| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1576116600.21256.3.camel@mhfsdcap03>
Date: Thu, 12 Dec 2019 10:10:00 +0800
From: Chunfeng Yun <chunfeng.yun@...iatek.com>
To: Marek Szyprowski <m.szyprowski@...sung.com>
CC: <linux-usb@...r.kernel.org>, <linux-samsung-soc@...r.kernel.org>,
<linux-mediatek@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Krzysztof Kozlowski <krzk@...nel.org>,
Matthias Brugger <matthias.bgg@...il.com>,
Maxime Ripard <mripard@...nel.org>,
Chen-Yu Tsai <wens@...e.org>, Andy Gross <agross@...nel.org>,
Bjorn Andersson <bjorn.andersson@...aro.org>,
"Stefan Agner" <stefan@...er.ch>,
Linus Walleij <linus.walleij@...aro.org>,
Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
Subject: Re: [PATCH v2 4/4] usb: usb3503: Convert to use GPIO descriptors
On Wed, 2019-12-11 at 15:52 +0100, Marek Szyprowski wrote:
> From: Linus Walleij <linus.walleij@...aro.org>
>
> This converts the USB3503 to pick GPIO descriptors from the
> device tree instead of iteratively picking out GPIO number
> references and then referencing these from the global GPIO
> numberspace.
>
> The USB3503 is only used from device tree among the in-tree
> platforms. If board files would still desire to use it they can
> provide machine descriptor tables.
>
> Make sure to preserve semantics such as the reset delay
> introduced by Stefan.
>
> Cc: Chunfeng Yun <chunfeng.yun@...iatek.com>
> Cc: Marek Szyprowski <m.szyprowski@...sung.com>
> Cc: Stefan Agner <stefan@...er.ch>
> Cc: Krzysztof Kozlowski <krzk@...nel.org>
> Signed-off-by: Linus Walleij <linus.walleij@...aro.org>
> [mszyprow: invert the logic behind reset GPIO line]
> Signed-off-by: Marek Szyprowski <m.szyprowski@...sung.com>
> ---
> drivers/usb/misc/usb3503.c | 94 ++++++++++-----------------
> include/linux/platform_data/usb3503.h | 3 -
> 2 files changed, 35 insertions(+), 62 deletions(-)
>
> diff --git a/drivers/usb/misc/usb3503.c b/drivers/usb/misc/usb3503.c
> index 72f39a9751b5..116bd789e568 100644
> --- a/drivers/usb/misc/usb3503.c
> +++ b/drivers/usb/misc/usb3503.c
> @@ -7,11 +7,10 @@
>
> #include <linux/clk.h>
> #include <linux/i2c.h>
> -#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> #include <linux/delay.h>
> #include <linux/slab.h>
> #include <linux/module.h>
> -#include <linux/of_gpio.h>
> #include <linux/platform_device.h>
> #include <linux/platform_data/usb3503.h>
> #include <linux/regmap.h>
> @@ -47,19 +46,19 @@ struct usb3503 {
> struct device *dev;
> struct clk *clk;
> u8 port_off_mask;
> - int gpio_intn;
> - int gpio_reset;
> - int gpio_connect;
> + struct gpio_desc *intn;
> + struct gpio_desc *reset;
> + struct gpio_desc *connect;
> bool secondary_ref_clk;
> };
>
> static int usb3503_reset(struct usb3503 *hub, int state)
> {
> - if (!state && gpio_is_valid(hub->gpio_connect))
> - gpio_set_value_cansleep(hub->gpio_connect, 0);
> + if (!state && hub->connect)
> + gpiod_set_value_cansleep(hub->connect, 0);
>
> - if (gpio_is_valid(hub->gpio_reset))
> - gpio_set_value_cansleep(hub->gpio_reset, state);
> + if (hub->reset)
> + gpiod_set_value_cansleep(hub->reset, !state);
What about preparing another patch for @state before this path?
>
> /* Wait T_HUBINIT == 4ms for hub logic to stabilize */
> if (state)
> @@ -115,8 +114,8 @@ static int usb3503_connect(struct usb3503 *hub)
> }
> }
>
> - if (gpio_is_valid(hub->gpio_connect))
> - gpio_set_value_cansleep(hub->gpio_connect, 1);
> + if (hub->connect)
> + gpiod_set_value_cansleep(hub->connect, 1);
>
> hub->mode = USB3503_MODE_HUB;
> dev_info(dev, "switched to HUB mode\n");
> @@ -163,13 +162,11 @@ static int usb3503_probe(struct usb3503 *hub)
> int err;
> u32 mode = USB3503_MODE_HUB;
> const u32 *property;
> + enum gpiod_flags flags;
> int len;
>
> if (pdata) {
> hub->port_off_mask = pdata->port_off_mask;
> - hub->gpio_intn = pdata->gpio_intn;
> - hub->gpio_connect = pdata->gpio_connect;
> - hub->gpio_reset = pdata->gpio_reset;
> hub->mode = pdata->initial_mode;
> } else if (np) {
> u32 rate = 0;
> @@ -230,59 +227,38 @@ static int usb3503_probe(struct usb3503 *hub)
> }
> }
>
> - hub->gpio_intn = of_get_named_gpio(np, "intn-gpios", 0);
> - if (hub->gpio_intn == -EPROBE_DEFER)
> - return -EPROBE_DEFER;
> - hub->gpio_connect = of_get_named_gpio(np, "connect-gpios", 0);
> - if (hub->gpio_connect == -EPROBE_DEFER)
> - return -EPROBE_DEFER;
> - hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
> - if (hub->gpio_reset == -EPROBE_DEFER)
> - return -EPROBE_DEFER;
> of_property_read_u32(np, "initial-mode", &mode);
> hub->mode = mode;
> }
>
> - if (hub->port_off_mask && !hub->regmap)
> - dev_err(dev, "Ports disabled with no control interface\n");
> -
> - if (gpio_is_valid(hub->gpio_intn)) {
> - int val = hub->secondary_ref_clk ? GPIOF_OUT_INIT_LOW :
> - GPIOF_OUT_INIT_HIGH;
> - err = devm_gpio_request_one(dev, hub->gpio_intn, val,
> - "usb3503 intn");
> - if (err) {
> - dev_err(dev,
> - "unable to request GPIO %d as interrupt pin (%d)\n",
> - hub->gpio_intn, err);
> - return err;
> - }
> - }
> -
> - if (gpio_is_valid(hub->gpio_connect)) {
> - err = devm_gpio_request_one(dev, hub->gpio_connect,
> - GPIOF_OUT_INIT_LOW, "usb3503 connect");
> - if (err) {
> - dev_err(dev,
> - "unable to request GPIO %d as connect pin (%d)\n",
> - hub->gpio_connect, err);
> - return err;
> - }
> - }
> -
> - if (gpio_is_valid(hub->gpio_reset)) {
> - err = devm_gpio_request_one(dev, hub->gpio_reset,
> - GPIOF_OUT_INIT_LOW, "usb3503 reset");
> + if (hub->secondary_ref_clk)
> + flags = GPIOD_OUT_LOW;
> + else
> + flags = GPIOD_OUT_HIGH;
> + hub->intn = devm_gpiod_get_optional(dev, "intn", flags);
> + if (IS_ERR(hub->intn))
> + return PTR_ERR(hub->intn);
> + if (hub->intn)
> + gpiod_set_consumer_name(hub->intn, "usb3503 intn");
> +
> + hub->connect = devm_gpiod_get_optional(dev, "connect", GPIOD_OUT_LOW);
> + if (IS_ERR(hub->connect))
> + return PTR_ERR(hub->connect);
> + if (hub->connect)
> + gpiod_set_consumer_name(hub->connect, "usb3503 connect");
> +
> + hub->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(hub->reset))
> + return PTR_ERR(hub->reset);
> + if (hub->reset) {
> /* Datasheet defines a hardware reset to be at least 100us */
> usleep_range(100, 10000);
> - if (err) {
> - dev_err(dev,
> - "unable to request GPIO %d as reset pin (%d)\n",
> - hub->gpio_reset, err);
> - return err;
> - }
> + gpiod_set_consumer_name(hub->reset, "usb3503 reset");
> }
>
> + if (hub->port_off_mask && !hub->regmap)
> + dev_err(dev, "Ports disabled with no control interface\n");
> +
> usb3503_switch_mode(hub, hub->mode);
>
> dev_info(dev, "%s: probed in %s mode\n", __func__,
> diff --git a/include/linux/platform_data/usb3503.h b/include/linux/platform_data/usb3503.h
> index e049d51c1353..d01ef97ddf36 100644
> --- a/include/linux/platform_data/usb3503.h
> +++ b/include/linux/platform_data/usb3503.h
> @@ -17,9 +17,6 @@ enum usb3503_mode {
> struct usb3503_platform_data {
> enum usb3503_mode initial_mode;
> u8 port_off_mask;
> - int gpio_intn;
> - int gpio_connect;
> - int gpio_reset;
> };
>
> #endif
Powered by blists - more mailing lists