bootcmd=FS2:\Image.2 root=/dev/nfs nfsroot=/nfs/nxs,hard,tcp,intr,v3 rw rootwait earlycon=uart8250 ,mmio32,0x68A10000 earlylog=0x8f110000,0x10000 console=ttyS0,115200n8 hugepages=0 cma=1G crashkernel =512M pci=pcie_bus_safe pciehp.pciehp_poll_mode=1 pciehp.pciehp_poll_time=5 vfio_pci.disable_idle_d3 =1 pcie_ports=native maxcpus=8 bgmac_platform.ethaddr=00:0A:F7:95:62:82 ip=10.136.13.31:10.136.4.15 1:10.136.13.1:255.255.255.0:::off loglevel=7 Kernel slot 2, dtb slot 1, rootfs slot 1 --- STARTING KERNEL EFI stub: Booting Linux Kernel... EFI stub: Using DTB from configuration table EFI stub: Exiting boot services and installing virtual address map... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.1.0 (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP Thu Nov 7 00:17:13 UTC 2019 [ 0.000000] Machine model: Stingray Combo SVK w/PAXB IOMMU (BCM958742K) [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000068a10000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.1.0 (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP Thu Nov 7 00:17:13 UTC 2019 [ 0.000000] Machine model: Stingray Combo SVK w/PAXB IOMMU (BCM958742K) [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000068a10000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] printk: bootconsole [earlycon_log0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: EFI v2.70 by EDK II [ 0.000000] efi: SMBIOS=0x85c90000 SMBIOS 3.0=0x85a20000 ACPI 2.0=0x85d50000 MEMATTR=0x89398018 MEMRESERVE=0x85f83018 [ 0.000000] crashkernel reserved: 0x00000000dfe00000 - 0x00000000ffe00000 (512 MB) [ 0.000000] cma: Reserved 1024 MiB at 0x000000009fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] random: get_random_bytes called from start_kernel+0xa4/0x448 with crng_init=0 [ 0.000000] percpu: Embedded 23 pages/cpu s53848 r8192 d32168 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 12376560 [ 0.000000] Kernel command line: FS2:\Image.2 root=/dev/nfs nfsroot=/nfs/nxs,hard,tcp,intr,v3 rw rootwait earlycon=uart8250,mmio32,0x68A10000 earlylog=0x8f110000,0x10000 console=ttyS0,115200n8 hugepages=0 cma=1G crashkernel=512M pci=pcie_bus_safe pciehp.pciehp_poll_mode=1 pciehp.pciehp_poll_time=5 vfio_pci.disable_idle_d3=1 pcie_ports=native maxcpus=8 bgmac_platform.ethaddr=00:0A:F7:95:62:82 ip=10.136.13.31:10.136.4.151:10.136.13.1:255.255.255.0:::off loglevel=7 [ 0.000000] Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes) [ 0.000000] Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes) [ 0.000000] software IO TLB: mapped [mem 0x9bc00000-0x9fc00000] (64MB) [ 0.000000] Memory: 47645776K/50292608K available (9532K kernel code, 742K rwdata, 3488K rodata, 960K init, 363K bss, 1598256K reserved, 1048576K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000063e00000 [ 0.000000] ITS [mem 0x63c20000-0x63c2ffff] [ 0.000000] ITS@0x0000000063c20000: allocated 32768 Devices @a3c3880000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x000000a3c3850000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000a3c3860000 [ 0.000000] arch_timer: cp15 timer(s) running at 125.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x39a85c4118, max_idle_ns: 881590405314 ns [ 0.000001] sched_clock: 56 bits at 125MHz, resolution 8ns, wraps every 4398046511100ns [ 0.009132] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 152900835740 ns [ 0.020032] Console: colour dummy device 80x25 [ 0.025066] printk: bootconsole [earlycon_log0] disabled [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.1.0 (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP Thu Nov 7 00:17:13 UTC 2019 [ 0.000000] Machine model: Stingray Combo SVK w/PAXB IOMMU (BCM958742K) [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000068a10000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] printk: bootconsole [earlycon_log0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: EFI v2.70 by EDK II [ 0.000000] efi: SMBIOS=0x85c90000 SMBIOS 3.0=0x85a20000 ACPI 2.0=0x85d50000 MEMATTR=0x89398018 MEMRESERVE=0x85f83018 [ 0.000000] crashkernel reserved: 0x00000000dfe00000 - 0x00000000ffe00000 (512 MB) [ 0.000000] cma: Reserved 1024 MiB at 0x000000009fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] random: get_random_bytes called from start_kernel+0xa4/0x448 with crng_init=0 [ 0.000000] percpu: Embedded 23 pages/cpu s53848 r8192 d32168 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 12376560 [ 0.000000] Kernel command line: FS2:\Image.2 root=/dev/nfs nfsroot=/nfs/nxs,hard,tcp,intr,v3 rw rootwait earlycon=uart8250,mmio32,0x68A10000 earlylog=0x8f110000,0x10000 console=ttyS0,115200n8 hugepages=0 cma=1G crashkernel=512M pci=pcie_bus_safe pciehp.pciehp_poll_mode=1 pciehp.pciehp_poll_time=5 vfio_pci.disable_idle_d3=1 pcie_ports=native maxcpus=8 bgmac_platform.ethaddr=00:0A:F7:95:62:82 ip=10.136.13.31:10.136.4.151:10.136.13.1:255.255.255.0:::off loglevel=7 [ 0.000000] Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes) [ 0.000000] Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes) [ 0.000000] software IO TLB: mapped [mem 0x9bc00000-0x9fc00000] (64MB) [ 0.000000] Memory: 47645776K/50292608K available (9532K kernel code, 742K rwdata, 3488K rodata, 960K init, 363K bss, 1598256K reserved, 1048576K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000063e00000 [ 0.000000] ITS [mem 0x63c20000-0x63c2ffff] [ 0.000000] ITS@0x0000000063c20000: allocated 32768 Devices @a3c3880000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x000000a3c3850000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000a3c3860000 [ 0.000000] arch_timer: cp15 timer(s) running at 125.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x39a85c4118, max_idle_ns: 881590405314 ns [ 0.000001] sched_clock: 56 bits at 125MHz, resolution 8ns, wraps every 4398046511100ns [ 0.009132] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 152900835740 ns [ 0.020032] Console: colour dummy device 80x25 [ 0.025066] printk: bootconsole [earlycon_log0] disabled [ 0.427284] printk: console [console_log0] enabled [ 0.432717] Calibrating delay loop (skipped), value calculated using timer frequency.. 250.00 BogoMIPS (lpj=500000) [ 0.444549] pid_max: default: 32768 minimum: 301 [ 0.449793] LSM: Security Framework initializing [ 0.455207] Mount-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.463369] Mountpoint-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.471990] *** VALIDATE proc *** [ 0.475793] *** VALIDATE cgroup1 *** [ 0.479842] *** VALIDATE cgroup2 *** [ 0.484076] ASID allocator initialised with 32768 entries [ 0.490212] rcu: Hierarchical SRCU implementation. [ 0.496067] Platform MSI: gic-its@63c20000 domain created [ 0.502216] PCI/MSI: /scr/interrupt-controller@2c00000/gic-its@63c20000 domain created [ 0.511235] Remapping and enabling EFI services. [ 0.516835] smp: Bringing up secondary CPUs ... I: Cluster #1 entering to snoop/dvm domain I: Cluster #2 entering to snoop/dvm domain I: Cluster #3 entering to snoop/dvm domain [ 0.522127] Detected PIPT I-cache on CPU1 [ 0.522140] GICv3: CPU1: found redistributor 1 region 0:0x0000000063e20000 [ 0.522146] GICv3: CPU1: using allocated LPI pending table @0x000000a3c3870000 [ 0.522158] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.522577] Detected PIPT I-cache on CPU2 [ 0.522588] GICv3: CPU2: found redistributor 100 region 0:0x0000000063e40000 [ 0.522597] GICv3: CPU2: using allocated LPI pending table @0x000000a3c38c0000 [ 0.522610] CPU2: Booted secondary processor 0x0000000100 [0x410fd083] [ 0.522793] Detected PIPT I-cache on CPU3 [ 0.522799] GICv3: CPU3: found redistributor 101 region 0:0x0000000063e60000 [ 0.522804] GICv3: CPU3: using allocated LPI pending table @0x000000a3c38d0000 [ 0.522812] CPU3: Booted secondary processor 0x0000000101 [0x410fd083] [ 0.524601] Detected PIPT I-cache on CPU4 [ 0.524610] GICv3: CPU4: found redistributor 200 region 0:0x0000000063e80000 [ 0.524618] GICv3: CPU4: using allocated LPI pending table @0x000000a3c38e0000 [ 0.524629] CPU4: Booted secondary processor 0x0000000200 [0x410fd083] [ 0.524812] Detected PIPT I-cache on CPU5 [ 0.524818] GICv3: CPU5: found redistributor 201 region 0:0x0000000063ea0000 [ 0.524823] GICv3: CPU5: using allocated LPI pending table @0x000000a3c38f0000 [ 0.524832] CPU5: Booted secondary processor 0x0000000201 [0x410fd083] [ 0.528543] Detected PIPT I-cache on CPU6 [ 0.528553] GICv3: CPU6: found redistributor 300 region 0:0x0000000063ec0000 [ 0.528560] GICv3: CPU6: using allocated LPI pending table @0x000000a3c3900000 [ 0.528572] CPU6: Booted secondary processor 0x0000000300 [0x410fd083] [ 0.528751] Detected PIPT I-cache on CPU7 [ 0.528757] GICv3: CPU7: found redistributor 301 region 0:0x0000000063ee0000 [ 0.528762] GICv3: CPU7: using allocated LPI pending table @0x000000a3c3910000 [ 0.528771] CPU7: Booted secondary processor 0x0000000301 [0x410fd083] [ 0.528799] smp: Brought up 1 node, 8 CPUs [ 0.735446] SMP: Total of 8 processors activated. [ 0.740773] CPU features: detected: 32-bit EL0 Support [ 0.746592] CPU features: detected: CRC32 instructions [ 0.752929] CPU: All CPU(s) started at EL2 [ 0.757583] alternatives: patching kernel code [ 0.762963] devtmpfs: initialized [ 0.768336] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.779389] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.793206] xor: measuring software checksum speed [ 0.838657] 8regs : 9090.000 MB/sec [ 0.883406] 32regs : 9449.000 MB/sec [ 0.928154] arm64_neon: 9022.000 MB/sec [ 0.932888] xor: using function: 32regs (9449.000 MB/sec) [ 0.939006] pinctrl core: initialized pinctrl subsystem [ 0.945274] SMBIOS 3.3.0 present. [ 0.949031] DMI: BRCM BRCM-SR/BRCM-SR, BIOS 0.1 Nov 4 2019 [ 0.955465] NET: Registered protocol family 16 [ 0.960667] audit: initializing netlink subsys (disabled) [ 0.966825] audit: type=2000 audit(0.580:1): state=initialized audit_enabled=0 res=1 [ 0.975614] cpuidle: using governor menu [ 0.980141] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____)) [ 0.988525] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.996520] DMA: preallocated 256 KiB pool for atomic allocations [ 1.005641] brcm,iproc-mailbox 66424024.mailbox: Initializing iproc mailbox controller [ 1.015451] iproc-idm 8f130000.idm-elog: iProc IDM ELOG registered [ 1.022580] iProc IDM device idm-paxb0-axi registered [ 1.028411] iProc IDM device idm-paxb1-axi registered [ 1.034240] iProc IDM device idm-paxb2-axi registered [ 1.040071] iProc IDM device idm-paxb3-axi registered [ 1.045908] iProc IDM device idm-pcie-axi registered [ 1.051638] iProc IDM device idm-paxb4-axi registered [ 1.057467] iProc IDM device idm-paxb5-axi registered [ 1.063294] iProc IDM device idm-paxb6-axi registered [ 1.069123] iProc IDM device idm-paxb7-axi registered [ 1.074952] iProc IDM device idm-mhb-nitro-axi registered [ 1.081170] iProc IDM device idm-mhb-pcie-axi registered [ 1.087296] iProc IDM device idm-mhb-ep-apb registered [ 1.093224] iProc IDM device idm-mhb-paxc-axi registered [ 1.099348] iProc IDM device idm-mhb-apb registered [ 1.104979] iProc IDM device idm-mhb-paxc-apb registered [ 1.111105] iProc IDM device idm-scr-pcie0 registered [ 1.116934] iProc IDM device idm-scr-pcie1 registered [ 1.122768] iProc IDM device idm-scr-paxc registered [ 1.128500] iProc IDM device idm-scr-fs registered [ 1.134032] iProc IDM device idm-scr-hsls registered [ 1.139764] iProc IDM device idm-scr-crmu registered [ 1.145494] iProc IDM device idm-scr-usb registered [ 1.151124] iProc IDM device idm-scr-axi2apb-div4 registered [ 1.157652] iProc IDM device idm-scr-axi2apb-div4-eme registered [ 1.164567] iProc IDM device idm-scr-axi2apb-cssys registered [ 1.171188] iProc IDM device idm-scr-smmu registered [ 1.176918] iProc IDM device idm-scr-gic500 registered [ 1.182847] iProc IDM device idm-scr-sata registered [ 1.188579] iProc IDM device idm-scr-cssys-stm-axi registered [ 1.195198] iProc IDM device idm-scr-ds0 registered [ 1.202535] gpiochip_add_data_with_key: GPIOs 355..505 (689d0000.gpio) failed to register, -517 [ 1.212399] iproc-gpio 689d0000.gpio: unable to add GPIO chip [ 1.226476] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 1.234076] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 1.241669] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 1.249262] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 1.256986] cryptd: max_cpu_qlen set to 1000 [ 1.329849] raid6: neonx8 gen() 6792 MB/s [ 1.402713] raid6: neonx8 xor() 5873 MB/s [ 1.475578] raid6: neonx4 gen() 6676 MB/s [ 1.548440] raid6: neonx4 xor() 5163 MB/s [ 1.621305] raid6: neonx2 gen() 5500 MB/s [ 1.694168] raid6: neonx2 xor() 5330 MB/s [ 1.767033] raid6: neonx1 gen() 3581 MB/s [ 1.839899] raid6: neonx1 xor() 3544 MB/s [ 1.912763] raid6: int64x8 gen() 3807 MB/s [ 1.985628] raid6: int64x8 xor() 2513 MB/s [ 2.058493] raid6: int64x4 gen() 3804 MB/s [ 2.131361] raid6: int64x4 xor() 2676 MB/s [ 2.204227] raid6: int64x2 gen() 2846 MB/s [ 2.277098] raid6: int64x2 xor() 2510 MB/s [ 2.349965] raid6: int64x1 gen() 1812 MB/s [ 2.422835] raid6: int64x1 xor() 1555 MB/s [ 2.427669] raid6: using algorithm neonx8 gen() 6792 MB/s [ 2.433782] raid6: .... xor() 5873 MB/s, rmw enabled [ 2.439404] raid6: using neon recovery algorithm [ 2.444975] vgaarb: loaded [ 2.448099] SCSI subsystem initialized [ 2.452424] ssp-pl022 68a80000.spi: ARM PL022 driver, device ID: 0x00241022 [ 2.460338] ssp-pl022 68a90000.spi: ARM PL022 driver, device ID: 0x00241022 [ 2.468287] usbcore: registered new interface driver usbfs [ 2.474510] usbcore: registered new interface driver hub [ 2.480549] usbcore: registered new device driver usb [ 2.486291] pps_core: LinuxPPS API ver. 1 registered [ 2.491913] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.502269] PTP clock support registered [ 2.506764] EDAC MC: Ver: 3.0.0 [ 2.510398] Registered efivars operations [ 2.515214] clocksource: Switched to clocksource arch_sys_counter [ 2.522170] VFS: Disk quotas dquot_6.6.0 [ 2.526625] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.534426] *** VALIDATE hugetlbfs *** [ 2.540486] NET: Registered protocol family 2 [ 2.545550] tcp_listen_portaddr_hash hash table entries: 32768 (order: 7, 524288 bytes) [ 2.554837] TCP established hash table entries: 524288 (order: 10, 4194304 bytes) [ 2.564374] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 2.572244] TCP: Hash tables configured (established 524288 bind 65536) [ 2.579788] UDP hash table entries: 32768 (order: 8, 1048576 bytes) [ 2.587291] UDP-Lite hash table entries: 32768 (order: 8, 1048576 bytes) [ 2.595320] NET: Registered protocol family 1 [ 2.600384] RPC: Registered named UNIX socket transport module. [ 2.607094] RPC: Registered udp transport module. [ 2.612420] RPC: Registered tcp transport module. [ 2.617747] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.625402] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 2.634354] kvm [1]: IPA Size Limit: 44bits [ 2.639265] kvm [1]: GICv3: no GICV resource entry [ 2.644692] kvm [1]: disabling GICv2 emulation [ 2.649734] kvm [1]: GIC system register CPU interface enabled [ 2.656398] kvm [1]: vgic interrupt IRQ1 [ 2.660913] kvm [1]: Hyp mode initialized successfully [ 2.675519] workingset: timestamp_bits=46 max_order=24 bucket_order=0 [ 2.684711] NFS: Registering the id_resolver key type [ 2.690439] Key type id_resolver registered [ 2.695173] Key type id_legacy registered [ 2.699713] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.707347] 9p: Installing v9fs 9p2000 file system support [ 2.717536] alg: No test for lzo-rle (lzo-rle-generic) [ 2.723566] alg: No test for lzo-rle (lzo-rle-scomp) [ 2.733057] NET: Registered protocol family 38 [ 2.738094] async_tx: api initialized (async) [ 2.743041] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 2.751424] io scheduler mq-deadline registered [ 2.756553] io scheduler kyber registered [ 2.761428] brcm-sata-phy 67d02100.sata_phy: registered 1 port(s) [ 2.768411] brcm-sata-phy 67d12100.sata_phy: registered 1 port(s) [ 2.775361] brcm-sata-phy 67d22100.sata_phy: registered 1 port(s) [ 2.782311] brcm-sata-phy 67d32100.sata_phy: registered 1 port(s) [ 2.789263] brcm-sata-phy 67e02100.sata_phy: registered 1 port(s) [ 2.796213] brcm-sata-phy 67e12100.sata_phy: registered 1 port(s) [ 2.803163] brcm-sata-phy 67e22100.sata_phy: registered 1 port(s) [ 2.810113] brcm-sata-phy 67e32100.sata_phy: registered 1 port(s) [ 2.817205] sr-pcie-phy 40000000.phy: Stingray PCIe PHY driver initialized [ 2.825273] pinctrl-single 68a40000.pinconf: please update dts to use #pinctrl-cells = <1> [ 2.834707] pinctrl-single 68a40000.pinconf: 148 pins, size 592 [ 2.841445] pinctrl-single 68a4029c.pinmux: please update dts to use #pinctrl-cells = <1> [ 2.850781] pinctrl-single 68a4029c.pinmux: 155 pins, size 620 [ 2.857620] iproc-pcie 48000000.pcie: host bridge /pcie@48000000 ranges: [ 2.865223] iproc-pcie 48000000.pcie: MEM 0x400000000..0x46fffffff -> 0x400000000 [ 2.873902] iproc-pcie 48000000.pcie: MEM 0x470000000..0x47fffffff -> 0x40000000 [ 2.882484] iproc-pcie 48000000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 2.999250] iproc-pcie 48000000.pcie: link UP @ Speed Gen-3 and width-x4 [ 3.006882] iproc-pcie 48000000.pcie: not using iProc MSI [ 3.013028] iproc-pcie 48000000.pcie: PCI host bridge to bus 0000:00 [ 3.020223] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.026437] pci_bus 0000:00: root bus resource [mem 0x400000000-0x46fffffff pref] [ 3.034918] pci_bus 0000:00: root bus resource [mem 0x470000000-0x47fffffff] (bus address [0x40000000-0x4fffffff]) [ 3.047320] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.057773] pci 0000:01:00.0: enabling Extended Tags [ 3.064580] pci 0000:00:00.0: BAR 14: assigned [mem 0x470000000-0x4700fffff] [ 3.072570] pci 0000:01:00.0: BAR 6: assigned [mem 0x470000000-0x47001ffff pref] [ 3.080952] pci 0000:01:00.0: BAR 4: assigned [mem 0x470020000-0x47002ffff 64bit] [ 3.089612] pci 0000:01:00.0: BAR 0: assigned [mem 0x470030000-0x470033fff 64bit] [ 3.098213] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.103838] pci 0000:00:00.0: bridge window [mem 0x470000000-0x4700fffff] [ 3.111734] pci 0000:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 3.121340] pci 0000:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512 [ 3.130962] iproc-pcie 48004000.pcie: host bridge /pcie@48004000 ranges: [ 3.138563] iproc-pcie 48004000.pcie: MEM 0x480000000..0x4efffffff -> 0x480000000 [ 3.147243] iproc-pcie 48004000.pcie: MEM 0x4f0000000..0x4ffffffff -> 0x40000000 [ 3.155824] iproc-pcie 48004000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 3.275248] iproc-pcie 48004000.pcie: link UP @ Speed Gen-3 and width-x4 [ 3.282868] iproc-pcie 48004000.pcie: not using iProc MSI [ 3.289005] iproc-pcie 48004000.pcie: PCI host bridge to bus 0001:00 [ 3.296207] pci_bus 0001:00: root bus resource [bus 00-ff] [ 3.302421] pci_bus 0001:00: root bus resource [mem 0x480000000-0x4efffffff pref] [ 3.310907] pci_bus 0001:00: root bus resource [mem 0x4f0000000-0x4ffffffff] (bus address [0x40000000-0x4fffffff]) [ 3.323270] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.333712] pci 0001:01:00.0: enabling Extended Tags [ 3.351768] pci 0001:00:00.0: BAR 14: assigned [mem 0x4f0000000-0x4f00fffff] [ 3.359758] pci 0001:01:00.0: BAR 6: assigned [mem 0x4f0000000-0x4f001ffff pref] [ 3.368141] pci 0001:01:00.0: BAR 4: assigned [mem 0x4f0020000-0x4f002ffff 64bit] [ 3.376800] pci 0001:01:00.0: BAR 0: assigned [mem 0x4f0030000-0x4f0033fff 64bit] [ 3.385399] pci 0001:00:00.0: PCI bridge to [bus 01] [ 3.391023] pci 0001:00:00.0: bridge window [mem 0x4f0000000-0x4f00fffff] [ 3.398919] pci 0001:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 3.408525] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512 [ 3.418141] iproc-pcie 48008000.pcie: host bridge /pcie@48008000 ranges: [ 3.425741] iproc-pcie 48008000.pcie: MEM 0x500000000..0x56fffffff -> 0x500000000 [ 3.434422] iproc-pcie 48008000.pcie: MEM 0x570000000..0x57fffffff -> 0x40000000 [ 3.443001] iproc-pcie 48008000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 3.454242] phy phy-40000000.phy.10: phy init failed --> -19 [ 3.460653] iproc-pcie 48008000.pcie: unable to initialize PCIe PHY [ 3.467752] iproc-pcie 48008000.pcie: PCIe controller setup failed [ 3.474774] iproc-pcie 4800c000.pcie: host bridge /pcie@4800c000 ranges: [ 3.482375] iproc-pcie 4800c000.pcie: MEM 0x580000000..0x5efffffff -> 0x580000000 [ 3.491055] iproc-pcie 4800c000.pcie: MEM 0x5f0000000..0x5ffffffff -> 0x40000000 [ 3.499634] iproc-pcie 4800c000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 3.510875] phy phy-40000000.phy.11: phy init failed --> -19 [ 3.517285] iproc-pcie 4800c000.pcie: unable to initialize PCIe PHY [ 3.524385] iproc-pcie 4800c000.pcie: PCIe controller setup failed [ 3.531405] iproc-pcie 48010000.pcie: host bridge /pcie@48010000 ranges: [ 3.539003] iproc-pcie 48010000.pcie: MEM 0x600000000..0x66fffffff -> 0x600000000 [ 3.547682] iproc-pcie 48010000.pcie: MEM 0x670000000..0x67fffffff -> 0x40000000 [ 3.556261] iproc-pcie 48010000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 3.567502] phy phy-40000000.phy.12: phy init failed --> -19 [ 3.573911] iproc-pcie 48010000.pcie: unable to initialize PCIe PHY [ 3.581011] iproc-pcie 48010000.pcie: PCIe controller setup failed [ 3.588032] iproc-pcie 48014000.pcie: host bridge /pcie@48014000 ranges: [ 3.595632] iproc-pcie 48014000.pcie: MEM 0x680000000..0x6efffffff -> 0x680000000 [ 3.604312] iproc-pcie 48014000.pcie: MEM 0x6f0000000..0x6ffffffff -> 0x40000000 [ 3.612891] iproc-pcie 48014000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 3.624132] phy phy-40000000.phy.13: phy init failed --> -19 [ 3.630542] iproc-pcie 48014000.pcie: unable to initialize PCIe PHY [ 3.637642] iproc-pcie 48014000.pcie: PCIe controller setup failed [ 3.644662] iproc-pcie 48018000.pcie: host bridge /pcie@48018000 ranges: [ 3.652262] iproc-pcie 48018000.pcie: MEM 0x700000000..0x76fffffff -> 0x700000000 [ 3.660941] iproc-pcie 48018000.pcie: MEM 0x770000000..0x77fffffff -> 0x40000000 [ 3.669519] iproc-pcie 48018000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 3.787248] iproc-pcie 48018000.pcie: link UP @ Speed Gen-3 and width-x4 [ 3.794867] iproc-pcie 48018000.pcie: not using iProc MSI [ 3.801006] iproc-pcie 48018000.pcie: PCI host bridge to bus 0006:00 [ 3.808208] pci_bus 0006:00: root bus resource [bus 00-ff] [ 3.814422] pci_bus 0006:00: root bus resource [mem 0x700000000-0x76fffffff pref] [ 3.822902] pci_bus 0006:00: root bus resource [mem 0x770000000-0x77fffffff] (bus address [0x40000000-0x4fffffff]) [ 3.835262] pci 0006:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.845706] pci 0006:01:00.0: enabling Extended Tags [ 3.852502] pci 0006:00:00.0: BAR 14: assigned [mem 0x770000000-0x7700fffff] [ 3.860491] pci 0006:01:00.0: BAR 6: assigned [mem 0x770000000-0x77001ffff pref] [ 3.868874] pci 0006:01:00.0: BAR 4: assigned [mem 0x770020000-0x77002ffff 64bit] [ 3.877532] pci 0006:01:00.0: BAR 0: assigned [mem 0x770030000-0x770033fff 64bit] [ 3.886134] pci 0006:00:00.0: PCI bridge to [bus 01] [ 3.891758] pci 0006:00:00.0: bridge window [mem 0x770000000-0x7700fffff] [ 3.899653] pci 0006:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 3.909259] pci 0006:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512 [ 3.918877] iproc-pcie 4801c000.pcie: host bridge /pcie@4801c000 ranges: [ 3.926477] iproc-pcie 4801c000.pcie: MEM 0x780000000..0x7dfffffff -> 0x780000000 [ 3.935157] iproc-pcie 4801c000.pcie: MEM 0x7e0000000..0x7efffffff -> 0x7d0000000 [ 3.943837] iproc-pcie 4801c000.pcie: MEM 0x7f0000000..0x7ffffffff -> 0x40000000 [ 3.952417] iproc-pcie 4801c000.pcie: reads of config registers that contain 0xffff0001 return incorrect data [ 4.071248] iproc-pcie 4801c000.pcie: link UP @ Speed Gen-3 and width-x4 [ 4.078867] iproc-pcie 4801c000.pcie: not using iProc MSI [ 4.085004] iproc-pcie 4801c000.pcie: PCI host bridge to bus 0007:00 [ 4.092207] pci_bus 0007:00: root bus resource [bus 00-ff] [ 4.098420] pci_bus 0007:00: root bus resource [mem 0x780000000-0x7dfffffff pref] [ 4.106901] pci_bus 0007:00: root bus resource [mem 0x7e0000000-0x7efffffff pref] (bus address [0x7d0000000-0x7dfffffff]) [ 4.119325] pci_bus 0007:00: root bus resource [mem 0x7f0000000-0x7ffffffff] (bus address [0x40000000-0x4fffffff]) [ 4.131682] pci 0007:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.142138] pci 0007:01:00.0: enabling Extended Tags [ 4.148938] pci 0007:00:00.0: BAR 14: assigned [mem 0x7f0000000-0x7f00fffff] [ 4.156929] pci 0007:01:00.0: BAR 6: assigned [mem 0x7f0000000-0x7f001ffff pref] [ 4.165313] pci 0007:01:00.0: BAR 4: assigned [mem 0x7f0020000-0x7f002ffff 64bit] [ 4.173972] pci 0007:01:00.0: BAR 0: assigned [mem 0x7f0030000-0x7f0033fff 64bit] [ 4.182574] pci 0007:00:00.0: PCI bridge to [bus 01] [ 4.188199] pci 0007:00:00.0: bridge window [mem 0x7f0000000-0x7f00fffff] [ 4.196096] pci 0007:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 4.205704] pci 0007:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512 [ 4.215305] iproc-pcie 60400000.pcie: host bridge /pcie@60400000 ranges: [ 4.222902] iproc-pcie 60400000.pcie: MEM 0x10000000..0x2fffffff -> 0x10000000 [ 4.231295] iproc-pcie 60400000.pcie: not using iProc MSI [ 4.237434] iproc-pcie 60400000.pcie: PCI host bridge to bus 0008:00 [ 4.244634] pci_bus 0008:00: root bus resource [bus 00-01] [ 4.250848] pci_bus 0008:00: root bus resource [mem 0x10000000-0x2fffffff] [ 4.258722] OF: /pcie@60400000: Invalid msi-map translation - no match for rid 0x0 on (null) [ 4.270690] pci 0008:00:00.0: BAR 14: assigned [mem 0x10000000-0x100fffff] [ 4.278482] pci 0008:00:00.0: BAR 15: assigned [mem 0x10100000-0x103fffff 64bit pref] [ 4.287360] pci 0008:01:00.0: BAR 2: assigned [mem 0x10100000-0x101fffff 64bit pref] [ 4.296145] pci 0008:01:00.1: BAR 2: assigned [mem 0x10200000-0x102fffff 64bit pref] [ 4.304928] pci 0008:01:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit] [ 4.313219] pci 0008:01:00.1: BAR 0: assigned [mem 0x10010000-0x1001ffff 64bit] [ 4.321510] pci 0008:01:00.0: BAR 4: assigned [mem 0x10300000-0x10300fff 64bit pref] [ 4.330294] pci 0008:01:00.1: BAR 4: assigned [mem 0x10301000-0x10301fff 64bit pref] [ 4.339077] pci 0008:00:00.0: PCI bridge to [bus 01] [ 4.344703] pci 0008:00:00.0: bridge window [mem 0x10000000-0x100fffff] [ 4.352398] pci 0008:00:00.0: bridge window [mem 0x10100000-0x103fffff 64bit pref] [ 4.361194] pci 0008:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 4.370774] pci 0008:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 4.380343] pci 0008:01:00.1: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 4.391727] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 4.399370] printk: console [ttyS0] disabled [ 4.404214] 68a10000.uart: ttyS0 at MMIO 0x68a10000 (irq = 117, base_baud = 1562500) is a 16550A [ 4.414184] printk: console [ttyS0] enabled [ 4.414184] printk: console [ttyS0] enabled [ 4.423231] printk: bootconsole [uart8250] disabled [ 4.423231] printk: bootconsole [uart8250] disabled [ 4.433885] 68a20000.uart: ttyS2 at MMIO 0x68a20000 (irq = 118, base_baud = 1562500) is a 16550A [ 4.443050] 68a30000.uart: ttyS3 at MMIO 0x68a30000 (irq = 119, base_baud = 1562500) is a 16550A [ 4.452434] iproc-rng200 68b20000.hwrng: hwrng registered [ 4.458219] arm-smmu 64000000.mmu: probing hardware configuration... [ 4.464777] arm-smmu 64000000.mmu: SMMUv2 with: [ 4.469452] arm-smmu 64000000.mmu: stage 1 translation [ 4.474842] arm-smmu 64000000.mmu: stage 2 translation [ 4.480233] arm-smmu 64000000.mmu: nested translation [ 4.485535] arm-smmu 64000000.mmu: stream matching with 55 register groups [ 4.492719] arm-smmu 64000000.mmu: 62 context banks (0 stage-2 only) [ 4.499366] arm-smmu 64000000.mmu: Supported page sizes: 0x61311000 [ 4.505922] arm-smmu 64000000.mmu: Stage-1: 48-bit VA -> 48-bit IPA [ 4.512478] arm-smmu 64000000.mmu: Stage-2: 48-bit IPA -> 48-bit PA [ 4.521533] loop: module loaded [ 4.524940] Loading iSCSI transport class v2.0-870. [ 4.530092] iscsi: registered transport (tcp) [ 4.534589] mpt3sas version 27.102.00.00 loaded [ 4.539533] nvme 0000:01:00.0: Adding to iommu group 0 [ 4.545049] nvme nvme0: pci function 0000:01:00.0 [ 4.549922] pci 0000:00:00.0: enabling device (0000 -> 0002) [ 4.549947] nvme 0001:01:00.0: Adding to iommu group 1 [ 4.561093] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 4.567157] nvme nvme1: pci function 0001:01:00.0 [ 4.573633] pci 0001:00:00.0: enabling device (0000 -> 0002) [ 4.573647] nvme 0006:01:00.0: Adding to iommu group 2 [ 4.584805] nvme 0001:01:00.0: enabling device (0000 -> 0002) [ 4.590868] nvme nvme2: pci function 0006:01:00.0 [ 4.597424] pci 0006:00:00.0: enabling device (0000 -> 0002) [ 4.597427] nvme 0007:01:00.0: Adding to iommu group 3 [ 4.608596] nvme 0006:01:00.0: enabling device (0000 -> 0002) [ 4.614660] nvme nvme3: pci function 0007:01:00.0 [ 4.621154] pci 0007:00:00.0: enabling device (0000 -> 0002) [ 4.621342] ahci 67d00000.ahci: masking port_map 0x1 -> 0x1 [ 4.632750] ahci 67d00000.ahci: SSS flag set, parallel bus scan disabled [ 4.632774] nvme 0007:01:00.0: enabling device (0000 -> 0002) [ 4.649751] ahci 67d00000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.658552] ahci 67d00000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.666523] scsi host0: ahci [ 4.669600] ata1: SATA max UDMA/133 mmio [mem 0x67d00000-0x67d00fff] port 0x100 irq 101 [ 4.677974] ahci 67d10000.ahci: masking port_map 0x1 -> 0x1 [ 4.683729] ahci 67d10000.ahci: SSS flag set, parallel bus scan disabled [ 4.700706] ahci 67d10000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.709503] ahci 67d10000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.717429] scsi host1: ahci [ 4.720470] ata2: SATA max UDMA/133 mmio [mem 0x67d10000-0x67d10fff] port 0x100 irq 102 [ 4.728841] ahci 67d20000.ahci: masking port_map 0x1 -> 0x1 [ 4.734597] ahci 67d20000.ahci: SSS flag set, parallel bus scan disabled [ 4.751574] ahci 67d20000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.760371] ahci 67d20000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.768326] scsi host2: ahci [ 4.771366] ata3: SATA max UDMA/133 mmio [mem 0x67d20000-0x67d20fff] port 0x100 irq 103 [ 4.779737] ahci 67d30000.ahci: masking port_map 0x1 -> 0x1 [ 4.785493] ahci 67d30000.ahci: SSS flag set, parallel bus scan disabled [ 4.802471] ahci 67d30000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.811269] ahci 67d30000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.819196] scsi host3: ahci [ 4.822243] ata4: SATA max UDMA/133 mmio [mem 0x67d30000-0x67d30fff] port 0x100 irq 104 [ 4.830615] ahci 67e00000.ahci: masking port_map 0x1 -> 0x1 [ 4.836370] ahci 67e00000.ahci: SSS flag set, parallel bus scan disabled [ 4.853346] ahci 67e00000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.862144] ahci 67e00000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.870076] scsi host4: ahci [ 4.873118] ata5: SATA max UDMA/133 mmio [mem 0x67e00000-0x67e00fff] port 0x100 irq 105 [ 4.881492] ahci 67e10000.ahci: masking port_map 0x1 -> 0x1 [ 4.887247] ahci 67e10000.ahci: SSS flag set, parallel bus scan disabled [ 4.904224] ahci 67e10000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.913021] ahci 67e10000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.920960] scsi host5: ahci [ 4.924001] ata6: SATA max UDMA/133 mmio [mem 0x67e10000-0x67e10fff] port 0x100 irq 106 [ 4.932373] ahci 67e20000.ahci: masking port_map 0x1 -> 0x1 [ 4.938128] ahci 67e20000.ahci: SSS flag set, parallel bus scan disabled [ 4.955104] ahci 67e20000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.963903] ahci 67e20000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 4.971877] scsi host6: ahci [ 4.974914] ata7: SATA max UDMA/133 mmio [mem 0x67e20000-0x67e20fff] port 0x100 irq 107 [ 4.983289] ahci 67e30000.ahci: masking port_map 0x1 -> 0x1 [ 4.989044] ahci 67e30000.ahci: SSS flag set, parallel bus scan disabled [ 4.993337] ata1: SATA link down (SStatus 0 SControl 300) [ 5.006021] ahci 67e30000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.014818] ahci 67e30000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 5.022751] scsi host7: ahci [ 5.025792] ata8: SATA max UDMA/133 mmio [mem 0x67e30000-0x67e30fff] port 0x100 irq 108 [ 5.034502] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xc3 [ 5.041060] nand: Micron MT29F8G16ABACAWP [ 5.041331] ata2: SATA link down (SStatus 0 SControl 300) [ 5.045197] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 [ 5.045203] iproc_nand 68c60000.nand: detected 1024MiB total, 256KiB blocks, 4KiB pages, 16B OOB, 16-bit, BCH-8 [ 5.069167] Scanning device for bad blocks [ 5.089318] random: fast init done [ 5.093330] ata3: SATA link down (SStatus 0 SControl 300) [ 5.144390] ata4: SATA link down (SStatus 0 SControl 300) [ 5.198953] ata5: SATA link down (SStatus 0 SControl 300) [ 5.245340] ata6: SATA link down (SStatus 0 SControl 300) [ 5.297336] ata7: SATA link down (SStatus 0 SControl 300) [ 5.348397] ata8: SATA link down (SStatus 0 SControl 300) [ 5.820025] random: crng init done [ 6.894772] libphy: iProc MDIO mux bus: probed [ 6.899376] libphy: mdio_mux: probed [ 6.903079] libphy: mdio_mux: probed [ 6.910852] mdio-mux-iproc 68920000.mdio-mux: iProc mdiomux registered [ 6.917749] libphy: Fixed MDIO Bus: probed [ 6.921977] tun: Universal TUN/TAP device driver, 1.6 [ 6.953370] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 6.959390] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 6.965530] usbcore: registered new interface driver r8152 [ 6.971203] usbcore: registered new interface driver asix [ 6.976788] usbcore: registered new interface driver ax88179_178a [ 6.983082] usbcore: registered new interface driver cdc_ether [ 6.989108] usbcore: registered new interface driver net1080 [ 6.994955] usbcore: registered new interface driver cdc_subset [ 7.002778] usbcore: registered new interface driver zaurus [ 7.003344] nvme nvme0: 8/0/0 default/read/poll queues [ 7.008538] usbcore: registered new interface driver cdc_ncm [ 7.019848] VFIO - User Level meta-driver version: 0.3 [ 7.025229] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.031975] ehci-pci: EHCI PCI platform driver [ 7.036578] ehci-platform: EHCI generic platform driver [ 7.042047] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.048425] ohci-pci: OHCI PCI platform driver [ 7.053019] ohci-platform: OHCI generic platform driver [ 7.175218] xhci-hcd 68501000.usb: xHCI Host Controller [ 7.180615] xhci-hcd 68501000.usb: new USB bus registered, assigned bus number 1 [ 7.188449] xhci-hcd 68501000.usb: hcc params 0x0250f16d hci version 0x100 quirks 0x0000001000010010 [ 7.197888] xhci-hcd 68501000.usb: irq 109, io mem 0x68501000 [ 7.204039] hub 1-0:1.0: USB hub found [ 7.207917] hub 1-0:1.0: 2 ports detected [ 7.212143] xhci-hcd 68501000.usb: xHCI Host Controller [ 7.217537] xhci-hcd 68501000.usb: new USB bus registered, assigned bus number 2 [ 7.225171] xhci-hcd 68501000.usb: Host supports USB 3.0 SuperSpeed [ 7.231739] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 7.240194] hub 2-0:1.0: USB hub found [ 7.244068] hub 2-0:1.0: 1 port detected [ 7.259847] nvme nvme2: 8/0/0 default/read/poll queues [ 7.259862] nvme nvme1: 8/0/0 default/read/poll queues [ 7.259898] nvme nvme3: 8/0/0 default/read/poll queues [ 7.447216] xhci-hcd 68511000.usb: xHCI Host Controller [ 7.452612] xhci-hcd 68511000.usb: new USB bus registered, assigned bus number 3 [ 7.460428] xhci-hcd 68511000.usb: hcc params 0x0250f16d hci version 0x100 quirks 0x0000001000010010 [ 7.469865] xhci-hcd 68511000.usb: irq 111, io mem 0x68511000 [ 7.475974] hub 3-0:1.0: USB hub found [ 7.479849] hub 3-0:1.0: 2 ports detected [ 7.484061] xhci-hcd 68511000.usb: xHCI Host Controller [ 7.489455] xhci-hcd 68511000.usb: new USB bus registered, assigned bus number 4 [ 7.497087] xhci-hcd 68511000.usb: Host supports USB 3.0 SuperSpeed [ 7.503654] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 7.512105] hub 4-0:1.0: USB hub found [ 7.515980] hub 4-0:1.0: 1 port detected [ 7.520160] usbcore: registered new interface driver cdc_acm [ 7.526000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 7.534280] usbcore: registered new interface driver usb-storage [ 7.540502] usbcore: registered new interface driver ftdi_sio [ 7.546438] usbserial: USB Serial support registered for FTDI USB Serial Device [ 7.554007] usbcore: registered new interface driver pl2303 [ 7.559764] usbserial: USB Serial support registered for pl2303 [ 7.566089] bdc 68502000.usb: Clock not found in Device Tree [ 7.571943] bdc 68502000.usb: Using 2 phy(s) [ 7.576475] bdc 68521000.usb: Clock not found in Device Tree [ 7.582326] bdc 68521000.usb: Using 1 phy(s) [ 7.586902] iproc-rtc rtc: bbl is not powered up:-1 [ 7.591974] i2c /dev entries driver [ 7.595740] bcm-iproc-i2c 689b0000.i2c: bus set to 100000 Hz [ 7.601805] bcm-iproc-i2c 689e0000.i2c: bus set to 100000 Hz [ 7.607983] pcf857x 1-0027: probed [ 7.611966] sp805-wdt 689c0000.watchdog: registration successful [ 7.618302] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 7.627131] sdhci: Secure Digital Host Controller Interface driver [ 7.633509] sdhci: Copyright(c) Pierre Ossman [ 7.638004] sdhci-pltfm: SDHCI platform and OF driver helper [ 7.643928] sdhci-iproc 68cf1000.sdhci: Adding to iommu group 4 [ 7.650166] sdhci-iproc 68cf2000.sdhci: Adding to iommu group 5 [ 7.656381] EFI Variables Facility v0.08 2004-May-17 [ 7.664210] usbcore: registered new interface driver usbhid [ 7.669961] usbhid: USB HID core driver [ 7.674002] NET: Registered protocol family 40 [ 7.678809] arm-ccn 61000000.ccn: No access to interrupts, using timer. [ 7.685902] GACT probability on [ 7.689148] Mirror/redirect action on [ 7.692932] Simple TC action Loaded [ 7.696537] u32 classifier [ 7.699329] Performance counters on [ 7.703285] input device check on [ 7.707061] Actions configured [ 7.710615] NET: Registered protocol family 17 [ 7.715249] 9pnet: Installing 9P2000 support [ 7.719672] Key type dns_resolver registered [ 7.724310] registered taskstats version 1 [ 7.729902] ssp-pl022 68a80000.spi: ARM PL022 driver, device ID: 0x00241022 [ 7.737111] ssp-pl022 68a80000.spi: mapped registers from 0x0000000068a80000 to 000000009c395184 [ 7.746194] ssp-pl022 68a80000.spi: Failed to work in dma mode, work without dma! [ 7.754043] ssp-pl022 68a90000.spi: ARM PL022 driver, device ID: 0x00241022 [ 7.761246] ssp-pl022 68a90000.spi: mapped registers from 0x0000000068a90000 to 000000000a741b16 [ 7.770321] ssp-pl022 68a90000.spi: Failed to work in dma mode, work without dma! [ 7.778196] pcieport 0000:00:00.0: Adding to iommu group 6 [ 7.783975] pcieport 0000:00:00.0: Signaling PME with IRQ 140 [ 7.789969] aer 0000:00:00.0:pcie002: AER enabled with IRQ 140 [ 7.796070] pcieport 0001:00:00.0: Adding to iommu group 7 [ 7.801835] pcieport 0001:00:00.0: Signaling PME with IRQ 141 [ 7.807824] aer 0001:00:00.0:pcie002: AER enabled with IRQ 141 [ 7.813923] pcieport 0006:00:00.0: Adding to iommu group 8 [ 7.819678] pcieport 0006:00:00.0: Signaling PME with IRQ 143 [ 7.825663] aer 0006:00:00.0:pcie002: AER enabled with IRQ 143 [ 7.831761] pcieport 0007:00:00.0: Adding to iommu group 9 [ 7.837517] pcieport 0007:00:00.0: Signaling PME with IRQ 145 [ 7.843504] aer 0007:00:00.0:pcie002: AER enabled with IRQ 145 [ 7.849597] dma-pl330 68c10000.dma: Adding to iommu group 10 [ 7.855959] dma-pl330 68c10000.dma: Loaded driver for PL330 DMAC-241330 [ 7.862786] dma-pl330 68c10000.dma: DBUFF-1024x8bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 7.871540] pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator [ 7.881820] pca953x 0-0020: interrupt support not compiled in [ 7.920740] mmc0: SDHCI controller on 68cf1000.sdhci [68cf1000.sdhci] using ADMA [ 7.957698] mmc1: SDHCI controller on 68cf2000.sdhci [68cf2000.sdhci] using ADMA [ 7.965441] hctosys: unable to open rtc device (rtc0) [ 8.003108] bgmac-enet 68c40000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 8.005539] mmc0: new DDR MMC card at address 0001 [ 8.016977] mmcblk0: mmc0:0001 MMC16G 14.6 GiB [ 8.021873] mmcblk0boot0: mmc0:0001 MMC16G partition 1 4.00 MiB [ 8.028205] mmcblk0boot1: mmc0:0001 MMC16G partition 2 4.00 MiB [ 8.031217] IP-Config: Complete: [ 8.034366] mmcblk0rpmb: mmc0:0001 MMC16G partition 3 128 KiB, chardev (243:0) [ 8.037642] device=eth0, hwaddr=00:0a:f7:95:62:82, ipaddr=10.136.13.31, mask=255.255.255.0, gw=10.136.13.1 [ 8.037644] host=10.136.13.31, domain=, nis-domain=(none) [ 8.037646] bootserver=10.136.4.151, rootserver=10.136.4.151, rootpath= [ 8.054501] mmcblk0: p1 p2 p3 p4 p5 [ 8.072682] ttyS0 - failed to request DMA [ 8.076847] md: Waiting for all devices to be available before autodetect [ 8.083850] md: If you don't use raid, use raid=noautodetect [ 8.089836] md: Autodetecting RAID arrays. [ 8.094065] md: autorun ... [ 8.096947] md: ... autorun DONE. [ 8.104366] VFS: Mounted root (nfs filesystem) on device 0:18. [ 8.110557] devtmpfs: mounted [ 8.113864] Freeing unused kernel memory: 960K [ 8.147264] Run /sbin/init as init process [ 8.207071] systemd[1]: System time before build time, advancing clock. [ 8.235106] NET: Registered protocol family 10 [ 8.239987] Segment Routing with IPv6 [ 8.249921] systemd[1]: systemd 237 running in system mode. (-PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 8.272027] systemd[1]: Detected architecture arm64.