Date:   Thu, 7 Nov 2019 21:50:30 +0200
From:   Laurent Pinchart <laurent.pinchart@...asonboard.com>
To:     Fabrizio Castro <fabrizio.castro@...renesas.com>
Cc:     David Airlie <airlied@...ux.ie>, Daniel Vetter <daniel@...ll.ch>,
        Kieran Bingham <kieran.bingham+renesas@...asonboard.com>,
        dri-devel@...ts.freedesktop.org, linux-renesas-soc@...r.kernel.org,
        linux-kernel@...r.kernel.org, Simon Horman <horms@...ge.net.au>,
        Geert Uytterhoeven <geert+renesas@...der.be>,
        Chris Paterson <Chris.Paterson2@...esas.com>,
        Biju Das <biju.das@...renesas.com>,
        Jacopo Mondi <jacopo+renesas@...ndi.org>, sam@...nborg.org
Subject: Re: [PATCH v3 4/8] drm: rcar-du: lvds: Add dual-LVDS panels support

Hi Fabrizio,

Thank you for the patch.

On Wed, Aug 28, 2019 at 07:36:38PM +0100, Fabrizio Castro wrote:
> The driver doesn't support dual-link LVDS displays, and the way
> it identifies bridges won't allow for dual-LVDS displays to be
> connected. Also, it's not possible to swap even and odd pixels
> around in case the wiring isn't taking advantage of the default
> hardware configuration. Further more, the "mode" of the companion
> encoder should be same as the mode of the primary encoder.
> 
> Rework the driver to improve all of the above, so that it can
> support dual-LVDS displays.

That's lots of changes in one patch, could it be split to ease review ?
Also, should the commit message be reworded to explain what the patch
does, instead of enumerating issues ? When there's a single issue being
addressed in a patch it's usually fine, but there the change is larger,
without an explanation of how you intend to fix the issues I can't tell
if the code really matches your intent.

> Signed-off-by: Fabrizio Castro <fabrizio.castro@...renesas.com>
> 
> ---
> v2->v3:
> * reworked to take advantange of the new dt-bindings
> * squashed in the patche for fixing the companion's mode
> 
> Laurent,
> 
> unfortunately the best way to get the companion encoder to use
> the same mode as the primary encoder is setting the mode directly
> without calling into rcar_lvds_mode_set for the companion encoder,
> as the below test fails for the companion encoder in
> rcar_lvds_get_lvds_mode:
> if (!info->num_bus_formats || !info->bus_formats)

Would "[PATCH] drm: rcar-du: lvds: Get mode from state" help here ?
Maybe you could review that patch, I could then include it in my -next
branch, your work would be simplified, and everybody would be happy ?
:-)

> Anyhow, setting the mode for the companion encoder doesn't seem
> to be mandary according to the experiments I have been running,
> but the HW User's Manual doesn't really say much about this,
> therefore I think the safest option is still to set the mode for
> the companion encoder.

I agree it should be done.

> ---
>  drivers/gpu/drm/rcar-du/rcar_lvds.c | 110 +++++++++++++++++++++---------------
>  1 file changed, 65 insertions(+), 45 deletions(-)
> 
> diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
> index 3fe0b86..dfec5e7 100644
> --- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
> +++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
> @@ -20,6 +20,8 @@
>  #include <drm/drm_atomic.h>
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_bridge.h>
> +#include <drm/drm_bus_timings.h>
> +#include <drm/drm_of.h>
>  #include <drm/drm_panel.h>
>  #include <drm/drm_probe_helper.h>
>  
> @@ -69,6 +71,7 @@ struct rcar_lvds {
>  
>  	struct drm_bridge *companion;
>  	bool dual_link;
> +	bool stripe_swap_data;
>  };
>  
>  #define bridge_to_rcar_lvds(b) \
> @@ -439,12 +442,20 @@ static void rcar_lvds_enable(struct drm_bridge *bridge)
>  	rcar_lvds_write(lvds, LVDCHCR, lvdhcr);
>  
>  	if (lvds->info->quirks & RCAR_LVDS_QUIRK_DUAL_LINK) {
> -		/*
> -		 * Configure vertical stripe based on the mode of operation of
> -		 * the connected device.
> -		 */
> -		rcar_lvds_write(lvds, LVDSTRIPE,
> -				lvds->dual_link ? LVDSTRIPE_ST_ON : 0);
> +		u32 lvdstripe = 0;
> +
> +		if (lvds->dual_link)
> +			/*
> +			 * Configure vertical stripe based on the mode of
> +			 * operation of the connected device.
> +			 *
> +			 * ST_SWAP from LVD1STRIPE is reserved, do not set
> +			 * in the companion LVDS
> +			 */
> +			lvdstripe = LVDSTRIPE_ST_ON |
> +				(lvds->companion && lvds->stripe_swap_data ?
> +				 LVDSTRIPE_ST_SWAP : 0);
> +		rcar_lvds_write(lvds, LVDSTRIPE, lvdstripe);
>  	}
>  
>  	/*
> @@ -603,6 +614,11 @@ static void rcar_lvds_mode_set(struct drm_bridge *bridge,
>  	lvds->display_mode = *adjusted_mode;
>  
>  	rcar_lvds_get_lvds_mode(lvds);
> +	if (lvds->companion) {
> +		struct rcar_lvds *companion_lvds = bridge_to_rcar_lvds(
> +							lvds->companion);
> +		companion_lvds->mode = lvds->mode;
> +	}
>  }
>  
>  static int rcar_lvds_attach(struct drm_bridge *bridge)
> @@ -667,9 +683,10 @@ EXPORT_SYMBOL_GPL(rcar_lvds_dual_link);
>  static int rcar_lvds_parse_dt_companion(struct rcar_lvds *lvds)
>  {
>  	const struct of_device_id *match;
> -	struct device_node *companion;
> +	struct device_node *companion, *p0 = NULL, *p1 = NULL;
>  	struct device *dev = lvds->dev;
> -	int ret = 0;
> +	struct rcar_lvds *companion_lvds;
> +	int ret = 0, dual_link;
>  
>  	/* Locate the companion LVDS encoder for dual-link operation, if any. */
>  	companion = of_parse_phandle(dev->of_node, "renesas,companion", 0);
> @@ -687,16 +704,50 @@ static int rcar_lvds_parse_dt_companion(struct rcar_lvds *lvds)
>  		goto done;
>  	}
>  
> +	/*
> +	 * We need to work out if the sink is expecting us to function in
> +	 * dual-link mode. We do this by looking at the DT port nodes we are
> +	 * connected to, if they are marked as expecting even pixels and
> +	 * odd pixels than we need to enable vertical stripe output
> +	 */
> +	p0 = of_graph_get_port_by_id(dev->of_node, 1);
> +	p1 = of_graph_get_port_by_id(companion, 1);
> +	dual_link = drm_of_lvds_get_dual_link_configuration(p0, p1);

You can call of_node_put(p0) and of_node_put(p1) here instead of adding
them at the end of the function.

> +	if (dual_link >= DRM_LVDS_DUAL_LINK_EVEN_ODD_PIXELS) {
> +		dev_dbg(dev, "Dual-link configuration detected\n");
> +		lvds->dual_link = true;
> +	} else {
> +		/* dual-link mode is not required */
> +		dev_dbg(dev, "Single-link configuration detected\n");
> +		goto done;
> +	}

Missing blank line here.

> +	/*
> +	 * We may need to swap even and odd pixels around in case the wiring
> +	 * doesn't match the default configuration.
> +	 * By default we generate even pixels from this encoder and odd pixels
> +	 * from the companion encoder, but if p0 is connected to the port
> +	 * expecting ood pixels, and p1 is connected to the port expecting even
> +	 * pixels, then we need to swap even and odd pixels around
> +	 */
> +	if (dual_link == DRM_LVDS_DUAL_LINK_ODD_EVEN_PIXELS) {
> +		dev_dbg(dev, "Data swapping required\n");
> +		lvds->stripe_swap_data = true;
> +	}
> +
>  	lvds->companion = of_drm_find_bridge(companion);
>  	if (!lvds->companion) {
>  		ret = -EPROBE_DEFER;
>  		goto done;
>  	}
> +	companion_lvds = bridge_to_rcar_lvds(lvds->companion);
> +	companion_lvds->dual_link = lvds->dual_link;

I don't like poking directly in the companion like this :-( Can't we let
the companion detect dual link mode itself ?

>  
>  	dev_dbg(dev, "Found companion encoder %pOF\n", companion);
>  
>  done:
>  	of_node_put(companion);
> +	of_node_put(p0);
> +	of_node_put(p1);
>  
>  	return ret;
>  }
> @@ -704,10 +755,7 @@ static int rcar_lvds_parse_dt_companion(struct rcar_lvds *lvds)
>  static int rcar_lvds_parse_dt(struct rcar_lvds *lvds)
>  {
>  	struct device_node *local_output = NULL;
> -	struct device_node *remote_input = NULL;
>  	struct device_node *remote = NULL;
> -	struct device_node *node;
> -	bool is_bridge = false;
>  	int ret = 0;
>  
>  	local_output = of_graph_get_endpoint_by_regs(lvds->dev->of_node, 1, 0);
> @@ -735,45 +783,17 @@ static int rcar_lvds_parse_dt(struct rcar_lvds *lvds)
>  		goto done;
>  	}
>  

I think you can also drop all the code above.

> -	remote_input = of_graph_get_remote_endpoint(local_output);
> -
> -	for_each_endpoint_of_node(remote, node) {
> -		if (node != remote_input) {
> -			/*
> -			 * We've found one endpoint other than the input, this
> -			 * must be a bridge.
> -			 */
> -			is_bridge = true;
> -			of_node_put(node);
> -			break;
> -		}
> -	}
> -
> -	if (is_bridge) {
> -		lvds->next_bridge = of_drm_find_bridge(remote);
> -		if (!lvds->next_bridge) {
> -			ret = -EPROBE_DEFER;
> -			goto done;
> -		}
> -
> -		if (lvds->info->quirks & RCAR_LVDS_QUIRK_DUAL_LINK)
> -			lvds->dual_link = lvds->next_bridge->timings
> -					? lvds->next_bridge->timings->dual_link
> -					: false;

Aren't you breaking backward compatibility with this change ? Unless I'm
mistaken you're now requiring the new DT properties, and the existing DT
that include a thc63lvd1024 won't have them.

> -	} else {
> -		lvds->panel = of_drm_find_panel(remote);
> -		if (IS_ERR(lvds->panel)) {
> -			ret = PTR_ERR(lvds->panel);
> -			goto done;
> -		}
> +	ret = drm_of_find_panel_or_bridge(lvds->dev->of_node, 1, 0,
> +					  &lvds->panel, &lvds->next_bridge);
> +	if (ret) {
> +		ret = -EPROBE_DEFER;

Shouldn't you return ret instead of overriding it ?

> +		goto done;
>  	}
> -
> -	if (lvds->dual_link)
> +	if (lvds->info->quirks & RCAR_LVDS_QUIRK_DUAL_LINK)
>  		ret = rcar_lvds_parse_dt_companion(lvds);
>  
>  done:
>  	of_node_put(local_output);
> -	of_node_put(remote_input);
>  	of_node_put(remote);
>  
>  	/*

-- 
Regards,

Laurent Pinchart

Powered by blists - more mailing lists