| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20191125170428.76069-1-stephan@gerhold.net>
Date: Mon, 25 Nov 2019 18:04:25 +0100
From: Stephan Gerhold <stephan@...hold.net>
To: Linus Walleij <linus.walleij@...aro.org>
Cc: Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, Stephan Gerhold <stephan@...hold.net>
Subject: [PATCH 1/4] ARM: dts: ux500: Disable I2C/SPI buses by default
At the moment, all 5 I2C and 6 SPI buses are probed and exposed
to user-space by default - even if they are not muxed to any pins
on the board. This means that user-space sees an I2C/SPI bus that
cannot be actually used properly.
In some cases this was used to put the corresponding pins into
a low power sleep mode - but even then the pins first need to be
configured by the board-specific device tree part.
Avoid exposing unconfigured devices to user-space by disabling
the I2C/SPI buses by default. Enable them in the board device trees
when needed.
Signed-off-by: Stephan Gerhold <stephan@...hold.net>
---
arch/arm/boot/dts/ste-dbx5x0.dtsi | 22 ++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 4 ++++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 1 +
arch/arm/boot/dts/ste-snowball.dts | 5 +++++
4 files changed, 32 insertions(+)
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index a53657b83288..899368aa6ff7 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -646,6 +646,8 @@
clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
i2c@...22000 {
@@ -662,6 +664,8 @@
clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
i2c@...28000 {
@@ -678,6 +682,8 @@
clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
i2c@...10000 {
@@ -694,6 +700,8 @@
clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
i2c@...2a000 {
@@ -710,6 +718,8 @@
clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
spi@...02000 {
@@ -724,6 +734,8 @@
<&dma 8 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
spi@...03000 {
@@ -738,6 +750,8 @@
<&dma 9 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
spi@...1a000 {
@@ -753,6 +767,8 @@
<&dma 0 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
spi@...12000 {
@@ -768,6 +784,8 @@
<&dma 35 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
spi@...11000 {
@@ -783,6 +801,8 @@
<&dma 33 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
spi@...29000 {
@@ -798,6 +818,8 @@
<&dma 40 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
ux500_serial0: uart@...20000 {
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 7613a40421d5..5eafd5d8a8cd 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -39,18 +39,21 @@
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c0_a_1_default>;
pinctrl-1 = <&i2c0_a_1_sleep>;
+ status = "okay";
};
i2c@...22000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c1_b_2_default>;
pinctrl-1 = <&i2c1_b_2_sleep>;
+ status = "okay";
};
i2c@...28000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c2_b_2_default>;
pinctrl-1 = <&i2c2_b_2_sleep>;
+ status = "okay";
lp5521@33 {
compatible = "national,lp5521";
reg = <0x33>;
@@ -98,6 +101,7 @@
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c3_c_2_default>;
pinctrl-1 = <&i2c3_c_2_sleep>;
+ status = "okay";
};
/* ST6G3244ME level translator for 1.8/2.9 V */
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index a036defdf164..937f942f0961 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -58,6 +58,7 @@
*/
pinctrl-names = "default";
pinctrl-0 = <&ssp0_hrefprev60_mode>;
+ status = "okay";
};
// External Micro SD slot
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 8b80dcdf6e5b..ce136412b6da 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -307,18 +307,21 @@
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c0_a_1_default>;
pinctrl-1 = <&i2c0_a_1_sleep>;
+ status = "okay";
};
i2c@...22000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c1_b_2_default>;
pinctrl-1 = <&i2c1_b_2_sleep>;
+ status = "okay";
};
i2c@...28000 {
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c2_b_2_default>;
pinctrl-1 = <&i2c2_b_2_sleep>;
+ status = "okay";
lsm303dlh@18 {
/* Accelerometer */
compatible = "st,lsm303dlh-accel";
@@ -369,11 +372,13 @@
pinctrl-names = "default","sleep";
pinctrl-0 = <&i2c3_c_2_default>;
pinctrl-1 = <&i2c3_c_2_sleep>;
+ status = "okay";
};
spi@...02000 {
pinctrl-names = "default";
pinctrl-0 = <&ssp0_snowball_mode>;
+ status = "okay";
};
prcmu@...57000 {
--
2.24.0
Powered by blists - more mailing lists