Message-ID: <20191112160258.GA1833@khorivan>
Date:   Tue, 12 Nov 2019 18:03:00 +0200
From:   Ivan Khoronzhuk <ivan.khoronzhuk@...aro.org>
To:     Po Liu <po.liu@....com>
Cc:     Claudiu Manoil <claudiu.manoil@....com>,
        "davem@...emloft.net" <davem@...emloft.net>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
        "vinicius.gomes@...el.com" <vinicius.gomes@...el.com>,
        Vladimir Oltean <vladimir.oltean@....com>,
        Alexandru Marginean <alexandru.marginean@....com>,
        Xiaoliang Yang <xiaoliang.yang_1@....com>,
        Roy Zang <roy.zang@....com>, Mingkai Hu <mingkai.hu@....com>,
        Jerry Huang <jerry.huang@....com>, Leo Li <leoyang.li@....com>
Subject: Re: [net-next, 1/2] enetc: Configure the Time-Aware Scheduler via
 tc-taprio offload

On Mon, Nov 11, 2019 at 04:41:26AM +0000, Po Liu wrote:
>ENETC supports in hardware for time-based egress shaping according
>to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
>hardware offload method qdisc tc-taprio method.
>Also update cbdr writeback to up level since control bd ring may
>writeback data to control bd ring.
>
>Signed-off-by: Po Liu <Po.Liu@....com>
>Singed-off-by: Vladimir Oltean <vladimir.oltean@....com>
>Signed-off-by: Claudiu Manoil <claudiu.manoil@....com>
>---
> drivers/net/ethernet/freescale/enetc/Makefile |   1 +
> drivers/net/ethernet/freescale/enetc/enetc.c  |  19 ++-
> drivers/net/ethernet/freescale/enetc/enetc.h  |   2 +
> .../net/ethernet/freescale/enetc/enetc_cbdr.c |   5 +-
> .../net/ethernet/freescale/enetc/enetc_hw.h   | 150 ++++++++++++++++--
> .../net/ethernet/freescale/enetc/enetc_qos.c  | 130 +++++++++++++++
> 6 files changed, 285 insertions(+), 22 deletions(-)
> create mode 100644 drivers/net/ethernet/freescale/enetc/enetc_qos.c
>
>diff --git a/drivers/net/ethernet/freescale/enetc/Makefile b/drivers/net/ethernet/freescale/enetc/Makefile
>index d200c27c3bf6..389f722efc43 100644
>--- a/drivers/net/ethernet/freescale/enetc/Makefile
>+++ b/drivers/net/ethernet/freescale/enetc/Makefile
>@@ -5,6 +5,7 @@ common-objs := enetc.o enetc_cbdr.o enetc_ethtool.o
> obj-$(CONFIG_FSL_ENETC) += fsl-enetc.o
> fsl-enetc-y := enetc_pf.o enetc_mdio.o $(common-objs)
> fsl-enetc-$(CONFIG_PCI_IOV) += enetc_msg.o
>+fsl-enetc-$(CONFIG_NET_SCH_TAPRIO) += enetc_qos.o
>
> obj-$(CONFIG_FSL_ENETC_VF) += fsl-enetc-vf.o
> fsl-enetc-vf-y := enetc_vf.o $(common-objs)
>diff --git a/drivers/net/ethernet/freescale/enetc/enetc.c b/drivers/net/ethernet/freescale/enetc/enetc.c
>index 3e8f9819f08c..d58dbc2c4270 100644
>--- a/drivers/net/ethernet/freescale/enetc/enetc.c
>+++ b/drivers/net/ethernet/freescale/enetc/enetc.c
>@@ -1427,8 +1427,7 @@ int enetc_close(struct net_device *ndev)
> 	return 0;
> }
>
>-int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,
>-		   void *type_data)
>+int enetc_setup_tc_mqprio(struct net_device *ndev, void *type_data)
> {
> 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
> 	struct tc_mqprio_qopt *mqprio = type_data;
>@@ -1436,9 +1435,6 @@ int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,
> 	u8 num_tc;
> 	int i;
>
>-	if (type != TC_SETUP_QDISC_MQPRIO)
>-		return -EOPNOTSUPP;
>-
> 	mqprio->hw = TC_MQPRIO_HW_OFFLOAD_TCS;
> 	num_tc = mqprio->num_tc;
>
>@@ -1483,6 +1479,19 @@ int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,
> 	return 0;
> }
>
>+int enetc_setup_tc(struct net_device *ndev, enum tc_setup_type type,
>+		   void *type_data)
>+{
>+	switch (type) {
>+	case TC_SETUP_QDISC_MQPRIO:
>+		return enetc_setup_tc_mqprio(ndev, type_data);

This patch is for taprio offload, I see that mqprio is related and is part of
taprio offload configuration. But taprio offload has own mqprio settings.
The taprio mqprio part is not offloaded with TC_SETUP_QDISC_MQPRIO.

So, a combination of mqprio and tario qdiscs used.
Could you please share the commands were used for your setup?

And couple interesting questions about all of this:
- The taprio qdisc has to have mqprio settings, but if it's done with
mqprio then it just skipped (by reading tc class num).
- If no separate mqprio qdisc configuration then mqprio conf from taprio
is set, who should restore tc mappings when taprio qdisc is unloaded?

Maybe there is reason to implement TC_SETUP_QDISC_MQPRIO offload in taprio
since it's required feature?

Would be better to move changes for mqprio in separate patch with explanation.

>+	case TC_SETUP_QDISC_TAPRIO:
>+		return enetc_setup_tc_taprio(ndev, type_data);
>+	default:
>+		return -EOPNOTSUPP;
>+	}
>+}
>+
> struct net_device_stats *enetc_get_stats(struct net_device *ndev)
> {
> 	struct enetc_ndev_priv *priv = netdev_priv(ndev);
>diff --git a/drivers/net/ethernet/freescale/enetc/enetc.h b/drivers/net/ethernet/freescale/enetc/enetc.h
>index 541b4e2073fe..8676631041d5 100644
>--- a/drivers/net/ethernet/freescale/enetc/enetc.h
>+++ b/drivers/net/ethernet/freescale/enetc/enetc.h
>@@ -244,3 +244,5 @@ int enetc_set_fs_entry(struct enetc_si *si, struct enetc_cmd_rfse *rfse,
> void enetc_set_rss_key(struct enetc_hw *hw, const u8 *bytes);
> int enetc_get_rss_table(struct enetc_si *si, u32 *table, int count);
> int enetc_set_rss_table(struct enetc_si *si, const u32 *table, int count);
>+int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd);
>+int enetc_setup_tc_taprio(struct net_device *ndev, void *type_data);
>diff --git a/drivers/net/ethernet/freescale/enetc/enetc_cbdr.c b/drivers/net/ethernet/freescale/enetc/enetc_cbdr.c
>index de466b71bf8f..201cbc362e33 100644
>--- a/drivers/net/ethernet/freescale/enetc/enetc_cbdr.c
>+++ b/drivers/net/ethernet/freescale/enetc/enetc_cbdr.c
>@@ -32,7 +32,7 @@ static int enetc_cbd_unused(struct enetc_cbdr *r)
> 		r->bd_count;
> }
>
>-static int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd)
>+int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd)
> {
> 	struct enetc_cbdr *ring = &si->cbd_ring;
> 	int timeout = ENETC_CBDR_TIMEOUT;
>@@ -66,6 +66,9 @@ static int enetc_send_cmd(struct enetc_si *si, struct enetc_cbd *cbd)
> 	if (!timeout)
> 		return -EBUSY;
>
>+	/* CBD may writeback data, feedback up level */
>+	*cbd = *dest_cbd;
>+
> 	enetc_clean_cbdr(si);
>
> 	return 0;
>diff --git a/drivers/net/ethernet/freescale/enetc/enetc_hw.h b/drivers/net/ethernet/freescale/enetc/enetc_hw.h
>index 88276299f447..75a7c0f1f8ce 100644
>--- a/drivers/net/ethernet/freescale/enetc/enetc_hw.h
>+++ b/drivers/net/ethernet/freescale/enetc/enetc_hw.h
>@@ -18,6 +18,7 @@
> #define ENETC_SICTR0	0x18
> #define ENETC_SICTR1	0x1c
> #define ENETC_SIPCAPR0	0x20
>+#define ENETC_SIPCAPR0_QBV	BIT(4)
> #define ENETC_SIPCAPR0_RSS	BIT(8)
> #define ENETC_SIPCAPR1	0x24
> #define ENETC_SITGTGR	0x30
>@@ -148,6 +149,12 @@ enum enetc_bdr_type {TX, RX};
> #define ENETC_PORT_BASE		0x10000
> #define ENETC_PMR		0x0000
> #define ENETC_PMR_EN	GENMASK(18, 16)
>+#define ENETC_PMR_PSPEED_MASK GENMASK(11, 8)
>+#define ENETC_PMR_PSPEED_10M 0x000
>+#define ENETC_PMR_PSPEED_100M 0x100
>+#define ENETC_PMR_PSPEED_1000M 0x200
>+#define ENETC_PMR_PSPEED_2500M 0x400
>+
> #define ENETC_PSR		0x0004 /* RO */
> #define ENETC_PSIPMR		0x0018
> #define ENETC_PSIPMR_SET_UP(n)	BIT(n) /* n = SI index */
>@@ -440,22 +447,6 @@ union enetc_rx_bd {
> #define EMETC_MAC_ADDR_FILT_RES	3 /* # of reserved entries at the beginning */
> #define ENETC_MAX_NUM_VFS	2
>
>-struct enetc_cbd {
>-	union {
>-		struct {
>-			__le32 addr[2];
>-			__le32 opt[4];
>-		};
>-		__le32 data[6];
>-	};
>-	__le16 index;
>-	__le16 length;
>-	u8 cmd;
>-	u8 cls;
>-	u8 _res;
>-	u8 status_flags;
>-};
>-
> #define ENETC_CBD_FLAGS_SF	BIT(7) /* short format */
> #define ENETC_CBD_STATUS_MASK	0xf
>
>@@ -554,3 +545,130 @@ static inline void enetc_set_bdr_prio(struct enetc_hw *hw, int bdr_idx,
> 	val |= ENETC_TBMR_SET_PRIO(prio);
> 	enetc_txbdr_wr(hw, bdr_idx, ENETC_TBMR, val);
> }
>+
>+enum bdcr_cmd_class {
>+	BDCR_CMD_UNSPEC = 0,
>+	BDCR_CMD_MAC_FILTER,
>+	BDCR_CMD_VLAN_FILTER,
>+	BDCR_CMD_RSS,
>+	BDCR_CMD_RFS,
>+	BDCR_CMD_PORT_GCL,
>+	BDCR_CMD_RECV_CLASSIFIER,
>+	__BDCR_CMD_MAX_LEN,
>+	BDCR_CMD_MAX_LEN = __BDCR_CMD_MAX_LEN - 1,
>+};
>+
>+/* class 5, command 0 */
>+struct tgs_gcl_conf {
>+	u8	atc;	/* init gate value */
>+	u8	res[7];
>+	union {
>+		struct {
>+			u8	res1[4];
>+			__le16	acl_len;
>+			u8	res2[2];
>+		};
>+		struct {
>+			u32 cctl;
>+			u32 ccth;
>+		};
>+	};
>+};
>+
>+#define ENETC_CBDR_SGL_IOMEN	BIT(0)
>+#define ENETC_CBDR_SGL_IPVEN	BIT(3)
>+#define ENETC_CBDR_SGL_GTST	BIT(4)
>+#define ENETC_CBDR_SGL_IPV_MASK 0xe
>+
>+/* gate control list entry */
>+struct gce {
>+	u32	period;
>+	u8	gate;
>+	u8	res[3];
>+};
>+
>+/* tgs_gcl_conf address point to this data space */
>+struct tgs_gcl_data {
>+	u32	btl;
>+	u32	bth;
>+	u32	ct;
>+	u32	cte;
>+};
>+
>+/* class 5, command 1 */
>+struct tgs_gcl_query {
>+		u8	res[12];
>+		union {
>+			struct {
>+				__le16	acl_len; /* admin list length */
>+				__le16	ocl_len; /* operation list length */
>+			};
>+			struct {
>+				u16 admin_list_len;
>+				u16 oper_list_len;
>+			};
>+		};
>+};
>+
>+/* tgs_gcl_query command response data format */
>+struct tgs_gcl_resp {
>+	u32 abtl;	/* base time */
>+	u32 abth;
>+	u32 act;	/* cycle time */
>+	u32 acte;	/* cycle time extend */
>+	u32 cctl;	/* config change time */
>+	u32 ccth;
>+	u32 obtl;	/* operation base time */
>+	u32 obth;
>+	u32 oct;	/* operation cycle time */
>+	u32 octe;	/* operation cycle time extend */
>+	u32 ccel;	/* config change error */
>+	u32 cceh;
>+};
>+
>+struct enetc_cbd {
>+	union{
>+		struct {
>+			__le32	addr[2];
>+			union {
>+				__le32	opt[4];
>+				struct tgs_gcl_conf	gcl_conf;
>+				struct tgs_gcl_query	gcl_query;
>+			};
>+		};	/* Long format */
>+		__le32 data[6];
>+	};
>+	__le16 index;
>+	__le16 length;
>+	u8 cmd;
>+	u8 cls;
>+	u8 _res;
>+	u8 status_flags;
>+};
>+
>+#define ENETC_PTCFPR(n)		(0x1910 + (n) * 4) /* n = [0 ..7] */
>+#define ENETC_FPE		BIT(31)
>+
>+/* Port capability register 0 */
>+#define ENETC_PCAPR0_PSFPM	BIT(10)
>+#define ENETC_PCAPR0_PSFP	BIT(9)
>+#define ENETC_PCAPR0_TSN	BIT(4)
>+#define ENETC_PCAPR0_QBU	BIT(3)
>+
>+/* port time gating control register */
>+#define ENETC_QBV_PTGCR_OFFSET		0x11a00
>+#define ENETC_QBV_TGE			0x80000000
>+#define ENETC_QBV_TGPE			BIT(30)
>+#define ENETC_QBV_TGDROP_DISABLE	BIT(29)
>+
>+/* Port time gating capability register */
>+#define ENETC_QBV_PTGCAPR_OFFSET	0x11a08
>+#define ENETC_QBV_MAX_GCL_LEN_MASK	0xffff
>+
>+/* Port time gating admin gate list status register */
>+#define ENETC_QBV_PTGAGLSR_OFFSET	0x11a10
>+#define ENETC_QBV_CFG_PEND_MASK	0x00000002
>+
>+#define ENETC_TGLSTR			0xa200
>+#define ENETC_TGS_MIN_DIS_MASK		0x80000000
>+#define ENETC_MIN_LOOKAHEAD_MASK	0xffff
>diff --git a/drivers/net/ethernet/freescale/enetc/enetc_qos.c b/drivers/net/ethernet/freescale/enetc/enetc_qos.c
>new file mode 100644
>index 000000000000..036bb39c7a0b
>--- /dev/null
>+++ b/drivers/net/ethernet/freescale/enetc/enetc_qos.c
>@@ -0,0 +1,130 @@
>+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>+/* Copyright 2019 NXP */
>+
>+#include "enetc.h"
>+
>+#include <net/pkt_sched.h>
>+
>+static u16 enetc_get_max_gcl_len(struct enetc_hw *hw)
>+{
>+	return enetc_rd(hw, ENETC_QBV_PTGCAPR_OFFSET)
>+		& ENETC_QBV_MAX_GCL_LEN_MASK;
>+}
>+
>+static int enetc_setup_taprio(struct net_device *ndev,
>+			      struct tc_taprio_qopt_offload *admin_conf)
>+{
>+	struct enetc_ndev_priv *priv = netdev_priv(ndev);
>+	struct enetc_cbd cbd = {.cmd = 0};
>+	struct tgs_gcl_conf *gcl_config;
>+	struct tgs_gcl_data *gcl_data;
>+	struct gce *gce;
>+	dma_addr_t dma;
>+	u16 data_size;
>+	u16 gcl_len;
>+	u32 temp;
>+	int i;
>+
>+	gcl_len = admin_conf->num_entries;
>+	if (gcl_len > enetc_get_max_gcl_len(&priv->si->hw))
>+		return -EINVAL;
>+
>+	if (admin_conf->enable) {
>+		enetc_wr(&priv->si->hw,
>+			 ENETC_QBV_PTGCR_OFFSET,
>+			 temp & (~ENETC_QBV_TGE));
>+		usleep_range(10, 20);
>+		enetc_wr(&priv->si->hw,
>+			 ENETC_QBV_PTGCR_OFFSET,
>+			 temp | ENETC_QBV_TGE);
>+	} else {
>+		enetc_wr(&priv->si->hw,
>+			 ENETC_QBV_PTGCR_OFFSET,
>+			 temp & (~ENETC_QBV_TGE));
>+		return 0;
>+	}
>+
>+	/* Configure the (administrative) gate control list using the
>+	 * control BD descriptor.
>+	 */
>+	gcl_config = &cbd.gcl_conf;
>+
>+	data_size = sizeof(struct tgs_gcl_data) + gcl_len * sizeof(struct gce);
>+
>+	gcl_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
>+	if (!gcl_data)
>+		return -ENOMEM;
>+
>+	gce = (struct gce *)(gcl_data + 1);
>+
>+	/* Since no initial state config in taprio, set gates open as default.
>+	 */
>+	gcl_config->atc = 0xff;
>+	gcl_config->acl_len = cpu_to_le16(gcl_len);
>+
>+	if (!admin_conf->base_time) {
>+		gcl_data->btl =
>+			cpu_to_le32(enetc_rd(&priv->si->hw, ENETC_SICTR0));
>+		gcl_data->bth =
>+			cpu_to_le32(enetc_rd(&priv->si->hw, ENETC_SICTR1));
>+	} else {
>+		gcl_data->btl =
>+			cpu_to_le32(lower_32_bits(admin_conf->base_time));
>+		gcl_data->bth =
>+			cpu_to_le32(upper_32_bits(admin_conf->base_time));
>+	}
>+
>+	gcl_data->ct = cpu_to_le32(admin_conf->cycle_time);
>+	gcl_data->cte = cpu_to_le32(admin_conf->cycle_time_extension);
>+
>+	for (i = 0; i < gcl_len; i++) {
>+		struct tc_taprio_sched_entry *temp_entry;
>+		struct gce *temp_gce = gce + i;
>+
>+		temp_entry = &admin_conf->entries[i];
>+
>+		temp_gce->gate = cpu_to_le32(temp_entry->gate_mask);
>+		temp_gce->period = cpu_to_le32(temp_entry->interval);
>+	}
>+
>+	cbd.length = cpu_to_le16(data_size);
>+	cbd.status_flags = 0;
>+
>+	dma = dma_map_single(&priv->si->pdev->dev, gcl_data,
>+			     data_size, DMA_TO_DEVICE);
>+	if (dma_mapping_error(&priv->si->pdev->dev, dma)) {
>+		netdev_err(priv->si->ndev, "DMA mapping failed!\n");
>+		kfree(gcl_data);
>+		return -ENOMEM;
>+	}
>+
>+	cbd.addr[0] = lower_32_bits(dma);
>+	cbd.addr[1] = upper_32_bits(dma);
>+	cbd.cls = BDCR_CMD_PORT_GCL;
>+
>+	/* Updated by ENETC on completion of the configuration
>+	 * command. A zero value indicates success.
>+	 */
>+	cbd.status_flags = 0;
>+
>+	enetc_send_cmd(priv->si, &cbd);
>+
>+	dma_unmap_single(&priv->si->pdev->dev, dma, data_size, DMA_TO_DEVICE);
>+	kfree(gcl_data);
>+
>+	return 0;
>+}
>+
>+int enetc_setup_tc_taprio(struct net_device *ndev, void *type_data)
>+{
>+	struct tc_taprio_qopt_offload *taprio = type_data;
>+	struct enetc_ndev_priv *priv = netdev_priv(ndev);
>+	int i;
>+
>+	for (i = 0; i < priv->num_tx_rings; i++)
>+		enetc_set_bdr_prio(&priv->si->hw,
>+				   priv->tx_ring[i]->index,
>+				   taprio->enable ? i : 0);
>+
>+	return enetc_setup_taprio(ndev, taprio);
>+}
>-- 
>2.17.1
>

-- 
Regards,
Ivan Khoronzhuk

Powered by blists - more mailing lists