| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20191106165835.2863-7-stephan@gerhold.net>
Date: Wed, 6 Nov 2019 17:58:34 +0100
From: Stephan Gerhold <stephan@...hold.net>
To: Linus Walleij <linus.walleij@...aro.org>
Cc: David Airlie <airlied@...ux.ie>, Daniel Vetter <daniel@...ll.ch>,
dri-devel@...ts.freedesktop.org, linux-kernel@...r.kernel.org,
Stephan Gerhold <stephan@...hold.net>
Subject: [PATCH 6/7] drm/mcde: dsi: Enable clocks in pre_enable() instead of mode_set()
The DSI initialization sequence incorrectly assumes that the mode_set()
function of the DRM bridge is always called when (re-)enabling the display.
This is not necessarily the case.
Keeping the device idle in the framebuffer console for a while results
in the display being turned off using the disable() function. However,
as soon as any key is pressed only (pre_)enable() are called.
mode_set() is skipped because the mode has not been changed.
In this case, the DSI HS/LP clocks are never turned back on,
preventing the display from working.
Fix this by moving a part of the initialization sequence from
mode_set() to pre_enable(). Keep most of the video mode setup in
mode_set() since most of the registers are only dependent on the mode
that is set for the panel - there is no need to write them again each
time we re-enable the display.
Signed-off-by: Stephan Gerhold <stephan@...hold.net>
---
drivers/gpu/drm/mcde/mcde_dsi.c | 67 ++++++++++++++++++---------------
1 file changed, 37 insertions(+), 30 deletions(-)
diff --git a/drivers/gpu/drm/mcde/mcde_dsi.c b/drivers/gpu/drm/mcde/mcde_dsi.c
index df963e078c35..03896a1f339a 100644
--- a/drivers/gpu/drm/mcde/mcde_dsi.c
+++ b/drivers/gpu/drm/mcde/mcde_dsi.c
@@ -562,21 +562,6 @@ static void mcde_dsi_setup_video_mode(struct mcde_dsi *d,
DSI_VID_VCA_SETTING2_EXACT_BURST_LIMIT_SHIFT;
writel(val, d->regs + DSI_VID_VCA_SETTING2);
- /* Put IF1 into video mode */
- val = readl(d->regs + DSI_MCTL_MAIN_DATA_CTL);
- val |= DSI_MCTL_MAIN_DATA_CTL_IF1_MODE;
- writel(val, d->regs + DSI_MCTL_MAIN_DATA_CTL);
-
- /* Disable command mode on IF1 */
- val = readl(d->regs + DSI_CMD_MODE_CTL);
- val &= ~DSI_CMD_MODE_CTL_IF1_LP_EN;
- writel(val, d->regs + DSI_CMD_MODE_CTL);
-
- /* Enable some error interrupts */
- val = readl(d->regs + DSI_VID_MODE_STS_CTL);
- val |= DSI_VID_MODE_STS_CTL_ERR_MISSING_VSYNC;
- val |= DSI_VID_MODE_STS_CTL_ERR_MISSING_DATA;
- writel(val, d->regs + DSI_VID_MODE_STS_CTL);
}
static void mcde_dsi_start(struct mcde_dsi *d)
@@ -700,26 +685,13 @@ static void mcde_dsi_bridge_enable(struct drm_bridge *bridge)
dev_info(d->dev, "enable DSI master\n");
};
-static void mcde_dsi_bridge_mode_set(struct drm_bridge *bridge,
- const struct drm_display_mode *mode,
- const struct drm_display_mode *adj)
+static void mcde_dsi_bridge_pre_enable(struct drm_bridge *bridge)
{
struct mcde_dsi *d = bridge_to_mcde_dsi(bridge);
- unsigned long pixel_clock_hz = mode->clock * 1000;
unsigned long hs_freq, lp_freq;
u32 val;
int ret;
- if (!d->mdsi) {
- dev_err(d->dev, "no DSI device attached to encoder!\n");
- return;
- }
-
- dev_info(d->dev, "set DSI master to %dx%d %lu Hz %s mode\n",
- mode->hdisplay, mode->vdisplay, pixel_clock_hz,
- (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO) ? "VIDEO" : "CMD"
- );
-
/* Copy maximum clock frequencies */
if (d->mdsi->lp_rate)
lp_freq = d->mdsi->lp_rate;
@@ -758,7 +730,21 @@ static void mcde_dsi_bridge_mode_set(struct drm_bridge *bridge,
d->hs_freq);
if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
- mcde_dsi_setup_video_mode(d, mode);
+ /* Put IF1 into video mode */
+ val = readl(d->regs + DSI_MCTL_MAIN_DATA_CTL);
+ val |= DSI_MCTL_MAIN_DATA_CTL_IF1_MODE;
+ writel(val, d->regs + DSI_MCTL_MAIN_DATA_CTL);
+
+ /* Disable command mode on IF1 */
+ val = readl(d->regs + DSI_CMD_MODE_CTL);
+ val &= ~DSI_CMD_MODE_CTL_IF1_LP_EN;
+ writel(val, d->regs + DSI_CMD_MODE_CTL);
+
+ /* Enable some error interrupts */
+ val = readl(d->regs + DSI_VID_MODE_STS_CTL);
+ val |= DSI_VID_MODE_STS_CTL_ERR_MISSING_VSYNC;
+ val |= DSI_VID_MODE_STS_CTL_ERR_MISSING_DATA;
+ writel(val, d->regs + DSI_VID_MODE_STS_CTL);
} else {
/* Command mode, clear IF1 ID */
val = readl(d->regs + DSI_CMD_MODE_CTL);
@@ -772,6 +758,26 @@ static void mcde_dsi_bridge_mode_set(struct drm_bridge *bridge,
}
}
+static void mcde_dsi_bridge_mode_set(struct drm_bridge *bridge,
+ const struct drm_display_mode *mode,
+ const struct drm_display_mode *adj)
+{
+ struct mcde_dsi *d = bridge_to_mcde_dsi(bridge);
+
+ if (!d->mdsi) {
+ dev_err(d->dev, "no DSI device attached to encoder!\n");
+ return;
+ }
+
+ dev_info(d->dev, "set DSI master to %dx%d %u Hz %s mode\n",
+ mode->hdisplay, mode->vdisplay, mode->clock * 1000,
+ (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO) ? "VIDEO" : "CMD"
+ );
+
+ if (d->mdsi->mode_flags & MIPI_DSI_MODE_VIDEO)
+ mcde_dsi_setup_video_mode(d, mode);
+}
+
static void mcde_dsi_wait_for_command_mode_stop(struct mcde_dsi *d)
{
u32 val;
@@ -863,6 +869,7 @@ static const struct drm_bridge_funcs mcde_dsi_bridge_funcs = {
.mode_set = mcde_dsi_bridge_mode_set,
.disable = mcde_dsi_bridge_disable,
.enable = mcde_dsi_bridge_enable,
+ .pre_enable = mcde_dsi_bridge_pre_enable,
};
static int mcde_dsi_bind(struct device *dev, struct device *master,
--
2.23.0
Powered by blists - more mailing lists