| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20191205120844.GB8514@bogon.m.sigxcpu.org>
Date: Thu, 5 Dec 2019 13:08:44 +0100
From: Guido Günther <agx@...xcpu.org>
To: Robert Chiras <robert.chiras@....com>
Cc: dl-linux-imx <linux-imx@....com>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"robh+dt@...nel.org" <robh+dt@...nel.org>,
"narmstrong@...libre.com" <narmstrong@...libre.com>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
"festevam@...il.com" <festevam@...il.com>,
"lee.jones@...aro.org" <lee.jones@...aro.org>,
"jernej.skrabec@...l.net" <jernej.skrabec@...l.net>,
"daniel@...ll.ch" <daniel@...ll.ch>,
"mark.rutland@....com" <mark.rutland@....com>,
"a.hajda@...sung.com" <a.hajda@...sung.com>,
"dri-devel@...ts.freedesktop.org" <dri-devel@...ts.freedesktop.org>,
"jonas@...boo.se" <jonas@...boo.se>,
"shawnguo@...nel.org" <shawnguo@...nel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
"airlied@...ux.ie" <airlied@...ux.ie>,
"sam@...nborg.org" <sam@...nborg.org>,
"Laurent.pinchart@...asonboard.com"
<Laurent.pinchart@...asonboard.com>,
"kernel@...gutronix.de" <kernel@...gutronix.de>,
"arnd@...db.de" <arnd@...db.de>,
"s.hauer@...gutronix.de" <s.hauer@...gutronix.de>
Subject: Re: [EXT] [PATCH v8 2/2] drm/bridge: Add NWL MIPI DSI host
controller support
Hi Robert,
On Wed, Dec 04, 2019 at 12:24:39PM +0000, Robert Chiras wrote:
> On Mi, 2019-12-04 at 13:06 +0100, Guido Günther wrote:
> > Hi Robert,
> > On Tue, Dec 03, 2019 at 09:50:03AM +0000, Robert Chiras wrote:
> > >
> > > Hi Guido,
> > >
> > > Since your last revision sent, I've done more tests here and found
> > > a
> > > few more improvements that could be added to this driver.
> > > See inline.
> > >
> > > On Lu, 2019-12-02 at 20:35 +0100, Guido Günther wrote:
> > > >
> > > > Caution: EXT Email
> > > >
> > > > This adds initial support for the NWL MIPI DSI Host controller
> > > > found
> > > > on
> > > > i.MX8 SoCs.
> > > >
> > > > It adds support for the i.MX8MQ but the same IP can be found on
> > > > e.g. the i.MX8QXP.
> > > >
> > > > It has been tested on the Librem 5 devkit using mxsfb.
> > > >
> > > > Signed-off-by: Guido Günther <agx@...xcpu.org>
> > > > Co-developed-by: Robert Chiras <robert.chiras@....com>
> > > > Signed-off-by: Robert Chiras <robert.chiras@....com>
> > > > Tested-by: Robert Chiras <robert.chiras@....com>
> > > > ---
> > > > drivers/gpu/drm/bridge/Kconfig | 16 +
> > > > drivers/gpu/drm/bridge/Makefile | 3 +
> > > > drivers/gpu/drm/bridge/nwl-dsi.c | 1230
> > > > ++++++++++++++++++++++++++++++
> > > > drivers/gpu/drm/bridge/nwl-dsi.h | 144 ++++
> > > > 4 files changed, 1393 insertions(+)
> > > > create mode 100644 drivers/gpu/drm/bridge/nwl-dsi.c
> > > > create mode 100644 drivers/gpu/drm/bridge/nwl-dsi.h
> > > >
> > > > diff --git a/drivers/gpu/drm/bridge/Kconfig
> > > > b/drivers/gpu/drm/bridge/Kconfig
> > > > index 34362976cd6f..6fb534f55d22 100644
> > > > --- a/drivers/gpu/drm/bridge/Kconfig
> > > > +++ b/drivers/gpu/drm/bridge/Kconfig
> > > > @@ -65,6 +65,22 @@ config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW
> > > > to DP++. This is used with the i.MX6 imx-ldb
> > > > driver. You are likely to say N here.
> > > >
> > > > +config DRM_NWL_MIPI_DSI
> > > > + tristate "Northwest Logic MIPI DSI Host controller"
> > > > + depends on DRM
> > > > + depends on COMMON_CLK
> > > > + depends on OF && HAS_IOMEM
> > > > + select DRM_KMS_HELPER
> > > > + select DRM_MIPI_DSI
> > > > + select DRM_PANEL_BRIDGE
> > > > + select GENERIC_PHY_MIPI_DPHY
> > > > + select MFD_SYSCON
> > > > + select MULTIPLEXER
> > > > + select REGMAP_MMIO
> > > > + help
> > > > + This enables the Northwest Logic MIPI DSI Host
> > > > controller
> > > > as
> > > > + for example found on NXP's i.MX8 Processors.
> > > > +
> > > > config DRM_NXP_PTN3460
> > > > tristate "NXP PTN3460 DP/LVDS bridge"
> > > > depends on OF
> > > > diff --git a/drivers/gpu/drm/bridge/Makefile
> > > > b/drivers/gpu/drm/bridge/Makefile
> > > > index 4934fcf5a6f8..c3f3a43e9b8f 100644
> > > > --- a/drivers/gpu/drm/bridge/Makefile
> > > > +++ b/drivers/gpu/drm/bridge/Makefile
> > > > @@ -16,4 +16,7 @@ obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
> > > > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
> > > > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
> > > > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
> > > > +obj-$(CONFIG_DRM_NWL_MIPI_DSI) += nwl-dsi.o
> > > > obj-y += synopsys/
> > > > +
> > > > +header-test-y += nwl-dsi.h
> > > > diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c
> > > > b/drivers/gpu/drm/bridge/nwl-dsi.c
> > > > new file mode 100644
> > > > index 000000000000..023191894fe4
> > > > --- /dev/null
> > > > +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> > > > @@ -0,0 +1,1230 @@
> > > > +// SPDX-License-Identifier: GPL-2.0+
> > > > +/*
> > > > + * i.MX8 NWL MIPI DSI host driver
> > > > + *
> > > > + * Copyright (C) 2017 NXP
> > > > + * Copyright (C) 2019 Purism SPC
> > > > + */
> > > > +
> > > > +#include <linux/bitfield.h>
> > > > +#include <linux/clk.h>
> > > > +#include <linux/irq.h>
> > > > +#include <linux/math64.h>
> > > > +#include <linux/mfd/syscon.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/mux/consumer.h>
> > > > +#include <linux/of.h>
> > > > +#include <linux/of_platform.h>
> > > > +#include <linux/phy/phy.h>
> > > > +#include <linux/regmap.h>
> > > > +#include <linux/reset.h>
> > > > +#include <linux/sys_soc.h>
> > > > +#include <linux/time64.h>
> > > > +
> > > > +#include <drm/drm_atomic_helper.h>
> > > > +#include <drm/drm_bridge.h>
> > > > +#include <drm/drm_mipi_dsi.h>
> > > > +#include <drm/drm_of.h>
> > > > +#include <drm/drm_panel.h>
> > > > +#include <drm/drm_print.h>
> > > > +#include <drm/drm_probe_helper.h>
> > > > +
> > > > +#include <video/mipi_display.h>
> > > > +#include <video/videomode.h>
> > > > +
> > > > +#include "nwl-dsi.h"
> > > > +
> > > > +#define DRV_NAME "nwl-dsi"
> > > > +
> > > > +/* i.MX8 NWL quirks */
> > > > +/* i.MX8MQ errata E11418 */
> > > > +#define E11418_HS_MODE_QUIRK BIT(0)
> > > > +
> > > > +#define NWL_DSI_MIPI_FIFO_TIMEOUT msecs_to_jiffies(500)
> > > > +
> > > > +enum transfer_direction {
> > > > + DSI_PACKET_SEND,
> > > > + DSI_PACKET_RECEIVE,
> > > > +};
> > > > +
> > > > +/* Possible platform specific clocks */
> > > > +#define NWL_DSI_CLK_CORE "core"
> > > > +#define NWL_DSI_MAX_PLATFORM_CLOCKS 1
> > > > +
> > > > +#define NWL_DSI_ENDPOINT_LCDIF 0
> > > > +#define NWL_DSI_ENDPOINT_DCSS 1
> > > > +
> > > > +struct nwl_dsi_plat_clk_config {
> > > > + const char *id;
> > > > + struct clk *clk;
> > > > + bool present;
> > > > +};
> > > > +
> > > > +struct nwl_dsi_transfer {
> > > > + const struct mipi_dsi_msg *msg;
> > > > + struct mipi_dsi_packet packet;
> > > > + struct completion completed;
> > > > +
> > > > + int status; /* status of transmission */
> > > > + enum transfer_direction direction;
> > > > + bool need_bta;
> > > > + u8 cmd;
> > > > + u16 rx_word_count;
> > > > + size_t tx_len; /* in bytes */
> > > > + size_t rx_len; /* in bytes */
> > > > +};
> > > > +
> > > > +struct nwl_dsi {
> > > > + struct drm_bridge bridge;
> > > > + struct mipi_dsi_host dsi_host;
> > > > + struct drm_bridge *panel_bridge;
> > > > + struct device *dev;
> > > > + struct phy *phy;
> > > > + union phy_configure_opts phy_cfg;
> > > > + unsigned int quirks;
> > > > +
> > > > + struct regmap *regmap;
> > > > + int irq;
> > > > + struct reset_control *rstc;
> > > > + struct mux_control *mux;
> > > > +
> > > > + /* DSI clocks */
> > > > + struct clk *phy_ref_clk;
> > > > + struct clk *rx_esc_clk;
> > > > + struct clk *tx_esc_clk;
> > > > + /* Platform dependent clocks */
> > > > + struct nwl_dsi_plat_clk_config
> > > > clk_config[NWL_DSI_MAX_PLATFORM_CLOCKS];
> > > > +
> > > > + /* dsi lanes */
> > > > + u32 lanes;
> > > > + enum mipi_dsi_pixel_format format;
> > > > + struct drm_display_mode mode;
> > > > + unsigned long dsi_mode_flags;
> > > > + int error;
> > > > +
> > > > + struct nwl_dsi_transfer *xfer;
> > > > +
> > > > + const struct nwl_dsi_platform_data *pdata;
> > > > +};
> > > > +
> > > > +/* Platform specific hooks to enable other SoCs like the i.MX8QM
> > > > */
> > > > +struct nwl_dsi_platform_data {
> > > > + int (*poweron)(struct nwl_dsi *dsi);
> > > > + int (*poweroff)(struct nwl_dsi *dsi);
> > > > + int (*select_input)(struct nwl_dsi *dsi);
> > > > + int (*deselect_input)(struct nwl_dsi *dsi);
> > > > + struct nwl_dsi_plat_clk_config
> > > > clk_config[NWL_DSI_MAX_PLATFORM_CLOCKS];
> > > > +};
> > > > +
> > > > +static const struct regmap_config nwl_dsi_regmap_config = {
> > > > + .reg_bits = 16,
> > > > + .val_bits = 32,
> > > > + .reg_stride = 4,
> > > > + .max_register = NWL_DSI_IRQ_MASK2,
> > > > + .name = DRV_NAME,
> > > > +};
> > > > +
> > > > +static inline struct nwl_dsi *bridge_to_dsi(struct drm_bridge
> > > > *bridge)
> > > > +{
> > > > + return container_of(bridge, struct nwl_dsi, bridge);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_clear_error(struct nwl_dsi *dsi)
> > > > +{
> > > > + int ret = dsi->error;
> > > > +
> > > > + dsi->error = 0;
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static void nwl_dsi_write(struct nwl_dsi *dsi, unsigned int reg,
> > > > u32
> > > > val)
> > > > +{
> > > > + int ret;
> > > > +
> > > > + if (dsi->error)
> > > > + return;
> > > > +
> > > > + ret = regmap_write(dsi->regmap, reg, val);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dsi->dev,
> > > > + "Failed to write NWL DSI reg 0x%x:
> > > > %d\n", reg,
> > > > + ret);
> > > > + dsi->error = ret;
> > > > + }
> > > > +}
> > > > +
> > > > +static u32 nwl_dsi_read(struct nwl_dsi *dsi, u32 reg)
> > > > +{
> > > > + unsigned int val;
> > > > + int ret;
> > > > +
> > > > + if (dsi->error)
> > > > + return 0;
> > > > +
> > > > + ret = regmap_read(dsi->regmap, reg, &val);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to read NWL DSI
> > > > reg
> > > > 0x%x: %d\n",
> > > > + reg, ret);
> > > > + dsi->error = ret;
> > > > + }
> > > > + return val;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_get_dpi_pixel_format(enum
> > > > mipi_dsi_pixel_format
> > > > format)
> > > > +{
> > > > + switch (format) {
> > > > + case MIPI_DSI_FMT_RGB565:
> > > > + return NWL_DSI_PIXEL_FORMAT_16;
> > > > + case MIPI_DSI_FMT_RGB666:
> > > > + return NWL_DSI_PIXEL_FORMAT_18L;
> > > > + case MIPI_DSI_FMT_RGB666_PACKED:
> > > > + return NWL_DSI_PIXEL_FORMAT_18;
> > > > + case MIPI_DSI_FMT_RGB888:
> > > > + return NWL_DSI_PIXEL_FORMAT_24;
> > > > + default:
> > > > + return -EINVAL;
> > > > + }
> > > > +}
> > > > +
> > > > +/*
> > > > + * ps2bc - Picoseconds to byte clock cycles
> > > > + */
> > > > +static u32 ps2bc(struct nwl_dsi *dsi, unsigned long long ps)
> > > > +{
> > > > + u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> > > > +
> > > > + return DIV64_U64_ROUND_UP(ps * dsi->mode.clock * bpp,
> > > > + dsi->lanes * 8 * NSEC_PER_SEC);
> > > > +}
> > > > +
> > > > +/*
> > > > + * ui2bc - UI time periods to byte clock cycles
> > > > + */
> > > > +static u32 ui2bc(struct nwl_dsi *dsi, unsigned long long ui)
> > > > +{
> > > > + u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> > > > +
> > > > + return DIV64_U64_ROUND_UP(ui * dsi->lanes,
> > > > + dsi->mode.clock * 1000 * bpp);
> > > > +}
> > > > +
> > > > +/*
> > > > + * us2bc - micro seconds to lp clock cycles
> > > > + */
> > > > +static u32 us2lp(u32 lp_clk_rate, unsigned long us)
> > > > +{
> > > > + return DIV_ROUND_UP(us * lp_clk_rate, USEC_PER_SEC);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_config_host(struct nwl_dsi *dsi)
> > > > +{
> > > > + u32 cycles;
> > > > + struct phy_configure_opts_mipi_dphy *cfg = &dsi-
> > > > >
> > > > > phy_cfg.mipi_dphy;
> > > > +
> > > > + if (dsi->lanes < 1 || dsi->lanes > 4)
> > > > + return -EINVAL;
> > > > +
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "DSI Lanes %d\n", dsi-
> > > > >lanes);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_NUM_LANES, dsi->lanes -
> > > > 1);
> > > > +
> > > > + if (dsi->dsi_mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS)
> > > > {
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_NONCONTINUOUS_CLK,
> > > > 0x01);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_AUTOINSERT_EOTP,
> > > > 0x01);
> > > > + } else {
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_NONCONTINUOUS_CLK,
> > > > 0x00);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_AUTOINSERT_EOTP,
> > > > 0x00);
> > > > + }
> > > > +
> > > > + /* values in byte clock cycles */
> > > > + cycles = ui2bc(dsi, cfg->clk_pre);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_pre: 0x%x\n",
> > > > cycles);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_T_PRE, cycles);
> > > > + cycles = ps2bc(dsi, cfg->lpx + cfg->clk_prepare + cfg-
> > > > >
> > > > > clk_zero);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap (pre):
> > > > 0x%x\n",
> > > > cycles);
> > > > + cycles += ui2bc(dsi, cfg->clk_pre);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_post: 0x%x\n",
> > > > cycles);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_T_POST, cycles);
> > > > + cycles = ps2bc(dsi, cfg->hs_exit);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap: 0x%x\n",
> > > > cycles);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_TX_GAP, cycles);
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_EXTRA_CMDS_AFTER_EOTP,
> > > > 0x01);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_HTX_TO_COUNT, 0x00);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_LRX_H_TO_COUNT, 0x00);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_BTA_H_TO_COUNT, 0x00);
> > > > + /* In LP clock cycles */
> > > > + cycles = us2lp(cfg->lp_clk_rate, cfg->wakeup);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_twakeup: 0x%x\n",
> > > > cycles);
> > > > + nwl_dsi_write(dsi, NWL_DSI_CFG_TWAKEUP, cycles);
> > > > +
> > > > + return nwl_dsi_clear_error(dsi);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_config_dpi(struct nwl_dsi *dsi)
> > > > +{
> > > > + u32 mode;
> > > > + int color_format;
> > > > + bool burst_mode;
> > > > + int hfront_porch, hback_porch, vfront_porch, vback_porch;
> > > > + int hsync_len, vsync_len;
> > > > +
> > > > + hfront_porch = dsi->mode.hsync_start - dsi-
> > > > >mode.hdisplay;
> > > > + hsync_len = dsi->mode.hsync_end - dsi->mode.hsync_start;
> > > > + hback_porch = dsi->mode.htotal - dsi->mode.hsync_end;
> > > > +
> > > > + vfront_porch = dsi->mode.vsync_start - dsi-
> > > > >mode.vdisplay;
> > > > + vsync_len = dsi->mode.vsync_end - dsi->mode.vsync_start;
> > > > + vback_porch = dsi->mode.vtotal - dsi->mode.vsync_end;
> > > > +
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "hfront_porch = %d\n",
> > > > hfront_porch);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "hback_porch = %d\n",
> > > > hback_porch);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "hsync_len = %d\n",
> > > > hsync_len);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "hdisplay = %d\n", dsi-
> > > > >
> > > > > mode.hdisplay);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "vfront_porch = %d\n",
> > > > vfront_porch);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "vback_porch = %d\n",
> > > > vback_porch);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "vsync_len = %d\n",
> > > > vsync_len);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "vactive = %d\n", dsi-
> > > > >
> > > > > mode.vdisplay);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "clock = %d kHz\n", dsi-
> > > > >
> > > > > mode.clock);
> > > > +
> > > > + color_format = nwl_dsi_get_dpi_pixel_format(dsi->format);
> > > > + if (color_format < 0) {
> > > > + DRM_DEV_ERROR(dsi->dev, "Invalid color format
> > > > 0x%x\n",
> > > > + dsi->format);
> > > > + return color_format;
> > > > + }
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "pixel fmt = %d\n", dsi-
> > > > >
> > > > > format);
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_INTERFACE_COLOR_CODING,
> > > > NWL_DSI_DPI_24_BIT);
> > > > + nwl_dsi_write(dsi, NWL_DSI_PIXEL_FORMAT, color_format);
> > > > + /*
> > > > + * Adjusting input polarity based on the video mode
> > > > results
> > > > in
> > > > + * a black screen so always pick active low:
> > > > + */
> > > > + nwl_dsi_write(dsi, NWL_DSI_VSYNC_POLARITY,
> > > > + NWL_DSI_VSYNC_POLARITY_ACTIVE_LOW);
> > > > + nwl_dsi_write(dsi, NWL_DSI_HSYNC_POLARITY,
> > > > + NWL_DSI_HSYNC_POLARITY_ACTIVE_LOW);
> > > > +
> > > > + burst_mode = (dsi->dsi_mode_flags &
> > > > MIPI_DSI_MODE_VIDEO_BURST) &&
> > > > + !(dsi->dsi_mode_flags &
> > > > MIPI_DSI_MODE_VIDEO_SYNC_PULSE);
> > > > +
> > > > + if (burst_mode) {
> > > > + nwl_dsi_write(dsi, NWL_DSI_VIDEO_MODE,
> > > > NWL_DSI_VM_BURST_MODE);
> > > > + nwl_dsi_write(dsi, NWL_DSI_PIXEL_FIFO_SEND_LEVEL,
> > > > 256);
> > > > + } else {
> > > > + mode = ((dsi->dsi_mode_flags &
> > > > MIPI_DSI_MODE_VIDEO_SYNC_PULSE) ?
> > > > + NWL_DSI_VM_BURST_MODE_WITH_SYNC_P
> > > > ULSE
> > > > S :
> > > > + NWL_DSI_VM_NON_BURST_MODE_WITH_SY
> > > > NC_E
> > > > VENTS);
> > > > + nwl_dsi_write(dsi, NWL_DSI_VIDEO_MODE, mode);
> > > > + nwl_dsi_write(dsi, NWL_DSI_PIXEL_FIFO_SEND_LEVEL,
> > > > + dsi->mode.hdisplay);
> > > > + }
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_HFP, hfront_porch);
> > > > + nwl_dsi_write(dsi, NWL_DSI_HBP, hback_porch);
> > > > + nwl_dsi_write(dsi, NWL_DSI_HSA, hsync_len);
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_ENABLE_MULT_PKTS, 0x0);
> > > > + nwl_dsi_write(dsi, NWL_DSI_BLLP_MODE, 0x1);
> > > > + nwl_dsi_write(dsi, NWL_DSI_USE_NULL_PKT_BLLP, 0x0);
> > > > + nwl_dsi_write(dsi, NWL_DSI_VC, 0x0);
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_PIXEL_PAYLOAD_SIZE, dsi-
> > > > >
> > > > > mode.hdisplay);
> > > > + nwl_dsi_write(dsi, NWL_DSI_VACTIVE, dsi->mode.vdisplay -
> > > > 1);
> > > > + nwl_dsi_write(dsi, NWL_DSI_VBP, vback_porch);
> > > > + nwl_dsi_write(dsi, NWL_DSI_VFP, vfront_porch);
> > > > +
> > > > + return nwl_dsi_clear_error(dsi);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_init_interrupts(struct nwl_dsi *dsi)
> > > > +{
> > > > + u32 irq_enable;
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK, 0xffffffff);
> > > > + nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK2, 0x7);
> > > > +
> > > > + irq_enable = ~(u32)(NWL_DSI_TX_PKT_DONE_MASK |
> > > > + NWL_DSI_RX_PKT_HDR_RCVD_MASK |
> > > > + NWL_DSI_TX_FIFO_OVFLW_MASK |
> > > > + NWL_DSI_HS_TX_TIMEOUT_MASK);
> > > > +
> > > > + nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK, irq_enable);
> > > > +
> > > > + return nwl_dsi_clear_error(dsi);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_host_attach(struct mipi_dsi_host *dsi_host,
> > > > + struct mipi_dsi_device *device)
> > > > +{
> > > > + struct nwl_dsi *dsi = container_of(dsi_host, struct
> > > > nwl_dsi,
> > > > dsi_host);
> > > > + struct device *dev = dsi->dev;
> > > > + struct drm_bridge *bridge;
> > > > + struct drm_panel *panel;
> > > > + int ret;
> > > > +
> > > > + DRM_DEV_INFO(dev, "lanes=%u, format=0x%x flags=0x%lx\n",
> > > > device->lanes,
> > > > + device->format, device->mode_flags);
> > > > +
> > > > + if (device->lanes < 1 || device->lanes > 4)
> > > > + return -EINVAL;
> > > > +
> > > > + dsi->lanes = device->lanes;
> > > > + dsi->format = device->format;
> > > > + dsi->dsi_mode_flags = device->mode_flags;
> > > > +
> > > > + ret = drm_of_find_panel_or_bridge(dsi->dev->of_node, 1,
> > > > 0,
> > > > &panel,
> > > > + &bridge);
> > > > + if (ret)
> > > > + return ret;
> > > > +
> > > > + if (panel) {
> > > > + bridge = drm_panel_bridge_add(panel);
> > > > + if (IS_ERR(bridge))
> > > > + return PTR_ERR(bridge);
> > > > + }
> > > > +
> > > > + dsi->panel_bridge = bridge;
> > > > + drm_bridge_add(&dsi->bridge);
> > > This works only with a panel, but not with a bridge. For example,
> > > adv7511 bridge, will cal dsi_host_attach in it's drm_bridge_attach
> > > callback. Since you add our bridge only here, the bridge_attach
> > > from
> > > adv7511 will never be called so this callback will never be called.
> > > So, I'd suggest to call drm_bridge_add in probe, and
> > > move drm_of_find_panel_or_bridge in our bridge_attach. Basically,
> > > you
> > > need to separate the bridge_attach operations from the
> > > dsi_host_attach
> > > operations.
> > Makes sense.
> >
> > >
> > >
> > > >
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_host_detach(struct mipi_dsi_host *dsi_host,
> > > > + struct mipi_dsi_device *device)
> > > > +{
> > > > + struct nwl_dsi *dsi = container_of(dsi_host, struct
> > > > nwl_dsi,
> > > > dsi_host);
> > > > +
> > > > + drm_of_panel_bridge_remove(dsi->dev->of_node, 1, 0);
> > > > + drm_bridge_remove(&dsi->bridge);
> > > Also, these removes should be done in our bridge_remove. These are
> > > not
> > > related to the dsi_device.
> > >
> > > >
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static bool nwl_dsi_read_packet(struct nwl_dsi *dsi, u32 status)
> > > > +{
> > > > + struct device *dev = dsi->dev;
> > > > + struct nwl_dsi_transfer *xfer = dsi->xfer;
> > > > + int err;
> > > > + u8 *payload = xfer->msg->rx_buf;
> > > > + u32 val;
> > > > + u16 word_count;
> > > > + u8 channel;
> > > > + u8 data_type;
> > > > +
> > > > + xfer->status = 0;
> > > > +
> > > > + if (xfer->rx_word_count == 0) {
> > > > + if (!(status & NWL_DSI_RX_PKT_HDR_RCVD))
> > > > + return false;
> > > > + /* Get the RX header and parse it */
> > > > + val = nwl_dsi_read(dsi, NWL_DSI_RX_PKT_HEADER);
> > > > + err = nwl_dsi_clear_error(dsi);
> > > > + if (err)
> > > > + xfer->status = err;
> > > > + word_count = NWL_DSI_WC(val);
> > > > + channel = NWL_DSI_RX_VC(val);
> > > > + data_type = NWL_DSI_RX_DT(val);
> > > > +
> > > > + if (channel != xfer->msg->channel) {
> > > > + DRM_DEV_ERROR(dev,
> > > > + "[%02X] Channel mismatch
> > > > (%u !=
> > > > %u)\n",
> > > > + xfer->cmd, channel, xfer-
> > > > >msg-
> > > > >
> > > > > channel);
> > > > + xfer->status = -EINVAL;
> > > > + return true;
> > > > + }
> > > > +
> > > > + switch (data_type) {
> > > > + case
> > > > MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_2BYTE:
> > > > + /* Fall through */
> > > > + case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_2BYTE:
> > > > + if (xfer->msg->rx_len > 1) {
> > > > + /* read second byte */
> > > > + payload[1] = word_count >> 8;
> > > > + ++xfer->rx_len;
> > > > + }
> > > > + /* Fall through */
> > > > + case
> > > > MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_1BYTE:
> > > > + /* Fall through */
> > > > + case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_1BYTE:
> > > > + if (xfer->msg->rx_len > 0) {
> > > > + /* read first byte */
> > > > + payload[0] = word_count & 0xff;
> > > > + ++xfer->rx_len;
> > > > + }
> > > > + xfer->status = xfer->rx_len;
> > > > + return true;
> > > > + case MIPI_DSI_RX_ACKNOWLEDGE_AND_ERROR_REPORT:
> > > > + word_count &= 0xff;
> > > > + DRM_DEV_ERROR(dev, "[%02X] DSI error
> > > > report:
> > > > 0x%02x\n",
> > > > + xfer->cmd, word_count);
> > > > + xfer->status = -EPROTO;
> > > > + return true;
> > > > + }
> > > > +
> > > > + if (word_count > xfer->msg->rx_len) {
> > > > + DRM_DEV_ERROR(
> > > > + dev,
> > > > + "[%02X] Receive buffer too small:
> > > > %zu
> > > > (< %u)\n",
> > > > + xfer->cmd, xfer->msg->rx_len,
> > > > word_count);
> > > > + xfer->status = -EINVAL;
> > > > + return true;
> > > > + }
> > > > +
> > > > + xfer->rx_word_count = word_count;
> > > > + } else {
> > > > + /* Set word_count from previous header read */
> > > > + word_count = xfer->rx_word_count;
> > > > + }
> > > > +
> > > > + /* If RX payload is not yet received, wait for it */
> > > > + if (!(status & NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD))
> > > > + return false;
> > > > +
> > > > + /* Read the RX payload */
> > > > + while (word_count >= 4) {
> > > > + val = nwl_dsi_read(dsi, NWL_DSI_RX_PAYLOAD);
> > > > + payload[0] = (val >> 0) & 0xff;
> > > > + payload[1] = (val >> 8) & 0xff;
> > > > + payload[2] = (val >> 16) & 0xff;
> > > > + payload[3] = (val >> 24) & 0xff;
> > > > + payload += 4;
> > > > + xfer->rx_len += 4;
> > > > + word_count -= 4;
> > > > + }
> > > > +
> > > > + if (word_count > 0) {
> > > > + val = nwl_dsi_read(dsi, NWL_DSI_RX_PAYLOAD);
> > > > + switch (word_count) {
> > > > + case 3:
> > > > + payload[2] = (val >> 16) & 0xff;
> > > > + ++xfer->rx_len;
> > > > + /* Fall through */
> > > > + case 2:
> > > > + payload[1] = (val >> 8) & 0xff;
> > > > + ++xfer->rx_len;
> > > > + /* Fall through */
> > > > + case 1:
> > > > + payload[0] = (val >> 0) & 0xff;
> > > > + ++xfer->rx_len;
> > > > + break;
> > > > + }
> > > > + }
> > > > +
> > > > + xfer->status = xfer->rx_len;
> > > > + err = nwl_dsi_clear_error(dsi);
> > > > + if (err)
> > > > + xfer->status = err;
> > > > +
> > > > + return true;
> > > > +}
> > > > +
> > > > +static void nwl_dsi_finish_transmission(struct nwl_dsi *dsi, u32
> > > > status)
> > > > +{
> > > > + struct nwl_dsi_transfer *xfer = dsi->xfer;
> > > > + bool end_packet = false;
> > > > +
> > > > + if (!xfer)
> > > > + return;
> > > > +
> > > > + if (xfer->direction == DSI_PACKET_SEND &&
> > > > + status & NWL_DSI_TX_PKT_DONE) {
> > > > + xfer->status = xfer->tx_len;
> > > > + end_packet = true;
> > > > + } else if (status & NWL_DSI_DPHY_DIRECTION &&
> > > > + ((status & (NWL_DSI_RX_PKT_HDR_RCVD |
> > > > + NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD))
> > > > )) {
> > > > + end_packet = nwl_dsi_read_packet(dsi, status);
> > > > + }
> > > > +
> > > > + if (end_packet)
> > > > + complete(&xfer->completed);
> > > > +}
> > > > +
> > > > +static void nwl_dsi_begin_transmission(struct nwl_dsi *dsi)
> > > > +{
> > > > + struct nwl_dsi_transfer *xfer = dsi->xfer;
> > > > + struct mipi_dsi_packet *pkt = &xfer->packet;
> > > > + const u8 *payload;
> > > > + size_t length;
> > > > + u16 word_count;
> > > > + u8 hs_mode;
> > > > + u32 val;
> > > > + u32 hs_workaround = 0;
> > > > +
> > > > + /* Send the payload, if any */
> > > > + length = pkt->payload_length;
> > > > + payload = pkt->payload;
> > > > +
> > > > + while (length >= 4) {
> > > > + val = *(u32 *)payload;
> > > > + hs_workaround |= !(val & 0xFFFF00);
> > > > + nwl_dsi_write(dsi, NWL_DSI_TX_PAYLOAD, val);
> > > > + payload += 4;
> > > > + length -= 4;
> > > > + }
> > > > + /* Send the rest of the payload */
> > > > + val = 0;
> > > > + switch (length) {
> > > > + case 3:
> > > > + val |= payload[2] << 16;
> > > > + /* Fall through */
> > > > + case 2:
> > > > + val |= payload[1] << 8;
> > > > + hs_workaround |= !(val & 0xFFFF00);
> > > > + /* Fall through */
> > > > + case 1:
> > > > + val |= payload[0];
> > > > + nwl_dsi_write(dsi, NWL_DSI_TX_PAYLOAD, val);
> > > > + break;
> > > > + }
> > > > + xfer->tx_len = pkt->payload_length;
> > > > +
> > > > + /*
> > > > + * Send the header
> > > > + * header[0] = Virtual Channel + Data Type
> > > > + * header[1] = Word Count LSB (LP) or first param (SP)
> > > > + * header[2] = Word Count MSB (LP) or second param (SP)
> > > > + */
> > > > + word_count = pkt->header[1] | (pkt->header[2] << 8);
> > > > + if (hs_workaround && (dsi->quirks &
> > > > E11418_HS_MODE_QUIRK)) {
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev,
> > > > + "Using hs mode workaround
> > > > for
> > > > cmd 0x%x\n",
> > > > + xfer->cmd);
> > > > + hs_mode = 1;
> > > > + } else {
> > > > + hs_mode = (xfer->msg->flags &
> > > > MIPI_DSI_MSG_USE_LPM) ?
> > > > 0 : 1;
> > > > + }
> > > > + val = NWL_DSI_WC(word_count) | NWL_DSI_TX_VC(xfer->msg-
> > > > >
> > > > > channel) |
> > > > + NWL_DSI_TX_DT(xfer->msg->type) |
> > > > NWL_DSI_HS_SEL(hs_mode) |
> > > > + NWL_DSI_BTA_TX(xfer->need_bta);
> > > > + nwl_dsi_write(dsi, NWL_DSI_PKT_CONTROL, val);
> > > > +
> > > > + /* Send packet command */
> > > > + nwl_dsi_write(dsi, NWL_DSI_SEND_PACKET, 0x1);
> > > > +}
> > > > +
> > > > +static ssize_t nwl_dsi_host_transfer(struct mipi_dsi_host
> > > > *dsi_host,
> > > > + const struct mipi_dsi_msg
> > > > *msg)
> > > > +{
> > > > + struct nwl_dsi *dsi = container_of(dsi_host, struct
> > > > nwl_dsi,
> > > > dsi_host);
> > > > + struct nwl_dsi_transfer xfer;
> > > > + ssize_t ret = 0;
> > > > +
> > > > + /* Create packet to be sent */
> > > > + dsi->xfer = &xfer;
> > > > + ret = mipi_dsi_create_packet(&xfer.packet, msg);
> > > > + if (ret < 0) {
> > > > + dsi->xfer = NULL;
> > > > + return ret;
> > > > + }
> > > > +
> > > > + if ((msg->type & MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM ||
> > > > + msg->type & MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM ||
> > > > + msg->type & MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM ||
> > > > + msg->type & MIPI_DSI_DCS_READ) &&
> > > > + msg->rx_len > 0 && msg->rx_buf != NULL)
> > > > + xfer.direction = DSI_PACKET_RECEIVE;
> > > > + else
> > > > + xfer.direction = DSI_PACKET_SEND;
> > > > +
> > > > + xfer.need_bta = (xfer.direction == DSI_PACKET_RECEIVE);
> > > > + xfer.need_bta |= (msg->flags & MIPI_DSI_MSG_REQ_ACK) ? 1
> > > > : 0;
> > > > + xfer.msg = msg;
> > > > + xfer.status = -ETIMEDOUT;
> > > > + xfer.rx_word_count = 0;
> > > > + xfer.rx_len = 0;
> > > > + xfer.cmd = 0x00;
> > > > + if (msg->tx_len > 0)
> > > > + xfer.cmd = ((u8 *)(msg->tx_buf))[0];
> > > > + init_completion(&xfer.completed);
> > > > +
> > > > + ret = clk_prepare_enable(dsi->rx_esc_clk);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to enable rx_esc
> > > > clk:
> > > > %zd\n",
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "Enabled rx_esc clk @%lu
> > > > Hz\n",
> > > > + clk_get_rate(dsi->rx_esc_clk));
> > > > +
> > > > + /* Initiate the DSI packet transmision */
> > > > + nwl_dsi_begin_transmission(dsi);
> > > > +
> > > > + if (!wait_for_completion_timeout(&xfer.completed,
> > > > + NWL_DSI_MIPI_FIFO_TIMEOU
> > > > T))
> > > > {
> > > > + DRM_DEV_ERROR(dsi_host->dev, "[%02X] DSI transfer
> > > > timed out\n",
> > > > + xfer.cmd);
> > > > + ret = -ETIMEDOUT;
> > > > + } else {
> > > > + ret = xfer.status;
> > > > + }
> > > > +
> > > > + clk_disable_unprepare(dsi->rx_esc_clk);
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static const struct mipi_dsi_host_ops nwl_dsi_host_ops = {
> > > > + .attach = nwl_dsi_host_attach,
> > > > + .detach = nwl_dsi_host_detach,
> > > > + .transfer = nwl_dsi_host_transfer,
> > > > +};
> > > > +
> > > > +static irqreturn_t nwl_dsi_irq_handler(int irq, void *data)
> > > > +{
> > > > + u32 irq_status;
> > > > + struct nwl_dsi *dsi = data;
> > > > +
> > > > + irq_status = nwl_dsi_read(dsi, NWL_DSI_IRQ_STATUS);
> > > > +
> > > > + if (irq_status & NWL_DSI_TX_FIFO_OVFLW)
> > > > + DRM_DEV_ERROR_RATELIMITED(dsi->dev, "tx fifo
> > > > overflow\n");
> > > > +
> > > > + if (irq_status & NWL_DSI_HS_TX_TIMEOUT)
> > > > + DRM_DEV_ERROR_RATELIMITED(dsi->dev, "HS tx
> > > > timeout\n");
> > > > +
> > > > + if (irq_status & NWL_DSI_TX_PKT_DONE ||
> > > > + irq_status & NWL_DSI_RX_PKT_HDR_RCVD ||
> > > > + irq_status & NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD)
> > > > + nwl_dsi_finish_transmission(dsi, irq_status);
> > > > +
> > > > + return IRQ_HANDLED;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_enable(struct nwl_dsi *dsi)
> > > > +{
> > > > + struct device *dev = dsi->dev;
> > > > + union phy_configure_opts *phy_cfg = &dsi->phy_cfg;
> > > > + int ret;
> > > > +
> > > > + if (!dsi->lanes) {
> > > > + DRM_DEV_ERROR(dev, "Need DSI lanes: %d\n", dsi-
> > > > >
> > > > > lanes);
> > > > + return -EINVAL;
> > > > + }
> > > > +
> > > > + ret = phy_init(dsi->phy);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev, "Failed to init DSI phy:
> > > > %d\n",
> > > > ret);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + ret = phy_configure(dsi->phy, phy_cfg);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev, "Failed to configure DSI phy:
> > > > %d\n", ret);
> > > > + goto uninit_phy;
> > > > + }
> > > > +
> > > > + ret = clk_prepare_enable(dsi->tx_esc_clk);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to enable tx_esc
> > > > clk:
> > > > %d\n",
> > > > + ret);
> > > > + goto uninit_phy;
> > > > + }
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "Enabled tx_esc clk @%lu
> > > > Hz\n",
> > > > + clk_get_rate(dsi->tx_esc_clk));
> > > > +
> > > > + ret = nwl_dsi_config_host(dsi);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev, "Failed to set up DSI: %d",
> > > > ret);
> > > > + goto disable_clock;
> > > > + }
> > > > +
> > > > + ret = nwl_dsi_config_dpi(dsi);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev, "Failed to set up DPI: %d",
> > > > ret);
> > > > + goto disable_clock;
> > > > + }
> > > > +
> > > > + ret = phy_power_on(dsi->phy);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev, "Failed to power on DPHY
> > > > (%d)\n",
> > > > ret);
> > > > + goto disable_clock;
> > > > + }
> > > > +
> > > > + ret = nwl_dsi_init_interrupts(dsi);
> > > > + if (ret < 0)
> > > > + goto power_off_phy;
> > > > +
> > > > + return ret;
> > > > +
> > > > +power_off_phy:
> > > > + phy_power_off(dsi->phy);
> > > > +disable_clock:
> > > > + clk_disable_unprepare(dsi->tx_esc_clk);
> > > > +uninit_phy:
> > > > + phy_exit(dsi->phy);
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_disable(struct nwl_dsi *dsi)
> > > > +{
> > > > + struct device *dev = dsi->dev;
> > > > +
> > > > + DRM_DEV_DEBUG_DRIVER(dev, "Disabling clocks and phy\n");
> > > > +
> > > > + phy_power_off(dsi->phy);
> > > > + phy_exit(dsi->phy);
> > > > +
> > > > + /* Disabling the clock before the phy breaks enabling dsi
> > > > again */
> > > > + clk_disable_unprepare(dsi->tx_esc_clk);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_set_platform_clocks(struct nwl_dsi *dsi, bool
> > > > enable)
> > > > +{
> > > > + struct device *dev = dsi->dev;
> > > > + const char *id;
> > > > + struct clk *clk;
> > > > + size_t i;
> > > > + unsigned long rate;
> > > > + int ret, result = 0;
> > > > +
> > > > + DRM_DEV_DEBUG_DRIVER(dev, "%s platform clocks\n",
> > > > + enable ? "enabling" : "disabling");
> > > > + for (i = 0; i < ARRAY_SIZE(dsi->pdata->clk_config); i++)
> > > > {
> > > > + if (!dsi->clk_config[i].present)
> > > > + continue;
> > > > + id = dsi->clk_config[i].id;
> > > > + clk = dsi->clk_config[i].clk;
> > > > +
> > > > + if (enable) {
> > > > + ret = clk_prepare_enable(clk);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev,
> > > > + "Failed to enable
> > > > %s
> > > > clk: %d\n",
> > > > + id, ret);
> > > > + result = result ?: ret;
> > > > + }
> > > > + rate = clk_get_rate(clk);
> > > > + DRM_DEV_DEBUG_DRIVER(dev, "Enabled %s clk
> > > > @%lu Hz\n",
> > > > + id, rate);
> > > > + } else {
> > > > + clk_disable_unprepare(clk);
> > > > + DRM_DEV_DEBUG_DRIVER(dev, "Disabled %s
> > > > clk\n", id);
> > > > + }
> > > > + }
> > > > +
> > > > + return result;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_plat_enable(struct nwl_dsi *dsi)
> > > > +{
> > > > + struct device *dev = dsi->dev;
> > > > + int ret;
> > > > +
> > > > + if (dsi->pdata->select_input) {
> > > > + ret = dsi->pdata->select_input(dsi);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > + }
> > > Since the select_input always reads the dtb (and at runtime this
> > > node
> > > never changes anyway) I think it's best to use the select_input at
> > > probe since it is only needed once and also drop the
> > > deselect_input.
> > >
> > >
> > > >
> > > > +
> > > > + ret = nwl_dsi_set_platform_clocks(dsi, true);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + ret = dsi->pdata->poweron(dsi);
> > > > + if (ret < 0)
> > > > + DRM_DEV_ERROR(dev, "Failed to power on DSI:
> > > > %d\n",
> > > > ret);
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static void nwl_dsi_plat_disable(struct nwl_dsi *dsi)
> > > > +{
> > > > + dsi->pdata->poweroff(dsi);
> > > > + nwl_dsi_set_platform_clocks(dsi, false);
> > > > + if (dsi->pdata->deselect_input)
> > > > + dsi->pdata->deselect_input(dsi);
> > > > +}
> > > > +
> > > > +static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
> > > > +{
> > > > + struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > > +
> > > > + nwl_dsi_disable(dsi);
> > > > + nwl_dsi_plat_disable(dsi);
> > > > + pm_runtime_put(dsi->dev);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_get_dphy_params(struct nwl_dsi *dsi,
> > > > + const struct drm_display_mode
> > > > *mode,
> > > > + union phy_configure_opts
> > > > *phy_opts)
> > > > +{
> > > > + unsigned long rate;
> > > > + int ret;
> > > > +
> > > > + if (dsi->lanes < 1 || dsi->lanes > 4)
> > > > + return -EINVAL;
> > > > +
> > > > + /*
> > > > + * So far the DPHY spec minimal timings work for both
> > > > mixel
> > > > + * dphy and nwl dsi host
> > > > + */
> > > > + ret = phy_mipi_dphy_get_default_config(
> > > > + mode->crtc_clock * 1000,
> > > Why are you using crtc_clock here? I this this should be used only
> > > by
> > > the CRTC component. I'd suggest to use mode->clock here, since it
> > > is
> > > about the output clock of the DSI, not the input clock on the DPI
> > > interface, that is coming from CRTC.
> > crtc_clock is the actual pixel dot clock used which sounds like the
> > one we want to base our calcualations on, no?
>
> From how I see things here, mode->crtc_clock should be the pixel-clock
> coming to the DPI interface from CRTC (input), while mode->clock should
> be the pixel-clock that the DSI periheral expects (output).
> As I told you in another thread, I have a panel (that requires a pixel-
> clock of 132M) that works only when using a smaller pixel-clock at DPI
> interface. In that case, I change the crtc_clock to a lower value
> (evenly divisible by the rate of phy_ref, for ex: 126M) in mode_fixup,
> while keeping the actual clock (of 132M) at DSI ouput. Which is here,
> where the DPHY speed is configured.
I thought you were aiming at that caseh here. Wanted to make sure that
that these are the actaual meanings of mode->crtc_clock and mode->clock
since that's not entirely clear to me from their definition and usage
in other drivers.
> > > > + mipi_dsi_pixel_format_to_bpp(dsi->format), dsi-
> > > > >
> > > > > lanes,
> > > > + &phy_opts->mipi_dphy);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + rate = clk_get_rate(dsi->tx_esc_clk);
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "LP clk is @%lu Hz\n",
> > > > rate);
> > > > + phy_opts->mipi_dphy.lp_clk_rate = rate;
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
> > > > + const struct
> > > > drm_display_mode
> > > > *mode,
> > > > + struct drm_display_mode
> > > > *adjusted_mode)
> > > > +{
> > > > + /* At least LCDIF + NWL needs active high sync */
> > > > + adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> > > > DRM_MODE_FLAG_PVSYNC);
> > > > + adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> > > > DRM_MODE_FLAG_NVSYNC);
> > > > +
> > > > + return true;
> > > > +}
> > > > +
> > > > +static enum drm_mode_status
> > > > +nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> > > > + const struct drm_display_mode *mode)
> > > > +{
> > > > + struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > > + int bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> > > > +
> > > > + if (mode->clock * bpp > 15000000 * dsi->lanes)
> > > > + return MODE_CLOCK_HIGH;
> > > > +
> > > > + if (mode->clock * bpp < 80000 * dsi->lanes)
> > > > + return MODE_CLOCK_LOW;
> > > > +
> > > > + return MODE_OK;
> > > > +}
> > > > +
> > > > +static void
> > > > +nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> > > > + const struct drm_display_mode *mode,
> > > > + const struct drm_display_mode
> > > > *adjusted_mode)
> > > > +{
> > > > + struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > > + struct device *dev = dsi->dev;
> > > > + union phy_configure_opts new_cfg;
> > > > + unsigned long phy_ref_rate;
> > > > + int ret;
> > > > +
> > > > + ret = nwl_dsi_get_dphy_params(dsi, adjusted_mode,
> > > > &new_cfg);
> > > > + if (ret < 0)
> > > > + return;
> > > > +
> > > > + /*
> > > > + * If hs clock is unchanged, we're all good - all
> > > > parameters
> > > > are
> > > > + * derived from it atm.
> > > > + */
> > > > + if (new_cfg.mipi_dphy.hs_clk_rate == dsi-
> > > > >
> > > > > phy_cfg.mipi_dphy.hs_clk_rate)
> > > > + return;
> > > > +
> > > > + phy_ref_rate = clk_get_rate(dsi->phy_ref_clk);
> > > > + DRM_DEV_DEBUG_DRIVER(dev, "PHY at ref rate: %lu\n",
> > > > phy_ref_rate);
> > > > + /* Save the new desired phy config */
> > > > + memcpy(&dsi->phy_cfg, &new_cfg, sizeof(new_cfg));
> > > > +
> > > > + memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
> > > > + drm_mode_debug_printmodeline(adjusted_mode);
> > > > +}
> > > > +
> > > > +static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> > > > +{
> > > > + struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > > +
> > > > + pm_runtime_get_sync(dsi->dev);
> > > > + nwl_dsi_plat_enable(dsi);
> > > > + nwl_dsi_enable(dsi);
> > > > +}
> > > > +
> > > > +static int nwl_dsi_bridge_attach(struct drm_bridge *bridge)
> > > > +{
> > > > + struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > > +
> > > > + return drm_bridge_attach(bridge->encoder, dsi-
> > > > >panel_bridge,
> > > > bridge);
> > > > +}
> > > > +
> > > > +static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
> > > > + .pre_enable = nwl_dsi_bridge_pre_enable,
> > > > + .disable = nwl_dsi_bridge_disable,
> > > > + .mode_fixup = nwl_dsi_bridge_mode_fixup,
> > > > + .mode_set = nwl_dsi_bridge_mode_set,
> > > > + .mode_valid = nwl_dsi_bridge_mode_valid,
> > > > + .attach = nwl_dsi_bridge_attach,
> > > > +};
> > > > +
> > > > +static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
> > > > +{
> > > > + struct platform_device *pdev = to_platform_device(dsi-
> > > > >dev);
> > > > + struct clk *clk;
> > > > + const char *clk_id;
> > > > + void __iomem *base;
> > > > + int i, ret;
> > > > +
> > > > + dsi->phy = devm_phy_get(dsi->dev, "dphy");
> > > > + if (IS_ERR(dsi->phy)) {
> > > > + ret = PTR_ERR(dsi->phy);
> > > > + if (ret != -EPROBE_DEFER)
> > > > + DRM_DEV_ERROR(dsi->dev, "Could not get
> > > > PHY:
> > > > %d\n", ret);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + /* Platform dependent clocks */
> > > > + memcpy(dsi->clk_config, dsi->pdata->clk_config,
> > > > + sizeof(dsi->pdata->clk_config));
> > > > +
> > > > + for (i = 0; i < ARRAY_SIZE(dsi->pdata->clk_config); i++)
> > > > {
> > > > + if (!dsi->clk_config[i].present)
> > > > + continue;
> > > > +
> > > > + clk_id = dsi->clk_config[i].id;
> > > > + clk = devm_clk_get(dsi->dev, clk_id);
> > > > + if (IS_ERR(clk)) {
> > > > + ret = PTR_ERR(clk);
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get %s
> > > > clock: %d\n",
> > > > + clk_id, ret);
> > > > + return ret;
> > > > + }
> > > > + DRM_DEV_DEBUG_DRIVER(dsi->dev, "Setup clk %s
> > > > (rate:
> > > > %lu)\n",
> > > > + clk_id, clk_get_rate(clk));
> > > > + dsi->clk_config[i].clk = clk;
> > > > + }
> > > > +
> > > > + /* DSI clocks */
> > > > + clk = devm_clk_get(dsi->dev, "phy_ref");
> > > > + if (IS_ERR(clk)) {
> > > > + ret = PTR_ERR(clk);
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get phy_ref
> > > > clock:
> > > > %d\n",
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > > + dsi->phy_ref_clk = clk;
> > > > +
> > > > + clk = devm_clk_get(dsi->dev, "rx_esc");
> > > > + if (IS_ERR(clk)) {
> > > > + ret = PTR_ERR(clk);
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get rx_esc
> > > > clock:
> > > > %d\n",
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > > + dsi->rx_esc_clk = clk;
> > > > +
> > > > + clk = devm_clk_get(dsi->dev, "tx_esc");
> > > > + if (IS_ERR(clk)) {
> > > > + ret = PTR_ERR(clk);
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get tx_esc
> > > > clock:
> > > > %d\n",
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > > + dsi->tx_esc_clk = clk;
> > > > +
> > > > + dsi->mux = devm_mux_control_get(dsi->dev, NULL);
> > > > + if (IS_ERR(dsi->mux)) {
> > > > + ret = PTR_ERR(dsi->mux);
> > > > + if (ret != -EPROBE_DEFER)
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get
> > > > mux:
> > > > %d\n", ret);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + base = devm_platform_ioremap_resource(pdev, 0);
> > > > + if (IS_ERR(base))
> > > > + return PTR_ERR(base);
> > > > +
> > > > + dsi->regmap =
> > > > + devm_regmap_init_mmio(dsi->dev, base,
> > > > &nwl_dsi_regmap_config);
> > > > + if (IS_ERR(dsi->regmap)) {
> > > > + ret = PTR_ERR(dsi->regmap);
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to create NWL DSI
> > > > regmap: %d\n",
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + dsi->irq = platform_get_irq(pdev, 0);
> > > > + if (dsi->irq < 0) {
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get device
> > > > IRQ:
> > > > %d\n",
> > > > + dsi->irq);
> > > > + return dsi->irq;
> > > > + }
> > > > +
> > > > + dsi->rstc = devm_reset_control_array_get(dsi->dev, false,
> > > > true);
> > > > + if (IS_ERR(dsi->rstc)) {
> > > > + ret = PTR_ERR(dsi->rstc);
> > > > + if (ret != -EPROBE_DEFER)
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to get
> > > > resets: %d\n",
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > Since you dropped the reset quirk (which is a good idea, but it
> > > needs a
> > > backup), I would like to tell you about our findings. So, as you
> > > know,
> > > DSi can receive input from DCSS or LCDIF (this is done through a
> > > mux).
> > > Now, the reset of the DSI block is not handled directly through the
> > > System Reset Controller (as initially I though). The signals coming
> > > from SRC are going into a reset_sync (Reset Synchronyzer block),
> > > because the DSI block needs the reset signals to be synchronous de-
> > > asserted.
> > > Recently, we discovered the bug that was not allowing us to
> > > correctly
> > > reset the DSI and also why that quirk was initially used.
> > > Normally, the output pixel-clock that was coming from that mux
> > > should
> > > be used as a clock for the reset_sync, but due to a design issue in
> > > the
> > > core, the LCDIF pixel-clock was used to drive this reset_sync.
> > > So, since HW bug here which can be managed in SW, what we did is to
> > > add
> > > the LCDIF pixel-clock to this driver (in dts it can be added as an
> > > external clock needed for reset_sync). I know it is a nasty
> > > external
> > > depencency, but this is the part in SW that fixes the issue in HW.
> > > Now: the LCDIF pixel-clock needs bo be on for the whole duration of
> > > the
> > > DSI operation, This means that LCDIF should be enabled before de-
> > > asserting the reset signals, then disabled after we are done with
> > > DSI
> > > and assert the reset signals back.
> > Pulling in the lcdif clock as optional clock works but how do things
> > work with DCSS? What clock will reset need to be synced there too?
> > 'pix'?
>
> That's the thing. The lcdif clock is viable in this case especiallly
> when DCSS is used as input source. Since, by default, lcdif clock is
> off when using DCSS, the DSI reset won't work. When using LCDIF as
> input source, DSI reset works, since the lcdif clock is on (enabled by
> MXSFB driver).
Great, so we'll fix the dcss case too with that.
> On short: lcdif pixel-clock is needed here when DCSS is used as input-
> source.
>
> >
> > >
> > >
> > > Next, I want to detail you the sequence of the operations that
> > > needs to
> > > be done, since while debugging this issue we received the correct
> > > sequence from Northwest Logic representatives. This sequence is an
> > > absolute requirement for a proper initialization and I will detail
> > > it
> > > below:
> > > 1. De-assert 'pclk' reset (this is needed to have acces to the DSI
> > > registers)
> > > 2. Configure DSI Host
> > > 3. Configure DHPY
> > > 4. Enable DPHY
> > > 5. De-assert 'esc' and 'byte' resets (these are needed for Host TX
> > > operations)
> > > 6. Send DSI commands (if the DSI peripheral needs configuration)
> > > 7. De-assert 'dpi' reset (de-asserting this reset, will enable the
> > > DPI
> > > to start fetching data from it's input and start streaming DSI
> > > data)
> > Very nice! Especially the last part (e.g. keeping the dsi lanes free
> > of
> > signal output until the dsi setup commands went through) answers some
> > questions I asked NXP a while ago in the forums but did not get a
> > reply. That should make things way more robust.
> >
> > >
> > > You will see that I left the 'dpi' reset at the end, so that the
> > > 'DSI
> > > peripheral initialization' step will be clean. DSI lanes needs to
> > > be
> > > clean during this phase and not be "poluted" by any pixel data that
> > > DPI
> > > thinks it needs to stream. On my side, I tried to separate the
> > > above
> > > steps by implementing steps 1-5 in bridge_pre_enable, hoping that
> > > the
> > > step 6 will be automatically run in panel enable phase, and finally
> > > have step 7 implemented in bridge_enable. Unfortunatelly, the order
> > > of
> > > calls for enable is exactly the oposite way as for pre_enable,
> > > which
> > > makes impossible to have the step 7 executed AFTER step 6.
> > > In bridge_pre_enable, the pre_enable for the bridge chain is
> > > executed
> > > first, then our pre_enable is executed.
> > > In bridge_enable, our enable is executed first, then the enable for
> > > brigde chain is executed. This means that step 7 will end up
> > > executed
> > > before step 6, causing the 'DSI lane polution' I was talking above.
> > > As of now, I didn't manage to find a way to fix this, but I will
> > > keep
> > > investigating. If you have a good ideea for this it woule be great.
> > > So, with all the above details, I think you will need to treat each
> > > reset individually, instead of treating them as an array.
> > >
> > > >
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int imx8mq_dsi_select_input(struct nwl_dsi *dsi)
> > > > +{
> > > > + struct device_node *remote;
> > > > + u32 use_dcss = 1;
> > > > + int ret;
> > > > +
> > > > + remote = of_graph_get_remote_node(dsi->dev->of_node, 0,
> > > > + NWL_DSI_ENDPOINT_LCDIF)
> > > > ;
> > > > + if (remote) {
> > > > + use_dcss = 0;
> > > > + } else {
> > > > + remote = of_graph_get_remote_node(dsi->dev-
> > > > >of_node,
> > > > 0,
> > > > + NWL_DSI_ENDPOIN
> > > > T_DC
> > > > SS);
> > > > + if (!remote) {
> > > > + DRM_DEV_ERROR(dsi->dev,
> > > > + "No valid input endpoint
> > > > found\n");
> > > > + return -EINVAL;
> > > > + }
> > > > + }
> > > > +
> > > > + DRM_DEV_INFO(dsi->dev, "Using %s as input source\n",
> > > > + (use_dcss) ? "DCSS" : "LCDIF");
> > > > + ret = mux_control_try_select(dsi->mux, use_dcss);
> > > > + if (ret < 0)
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to select input:
> > > > %d\n", ret);
> > > > +
> > > > + of_node_put(remote);
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static int imx8mq_dsi_deselect_input(struct nwl_dsi *dsi)
> > > > +{
> > > > + int ret;
> > > > +
> > > > + ret = mux_control_deselect(dsi->mux);
> > > > + if (ret < 0)
> > > > + DRM_DEV_ERROR(dsi->dev, "Failed to deselect
> > > > input:
> > > > %d\n", ret);
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +
> > > > +static int imx8mq_dsi_poweron(struct nwl_dsi *dsi)
> > > > +{
> > > > + int ret = 0;
> > > > +
> > > > + /* otherwise the display stays blank */
> > > > + usleep_range(200, 300);
> > > If you implement the part with LCDIF clock detailed above, you can
> > > drop
> > > this sleep. Also, poweron should be replaced by various reset
> > > callbacks
> > > (ex: pclk_reset, mipi_reset, dpi_reset).
> > >
> > > >
> > > > +
> > > > + if (dsi->rstc)
> > > > + ret = reset_control_deassert(dsi->rstc);
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static int imx8mq_dsi_poweroff(struct nwl_dsi *dsi)
> > > > +{
> > > > + int ret = 0;
> > > > +
> > > > + if (dsi->rstc)
> > > > + ret = reset_control_assert(dsi->rstc);
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static const struct drm_bridge_timings nwl_dsi_timings = {
> > > > + .input_bus_flags = DRM_BUS_FLAG_DE_LOW,
> > > > +};
> > > > +
> > > > +static const struct nwl_dsi_platform_data imx8mq_dev = {
> > > > + .poweron = &imx8mq_dsi_poweron,
> > > > + .poweroff = &imx8mq_dsi_poweroff,
> > > > + .select_input = &imx8mq_dsi_select_input,
> > > > + .deselect_input = &imx8mq_dsi_deselect_input,
> > > > + .clk_config = {
> > > > + { .id = NWL_DSI_CLK_CORE, .present = true },
> > > > + },
> > > > +};
> > > > +
> > > > +static const struct of_device_id nwl_dsi_dt_ids[] = {
> > > > + { .compatible = "fsl,imx8mq-nwl-dsi", .data =
> > > > &imx8mq_dev, },
> > > > + { /* sentinel */ }
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, nwl_dsi_dt_ids);
> > > > +
> > > > +static const struct soc_device_attribute nwl_dsi_quirks_match[]
> > > > = {
> > > > + { .soc_id = "i.MX8MQ", .revision = "2.0",
> > > > + .data = (void *)E11418_HS_MODE_QUIRK },
> > > > + { /* sentinel. */ },
> > > > +};
> > > > +
> > > > +static int nwl_dsi_probe(struct platform_device *pdev)
> > > > +{
> > > > + struct device *dev = &pdev->dev;
> > > > + const struct of_device_id *of_id =
> > > > of_match_device(nwl_dsi_dt_ids, dev);
> > > > + const struct nwl_dsi_platform_data *pdata = of_id->data;
> > > > + const struct soc_device_attribute *attr;
> > > > + struct nwl_dsi *dsi;
> > > > + int ret;
> > > > +
> > > > + dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
> > > > + if (!dsi)
> > > > + return -ENOMEM;
> > > > +
> > > > + dsi->dev = dev;
> > > > + dsi->pdata = pdata;
> > > > +
> > > > + ret = nwl_dsi_parse_dt(dsi);
> > > > + if (ret)
> > > > + return ret;
> > > > +
> > > > + ret = devm_request_irq(dev, dsi->irq,
> > > > nwl_dsi_irq_handler, 0,
> > > > + dev_name(dev), dsi);
> > > > + if (ret < 0) {
> > > > + DRM_DEV_ERROR(dev, "Failed to request IRQ %d:
> > > > %d\n",
> > > > dsi->irq,
> > > > + ret);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + dsi->dsi_host.ops = &nwl_dsi_host_ops;
> > > > + dsi->dsi_host.dev = dev;
> > > > + ret = mipi_dsi_host_register(&dsi->dsi_host);
> > > > + if (ret) {
> > > > + DRM_DEV_ERROR(dev, "Failed to register MIPI host:
> > > > %d\n", ret);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + attr = soc_device_match(nwl_dsi_quirks_match);
> > > > + if (attr)
> > > > + dsi->quirks = (uintptr_t)attr->data;
> > > > +
> > > > + dsi->bridge.driver_private = dsi;
> > > > + dsi->bridge.funcs = &nwl_dsi_bridge_funcs;
> > > > + dsi->bridge.of_node = dev->of_node;
> > > > + dsi->bridge.timings = &nwl_dsi_timings;
> > > > +
> > > > + dev_set_drvdata(dev, dsi);
> > > > + pm_runtime_enable(dev);
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int nwl_dsi_remove(struct platform_device *pdev)
> > > > +{
> > > > + struct nwl_dsi *dsi = platform_get_drvdata(pdev);
> > > > +
> > > > + mipi_dsi_host_unregister(&dsi->dsi_host);
> > > > + pm_runtime_disable(&pdev->dev);
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static struct platform_driver nwl_dsi_driver = {
> > > > + .probe = nwl_dsi_probe,
> > > > + .remove = nwl_dsi_remove,
> > > > + .driver = {
> > > > + .of_match_table = nwl_dsi_dt_ids,
> > > > + .name = DRV_NAME,
> > > > + },
> > > > +};
> > > > +
> > > > +module_platform_driver(nwl_dsi_driver);
> > > > +
> > > > +MODULE_AUTHOR("NXP Semiconductor");
> > > > +MODULE_AUTHOR("Purism SPC");
> > > > +MODULE_DESCRIPTION("Northwest Logic MIPI-DSI driver");
> > > > +MODULE_LICENSE("GPL"); /* GPLv2 or later */
> > > > diff --git a/drivers/gpu/drm/bridge/nwl-dsi.h
> > > > b/drivers/gpu/drm/bridge/nwl-dsi.h
> > > > new file mode 100644
> > > > index 000000000000..a247a8a11c7c
> > > > --- /dev/null
> > > > +++ b/drivers/gpu/drm/bridge/nwl-dsi.h
> > > > @@ -0,0 +1,144 @@
> > > > +/* SPDX-License-Identifier: GPL-2.0+ */
> > > > +/*
> > > > + * NWL MIPI DSI host driver
> > > > + *
> > > > + * Copyright (C) 2017 NXP
> > > > + * Copyright (C) 2019 Purism SPC
> > > > + */
> > > > +#ifndef __NWL_DSI_H__
> > > > +#define __NWL_DSI_H__
> > > > +
> > > > +/* DSI HOST registers */
> > > > +#define NWL_DSI_CFG_NUM_LANES 0x0
> > > > +#define NWL_DSI_CFG_NONCONTINUOUS_CLK 0x4
> > > > +#define NWL_DSI_CFG_T_PRE 0x8
> > > > +#define NWL_DSI_CFG_T_POST 0xc
> > > > +#define NWL_DSI_CFG_TX_GAP 0x10
> > > > +#define NWL_DSI_CFG_AUTOINSERT_EOTP 0x14
> > > > +#define NWL_DSI_CFG_EXTRA_CMDS_AFTER_EOTP 0x18
> > > > +#define NWL_DSI_CFG_HTX_TO_COUNT 0x1c
> > > > +#define NWL_DSI_CFG_LRX_H_TO_COUNT 0x20
> > > > +#define NWL_DSI_CFG_BTA_H_TO_COUNT 0x24
> > > > +#define NWL_DSI_CFG_TWAKEUP 0x28
> > > > +#define NWL_DSI_CFG_STATUS_OUT 0x2c
> > > > +#define NWL_DSI_RX_ERROR_STATUS 0x30
> > > > +
> > > > +/* DSI DPI registers */
> > > > +#define NWL_DSI_PIXEL_PAYLOAD_SIZE 0x200
> > > > +#define NWL_DSI_PIXEL_FIFO_SEND_LEVEL 0x204
> > > > +#define NWL_DSI_INTERFACE_COLOR_CODING 0x208
> > > > +#define NWL_DSI_PIXEL_FORMAT 0x20c
> > > > +#define NWL_DSI_VSYNC_POLARITY 0x210
> > > > +#define NWL_DSI_VSYNC_POLARITY_ACTIVE_LOW 0
> > > > +#define NWL_DSI_VSYNC_POLARITY_ACTIVE_HIGH BIT(1)
> > > > +
> > > > +#define NWL_DSI_HSYNC_POLARITY 0x214
> > > > +#define NWL_DSI_HSYNC_POLARITY_ACTIVE_LOW 0
> > > > +#define NWL_DSI_HSYNC_POLARITY_ACTIVE_HIGH BIT(1)
> > > > +
> > > > +#define NWL_DSI_VIDEO_MODE 0x218
> > > > +#define NWL_DSI_HFP 0x21c
> > > > +#define NWL_DSI_HBP 0x220
> > > > +#define NWL_DSI_HSA 0x224
> > > > +#define NWL_DSI_ENABLE_MULT_PKTS 0x228
> > > > +#define NWL_DSI_VBP 0x22c
> > > > +#define NWL_DSI_VFP 0x230
> > > > +#define NWL_DSI_BLLP_MODE 0x234
> > > > +#define NWL_DSI_USE_NULL_PKT_BLLP 0x238
> > > > +#define NWL_DSI_VACTIVE 0x23c
> > > > +#define NWL_DSI_VC 0x240
> > > > +
> > > > +/* DSI APB PKT control */
> > > > +#define NWL_DSI_TX_PAYLOAD 0x280
> > > > +#define NWL_DSI_PKT_CONTROL 0x284
> > > > +#define NWL_DSI_SEND_PACKET 0x288
> > > > +#define NWL_DSI_PKT_STATUS 0x28c
> > > > +#define NWL_DSI_PKT_FIFO_WR_LEVEL 0x290
> > > > +#define NWL_DSI_PKT_FIFO_RD_LEVEL 0x294
> > > > +#define NWL_DSI_RX_PAYLOAD 0x298
> > > > +#define NWL_DSI_RX_PKT_HEADER 0x29c
> > > > +
> > > > +/* DSI IRQ handling */
> > > > +#define NWL_DSI_IRQ_STATUS 0x2a0
> > > > +#define NWL_DSI_SM_NOT_IDLE BIT(0)
> > > > +#define NWL_DSI_TX_PKT_DONE BIT(1)
> > > > +#define NWL_DSI_DPHY_DIRECTION BIT(2)
> > > > +#define NWL_DSI_TX_FIFO_OVFLW BIT(3)
> > > > +#define NWL_DSI_TX_FIFO_UDFLW BIT(4)
> > > > +#define NWL_DSI_RX_FIFO_OVFLW BIT(5)
> > > > +#define NWL_DSI_RX_FIFO_UDFLW BIT(6)
> > > > +#define NWL_DSI_RX_PKT_HDR_RCVD BIT(7)
> > > > +#define NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD BIT(8)
> > > > +#define NWL_DSI_BTA_TIMEOUT BIT(29)
> > > > +#define NWL_DSI_LP_RX_TIMEOUT BIT(30)
> > > > +#define NWL_DSI_HS_TX_TIMEOUT BIT(31)
> > > > +
> > > > +#define NWL_DSI_IRQ_STATUS2 0x2a4
> > > > +#define NWL_DSI_SINGLE_BIT_ECC_ERR BIT(0)
> > > > +#define NWL_DSI_MULTI_BIT_ECC_ERR BIT(1)
> > > > +#define NWL_DSI_CRC_ERR BIT(2)
> > > > +
> > > > +#define NWL_DSI_IRQ_MASK 0x2a8
> > > > +#define NWL_DSI_SM_NOT_IDLE_MASK BIT(0)
> > > > +#define NWL_DSI_TX_PKT_DONE_MASK BIT(1)
> > > > +#define NWL_DSI_DPHY_DIRECTION_MASK BIT(2)
> > > > +#define NWL_DSI_TX_FIFO_OVFLW_MASK BIT(3)
> > > > +#define NWL_DSI_TX_FIFO_UDFLW_MASK BIT(4)
> > > > +#define NWL_DSI_RX_FIFO_OVFLW_MASK BIT(5)
> > > > +#define NWL_DSI_RX_FIFO_UDFLW_MASK BIT(6)
> > > > +#define NWL_DSI_RX_PKT_HDR_RCVD_MASK BIT(7)
> > > > +#define NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD_MASK BIT(8)
> > > > +#define NWL_DSI_BTA_TIMEOUT_MASK BIT(29)
> > > > +#define NWL_DSI_LP_RX_TIMEOUT_MASK BIT(30)
> > > > +#define NWL_DSI_HS_TX_TIMEOUT_MASK BIT(31)
> > > > +
> > > > +#define NWL_DSI_IRQ_MASK2 0x2ac
> > > > +#define NWL_DSI_SINGLE_BIT_ECC_ERR_MASK BIT(0)
> > > > +#define NWL_DSI_MULTI_BIT_ECC_ERR_MASK BIT(1)
> > > > +#define NWL_DSI_CRC_ERR_MASK BIT(2)
> > > > +
> > > > +/*
> > > > + * PKT_CONTROL format:
> > > > + * [15: 0] - word count
> > > > + * [17:16] - virtual channel
> > > > + * [23:18] - data type
> > > > + * [24] - LP or HS select (0 - LP, 1 - HS)
> > > > + * [25] - perform BTA after packet is sent
> > > > + * [26] - perform BTA only, no packet tx
> > > > + */
> > > > +#define NWL_DSI_WC(x) FIELD_PREP(GENMASK(15, 0), (x))
> > > > +#define NWL_DSI_TX_VC(x) FIELD_PREP(GENMASK(17, 16), (x))
> > > > +#define NWL_DSI_TX_DT(x) FIELD_PREP(GENMASK(23, 18), (x))
> > > > +#define NWL_DSI_HS_SEL(x) FIELD_PREP(GENMASK(24, 24), (x))
> > > > +#define NWL_DSI_BTA_TX(x) FIELD_PREP(GENMASK(25, 25), (x))
> > > > +#define NWL_DSI_BTA_NO_TX(x) FIELD_PREP(GENMASK(26, 26), (x))
> > > > +
> > > > +/*
> > > > + * RX_PKT_HEADER format:
> > > > + * [15: 0] - word count
> > > > + * [21:16] - data type
> > > > + * [23:22] - virtual channel
> > > > + */
> > > > +#define NWL_DSI_RX_DT(x) FIELD_GET(GENMASK(21, 16), (x))
> > > > +#define NWL_DSI_RX_VC(x) FIELD_GET(GENMASK(23, 22), (x))
> > > > +
> > > > +/* DSI Video mode */
> > > > +#define NWL_DSI_VM_BURST_MODE_WITH_SYNC_PULSES 0
> > > > +#define NWL_DSI_VM_NON_BURST_MODE_WITH_SYNC_EVENTS BIT(0)
> > > > +#define NWL_DSI_VM_BURST_MODE BIT(1)
> > > > +
> > > > +/* * DPI color coding */
> > > > +#define NWL_DSI_DPI_16_BIT_565_PACKED 0
> > > > +#define NWL_DSI_DPI_16_BIT_565_ALIGNED 1
> > > > +#define NWL_DSI_DPI_16_BIT_565_SHIFTED 2
> > > > +#define NWL_DSI_DPI_18_BIT_PACKED 3
> > > > +#define NWL_DSI_DPI_18_BIT_ALIGNED 4
> > > > +#define NWL_DSI_DPI_24_BIT 5
> > > > +
> > > > +/* * DPI Pixel format */
> > > > +#define NWL_DSI_PIXEL_FORMAT_16 0
> > > > +#define NWL_DSI_PIXEL_FORMAT_18 BIT(0)
> > > > +#define NWL_DSI_PIXEL_FORMAT_18L BIT(1)
> > > > +#define NWL_DSI_PIXEL_FORMAT_24 (BIT(0) | BIT(1))
> > > > +
> > > > +#endif /* __NWL_DSI_H__ */
> > > > --
> > > > 2.23.0
> > > >
> > > >
> > > I know it's a lot of information here and, since I already have
> > > that
> > > implemented on my side, do you want me to send the next revision,
> > > or do
> > > you want to implement it on your own?
> > I'm fine with making (and testing) the changes but if you have some
> > code
> > (even against an older driver version) i can borrow from in a tree
> > somewhere you can link to (or send via mail) that'd certainly speed
> > up
> > things.
>
> Sure. I can send you what I have, but my local version is based on v3
> of this patch-set. Still, you can make an idea of how things should be
> done.
> I will send you in private the patches.
Thanks! I'll add a proper reset sequence to get rid of the arbitrary
sleep and make dcss work as well. That said I wouldn't mind the driver
being merged and putting that on top since it's basically improvements
on top. If not i'll fold this into v9.
Cheers,
-- Guido
>
> Best regards,
> Robert
>
> >
> > Cheers,
> > -- Guido
> >
> > >
> > >
> > > Best regards,
> > > Robert
Powered by blists - more mailing lists