| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1573543139-8533-4-git-send-email-eugen.hristev@microchip.com>
Date: Tue, 12 Nov 2019 07:19:56 +0000
From: <Eugen.Hristev@...rochip.com>
To: <robh+dt@...nel.org>, <Nicolas.Ferre@...rochip.com>,
<alexandre.belloni@...tlin.com>, <Ludovic.Desroches@...rochip.com>
CC: <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, <Eugen.Hristev@...rochip.com>
Subject: [PATCH 4/4] ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and
wlsom1-ek
From: Eugen Hristev <eugen.hristev@...rochip.com>
This is the addition of a new Evaluation Kit the SAMA5D27-WLSOM1-EK.
It's based on the Microchip WireLess SoM which contains the
SAMA5D27 LPDDR2 2Gbits SiP.
[nicolas.ferre@...rochip.com]: initial implementation
Signed-off-by: Nicolas Ferre <nicolas.ferre@...rochip.com>
[eugen.hristev@...rochip.com]: ported to new kernel version,
[eugen.hristev@...rochip.com]: addition of peripherals (adc, pmic, qspi, uart)
Signed-off-by: Eugen Hristev <eugen.hristev@...rochip.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi | 304 ++++++++++++++++++++++++++
arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts | 270 +++++++++++++++++++++++
3 files changed, 575 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
create mode 100644 arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4ac0531..3beb450 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -49,6 +49,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox3-hs.dtb \
at91-nattis-2-natte-2.dtb \
at91-sama5d27_som1_ek.dtb \
+ at91-sama5d27_wlsom1_ek.dtb \
at91-sama5d2_ptc_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
new file mode 100644
index 0000000..db3e223
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d27_wlsom1.dtsi - Device Tree file for SAMA5D27 WLSOM1
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Nicolas Ferre <nicolas.ferre@...rocihp.com>
+ * Author: Eugen Hristev <eugen.hristev@...rocihp.com>
+ */
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+ model = "Microchip SAMA5D27 WLSOM1";
+ compatible = "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <24000000>;
+ };
+ };
+};
+
+&flx1 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+
+ uart6: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+ clock-names = "usart";
+ pinctrl-0 = <&pinctrl_flx1_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&i2c0 {
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&i2c1 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+
+ mcp16502@5b {
+ compatible = "microchip,mcp16502";
+ reg = <0x5b>;
+ status = "okay";
+ lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
+
+ regulators {
+ vdd_3v3: VDD_IO {
+ regulator-name = "VDD_IO";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vddio_ddr: VDD_DDR {
+ regulator-name = "VDD_DDR";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1200000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1200000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vdd_core: VDD_CORE {
+ regulator-name = "VDD_CORE";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vdd_ddr: VDD_OTHER {
+ regulator-name = "VDD_OTHER";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&macb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_default>;
+ phy-mode = "rmii";
+
+ ethernet-phy@0 {
+ reg = <0x0>;
+ interrupt-parent = <&pioA>;
+ interrupts = <PIN_PB24 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_phy_irq>;
+ };
+};
+
+&pmc {
+ atmel,osc-bypass;
+};
+
+&qspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi1_default>;
+ status = "disabled";
+
+ qspi1_flash: spi_flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ m25p,fast-read;
+ status = "disabled";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@...00 {
+ label = "bootloader";
+ reg = <0x40000 0xc0000>;
+ };
+
+ bootloaderenvred@...000 {
+ label = "bootloader env redundant";
+ reg = <0x100000 0x40000>;
+ };
+
+ bootloaderenv@...000 {
+ label = "bootloader env";
+ reg = <0x140000 0x40000>;
+ };
+
+ dtb@...000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@...000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+ };
+};
+
+&pioA {
+ pinctrl_flx1_default: flx1_usart_default {
+ pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+ <PIN_PA23__FLEXCOM1_IO1>,
+ <PIN_PA25__FLEXCOM1_IO3>,
+ <PIN_PA26__FLEXCOM1_IO4>;
+ bias-disable;
+ };
+
+ pinctrl_i2c0_default: i2c0_default {
+ pinmux = <PIN_PD21__TWD0>,
+ <PIN_PD22__TWCK0>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PD19__TWD1>,
+ <PIN_PD20__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_default: macb0_default {
+ pinmux = <PIN_PB14__GTXCK>,
+ <PIN_PB15__GTXEN>,
+ <PIN_PB16__GRXDV>,
+ <PIN_PB17__GRXER>,
+ <PIN_PB18__GRX0>,
+ <PIN_PB19__GRX1>,
+ <PIN_PB20__GTX0>,
+ <PIN_PB21__GTX1>,
+ <PIN_PB22__GMDC>,
+ <PIN_PB23__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PB24__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_qspi1_default: qspi1_default {
+ pinmux = <PIN_PB5__QSPI1_SCK>,
+ <PIN_PB6__QSPI1_CS>,
+ <PIN_PB7__QSPI1_IO0>,
+ <PIN_PB8__QSPI1_IO1>,
+ <PIN_PB9__QSPI1_IO2>,
+ <PIN_PB10__QSPI1_IO3>;
+ bias-pull-up;
+ };
+};
+
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
new file mode 100644
index 0000000..0b9fa29
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d27_wlsom1_ek.dts - Device Tree file for SAMA5D27 WLSOM1 EK
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Nicolas Ferre <nicolas.ferre@...rocihp.com>
+ */
+/dts-v1/;
+#include "at91-sama5d27_wlsom1.dtsi"
+
+/ {
+ model = "Microchip SAMA5D27 WLSOM1 EK";
+ compatible = "microchip,sama5d27-wlsom1-ek", "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+ aliases {
+ serial0 = &uart0; /* DBGU */
+ serial1 = &uart6; /* BT */
+ serial2 = &uart5; /* mikro BUS 2 */
+ serial3 = &uart3; /* mikro BUS 1 */
+ i2c1 = &i2c1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+ status = "okay";
+
+ sw4 {
+ label = "USER BUTTON";
+ gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+ status = "okay";
+
+ red {
+ label = "red";
+ gpios = <&pioA PIN_PA6 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "green";
+ gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&adc {
+ vddana-supply = <&vdd_3v3>;
+ vref-supply = <&vdd_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc_default>;
+ status = "okay";
+};
+
+&flx0 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "okay";
+
+ uart5: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+ clock-names = "usart";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ pinctrl-names = "default";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+};
+
+&flx1 {
+ status = "okay";
+
+ uart6: serial@200 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+};
+
+&macb0 {
+ status = "okay";
+};
+
+&pioA {
+ /*
+ * There is no real pinmux for ADC, if the pin
+ * is not requested by another peripheral then
+ * the muxing is done when channel is enabled.
+ * Requesting pins for ADC is GPIO is
+ * encouraged to prevent conflicts and to
+ * disable bias in order to be in the same
+ * state when the pin is not muxed to the adc.
+ */
+ pinctrl_adc_default: adc_default {
+ pinmux = <PIN_PD25__GPIO>,
+ <PIN_PD26__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_flx0_default: flx0_usart_default {
+ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+ <PIN_PB29__FLEXCOM0_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_key_gpio_default: key_gpio_default {
+ pinmux = <PIN_PB2__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_led_gpio_default: led_gpio_default {
+ pinmux = <PIN_PA6__GPIO>,
+ <PIN_PA7__GPIO>,
+ <PIN_PA8__GPIO>;
+ bias-pull-down;
+ };
+
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>;
+ bias-disable;
+ };
+
+ ck_cd_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA12__SDMMC0_WP>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart0_default: uart0_default {
+ pinmux = <PIN_PB26__URXD0>,
+ <PIN_PB27__UTXD0>;
+ bias-disable;
+ };
+
+ pinctrl_uart3_default: uart3_default {
+ pinmux = <PIN_PB11__URXD3>,
+ <PIN_PB12__UTXD3>;
+ bias-disable;
+ };
+
+ pinctrl_pwm0_default: pwm0_default {
+ pinmux = <PIN_PA31__PWML0>,
+ <PIN_PA30__PWMH0>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PA10__GPIO>;
+ bias-disable;
+ };
+};
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default>;
+ status = "okay";
+};
+
+&qspi1 {
+ status = "okay";
+
+ qspi1_flash: spi_flash@0 {
+ status = "okay";
+ };
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ mmc-ddr-3_3v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ status = "okay";
+};
+
+&shutdown_controller {
+ atmel,shdwc-debouncer = <976>;
+ atmel,wakeup-rtc-timer;
+
+ input@0 {
+ reg = <0>;
+ atmel,wakeup-type = "low";
+ };
+};
+
+&tcb0 {
+ timer0: timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>;
+ };
+
+ timer1: timer@1 {
+ compatible = "atmel,tcb-timer";
+ reg = <1>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+};
+
+&usb1 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioA PIN_PA10 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+};
+
+&usb2 {
+ phy_type = "hsic";
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
--
2.7.4
Powered by blists - more mailing lists