[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <8465b8c3-db4b-31fd-a299-3d5251ec99cf@ti.com>
Date: Thu, 21 Nov 2019 13:04:35 +0200
From: Grygorii Strashko <grygorii.strashko@...com>
To: Caleb Robey <c-robey@...com>, <linux-omap@...r.kernel.org>
CC: Jason Kridner <jkridner@...il.com>,
Lokesh Vutla <lokeshvutla@...com>, Jason Kridner <jdk@...com>,
Faiz Abbas <faiz_abbas@...com>,
Andreas Dannenberg <dannenberg@...com>,
Jean-Jacques Hiblot <jjhiblot@...com>,
Praneeth Bajjuri <praneeth@...com>,
"Andrew F . Davis" <afd@...com>, Tom Rini <trini@...sulko.com>,
Robert Nelson <robertcnelson@...il.com>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
BenoƮt Cousson <bcousson@...libre.com>,
Tony Lindgren <tony@...mide.com>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 1/1] ARM: dts: am5729: beaglebone-ai: adding device tree
On 19/11/2019 22:28, Caleb Robey wrote:
> From: Jason Kridner <jdk@...com>
>
> BeagleBoard.org BeagleBone AI is an open source hardware single
> board computer based on the Texas Instruments AM5729 SoC featuring
> dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital
> signal processor (DSP), quad-core embedded vision engine (EVE),
> Arm Cortex-M4 processors, dual programmable realtime unit
> industrial control subsystems and more. The board features 1GB
> DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash,
> 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion
> headers.
>
> For more information, refer to:
> https://beaglebone.ai
>
> This patch introduces the BeagleBone AI device tree.
>
> Note that the device use the "ti,tpd12s016" component which is
> software compatible with "ti,tpd12s015". Thus we only use the
> latter driver.
>
> Signed-off-by: Jason Kridner <jdk@...com>
> Signed-off-by: Caleb Robey <c-robey@...com>
> Cc: Robert Nelson <robertcnelson@...il.com>
>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/am5729-beagleboneai.dts | 782 ++++++++++++++++++++++
> 2 files changed, 783 insertions(+)
> create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b21b3a64641a..b1154dbda73c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
[..]
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&davinci_mdio {
> + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
> + reset-delay-us = <2>;
> +
> + phy0: ethernet-phy@1 {
> + reg = <4>;
> + compatible = "ethernet-phy-id004d.d072",
> + "ethernet-phy-ieee802.3-c22";
Pls, do not ignore my comments.
Above compatible should not be required.
> + eee-broken-100tx;
> + eee-broken-1000t;
> + };
> +};
> +
> +&mac {
> + slaves = <1>;
> + status = "okay";
> +};
Pls, move cpsw node here
> +
> +&ocp {
> + pruss1_shmem: pruss_shmem@...00000 {
> + status = "okay";
> + compatible = "ti,pruss-shmem";
> + reg = <0x4b200000 0x020000>;
> + };
> +
[..]
> +
> +&cpsw_emac0 {
> + phy-handle = <&phy0>;
> + phy-mode = "rgmii";
> +};
Move it up, pls.
--
Best regards,
grygorii
Powered by blists - more mailing lists