,
        Keith Busch <keith.busch@...el.com>,
        Alex Williamson <alex.williamson@...hat.com>,
        Alexandru Gagniuc <mr.nuke.me@...il.com>,
        Kai-Heng Feng <kai.heng.feng@...onical.com>,
        Matthias Andree <matthias.andree@....de>,
        Paul Menzel <pmenzel@...gen.mpg.de>,
        Nicholas Johnson <nicholas.johnson-opensource@...look.com.au>,
        linux-pci@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2 2/2] PCI: Add missing link delays required by the PCIe
 spec

On Mon, Oct 28, 2019 at 01:28:52PM +0200, Mika Westerberg wrote:
> On Sat, Oct 26, 2019 at 09:19:38AM -0500, Bjorn Helgaas wrote:
> > On Fri, Oct 04, 2019 at 03:39:47PM +0300, Mika Westerberg wrote:
> > > Currently Linux does not follow PCIe spec regarding the required delays
> > > after reset. A concrete example is a Thunderbolt add-in-card that
> > > consists of a PCIe switch and two PCIe endpoints:
> > > 
> > >   +-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
> > >                                   +-01.0-[04-36]-- DS hotplug port
> > >                                   +-02.0-[37]----00.0 xHCI controller
> > >                                   \-04.0-[38-6b]-- DS hotplug port
> > > 
> > > The root port (1b.0) and the PCIe switch downstream ports are all PCIe
> > > gen3 so they support 8GT/s link speeds.
> > > 
> > > We wait for the PCIe hierarchy to enter D3cold (runtime):
> > > 
> > >   pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
> > > 
> > > When it wakes up from D3cold, according to the PCIe 4.0 section 5.8 the
> > > PCIe switch is put to reset and its power is re-applied. This means that
> > > we must follow the rules in PCIe 4.0 section 6.6.1.
> > 
> > If you have the PCIe 5.0 spec, can you update these references to
> > that?  If not, I'm happy to do it for you.
> 
> I do have it and sure, I'll update them.
> 
> > > For the PCIe gen3 ports we are dealing with here, the following applies:
> > > 
> > >   With a Downstream Port that supports Link speeds greater than 5.0
> > >   GT/s, software must wait a minimum of 100 ms after Link training
> > >   completes before sending a Configuration Request to the device
> > >   immediately below that Port. Software can determine when Link training
> > >   completes by polling the Data Link Layer Link Active bit or by setting
> > >   up an associated interrupt (see Section 6.7.3.3).
> > > 
> > > Translating this into the above topology we would need to do this (DLLLA
> > > stands for Data Link Layer Link Active):
> > > 
> > >   0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
> > >   0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
> > >   0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
> > > 
> > > I've instrumented the kernel with some additional logging so we can see
> > > the actual delays performed:
> > > 
> > >   pcieport 0000:00:1b.0: power state changed by ACPI to D0
> > >   pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
> > >   pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
> > >   pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
> > >   pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
> > > 
> > > For the switch upstream port (01:00.0 reachable through 00:1b.0 root
> > > port) we wait for 100 ms but not taking into account the DLLLA
> > > requirement. We then wait 10 ms for D3hot -> D0 transition of the root
> > > port and the two downstream hotplug ports. This means that we deviate
> > > from what the spec requires.
> > > 
> > > Performing the same check for system sleep (s2idle) transitions it turns
> > > out to be even worse. None of the mandatory delays are performed. If
> > > this would be S3 instead of s2idle then according to PCI FW spec 3.2
> > > section 4.6.8. there is a specific _DSM that allows the OS to skip the
> > > delays but this platform does not provide the _DSM and does not go to S3
> > > anyway so no firmware is involved that could already handle these
> > > delays.
> > > 
> > > On this particular platform these delays are not actually needed because
> > > there is an additional delay as part of the ACPI power resource that is
> > > used to turn on power to the hierarchy but since that additional delay
> > > is not required by any of standards (PCIe, ACPI) it is not present in
> > > the Intel Ice Lake, for example where missing the mandatory delays
> > > causes pciehp to start tearing down the stack too early (links are not
> > > yet trained). Below is an example how it looks like when this happens:
> > > 
> > >   pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
> > >   pcieport 0000:87:04.0: PME# disabled
> > >   pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain:bus:dev = 0000:86:00
> > >   pcieport 0000:86:00.0: Refused to change power state, currently in D3
> > >   pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
> > >   pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
> > >   ...
> > > 
> > > There is also one reported case (see the bugzilla link below) where the
> > > missing delay causes xHCI on a Titan Ridge controller fail to runtime
> > > resume when USB-C dock is plugged. This does not involve pciehp but
> > > instead it PCI core fails to runtime resume the xHCI device:
> > > 
> > >   pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
> > >   pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
> > >   xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
> > >   xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
> > >   xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
> > >   ...
> > > 
> > > For this reason, introduce a new function pci_bridge_wait_for_secondary_bus()
> > > that is called on PCI core resume and runtime resume paths accordingly
> > > if the bridge entered D3cold (and thus went through reset).
> > > 
> > > This is second attempt to add the missing delays. The previous solution
> > > in commit c2bf1fc212f7 ("PCI: Add missing link delays required by the
> > > PCIe spec") was reverted because of two issues it caused:
> > > 
> > >   1. One system become unresponsive after S3 resume due to PME service
> > >      spinning in pcie_pme_work_fn(). The root port in question reports
> > >      that the xHCI sent PME but the xHCI device itself does not have PME
> > >      status set. The PME status bit is never cleared in the root port
> > >      resulting the indefinite loop in pcie_pme_work_fn().
> > > 
> > >   2. Slows down resume if the root/downstream port does not support
> > >      Data Link Layer Active Reporting because pcie_wait_for_link_delay()
> > >      waits 1100 ms in that case.
> > > 
> > > This version should avoid the above issues because we restrict the delay
> > > to happen only if the port went into D3cold.
> > > 
> > > Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
> > > Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
> > > Reported-by: Kai-Heng Feng <kai.heng.feng@...onical.com>
> > > Tested-by: Kai-Heng Feng <kai.heng.feng@...onical.com>
> > > Signed-off-by: Mika Westerberg <mika.westerberg@...ux.intel.com>
> > > ---
> > >  drivers/pci/pci-driver.c | 18 ++++++++
> > >  drivers/pci/pci.c        | 92 +++++++++++++++++++++++++++++++++++++---
> > >  drivers/pci/pci.h        |  1 +
> > >  3 files changed, 104 insertions(+), 7 deletions(-)
> > > 
> > > diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
> > > index a8124e47bf6e..74a144c9cf4e 100644
> > > --- a/drivers/pci/pci-driver.c
> > > +++ b/drivers/pci/pci-driver.c
> > > @@ -917,6 +917,7 @@ static int pci_pm_suspend_noirq(struct device *dev)
> > >  static int pci_pm_resume_noirq(struct device *dev)
> > >  {
> > >  	struct pci_dev *pci_dev = to_pci_dev(dev);
> > > +	bool d3cold = pci_dev->current_state == PCI_D3cold;
> > >  	struct device_driver *drv = dev->driver;
> > >  	int error = 0;
> > >  
> > > @@ -947,6 +948,14 @@ static int pci_pm_resume_noirq(struct device *dev)
> > >  
> > >  	pcie_pme_root_status_cleanup(pci_dev);
> > >  
> > > +	/*
> > > +	 * If the hierarchy went into D3cold wait for the secondary bus to
> > > +	 * become accessible. This is important for PCIe to prevent pciehp
> > > +	 * from tearing down the downstream devices too soon.

> > Can we move this closer to where we initiate the reset?  It's pretty
> > hard to tell from looking at pci_pm_resume_noirq() that there's a
> > reset happening here.
> 
> Well we actually don't do explicit reset but instead we power the thing
> on from D3cold.

The point is that it's too hard to maintain unless we can connect the
delay with the related hardware event.

> > For D3cold->D0, I guess that would be somewhere down in
> > platform_pci_set_power_state()?  Maybe acpi_pci_set_power_state()?
> > What about the mid_pci_set_power_state() path?  Does that need this
> > too?
> 
> I can take a look if it can be placed there. Yes,
> mid_pci_set_power_state() may at least in theory need it too although I
> don't remember any MID platforms with real PCIe devices.

I don't know how the OS is supposed to know if these are real PCIe
devices or not.  If we don't know, we have to assume they work per
spec and may require the delays per spec.

> > In the ACPI spec, _PS0 doesn't say anything about delays.  _ON (which
> > I assume is not for PCI devices themselves) *does* say firmware is
> > responsible for sequencing delays, so I would tend to assume it's
> > really firmware's job and we shouldn't need to do this in the kernel
> > at all.
> 
> _ON is also for PCI device itself but all those methods are not just for
> PCI so they don't really talk about any PCI specific delays. You need to
> look at other specs. For example PCI FW spec v3.2 section 4.6.9 says
> this about the _DSM that can be used to decrease the delays:
> 
>   This function is optional. If the platform does not provide it, the
>   operating system must adhere to all timing requirements as described
>   in the PCI Express Base specification and/or applicable form factor
>   specification, including values contained in Readiness Time Reporting
>   capability structure.

I don't think this _DSM tells us anything about delays after _ON,
_PS0, etc.  All the delays it mentions are for transitions the OS can
do natively without the _ON, _PS0, etc methods.  It makes no mention
of those methods, or of the D3cold->D0 transition (which would require
them).

> Relevant PCIe spec section is 6.6.1 (also referenced in the changelog).
> 
> [If you have access to ECN titled "Async Hot-Plug Updates" (you can find
> it in PCI-SIG site) that document has a nice table about the delays in
> page 32. It compares surprise hotplug with downstream port containment
> for async hotplug]

Thanks for the pointer, that ECN looks very useful.  It does talk
about delays in general, but I don't see anything that clarifies
whether ACPI methods or the OS is responsible for them.

> > What about D3hot->D0?  When a bridge (Root Port or Switch Downstream
> > Port) is in D3hot, I'm not really clear on the state of its link.  If
> > the link is down, I assume putting the bridge in D0 will bring it up
> > and we'd have to wait for that?  If so, we'd need to do something in
> > the reset path, e.g., pci_pm_reset()?
> 
> AFAIK the link goes into L1 when the function is programmed to any other
> D state than D0. 

Yes, and the "function" here is the one on the *downstream* end, e.g.,
the Endpoint or Switch Upstream Port.  When the upstream bridge (Root
Port or Switch Downstream Port) is in a non-D0 state, the downstream
component is unreachable (memory, I/O, and type 1 config requests are
terminated by the bridge as unsupported requests).

> If we don't put the device into D3cold then I think it
> stays in L1 where it can be brought back by writing D0 to PM register
> which does not need any other delay than the D3hot -> D0 (10ms).

In pci_pm_reset(), we're doing the D0->D3hot->D0 transitions
specifically to do a reset, so No_Soft_Reset is false.  Doesn't 6.6.1
say we need at least 100ms here?

> [There is a table in PCIe spec 5.0 section 5.3.2 that shows the link
> state and power management D-state relationship.]

Powered by blists - more mailing lists